INSTRUCTION MANUAL CCA-BC200 Rear View Back up Camera System CAUTION • Installation and wiring require technical expertise and experience. To ensure proper installation and safety, consult the dealer where the product was purchased. SANYO’S HELP-LINE Call the toll-free number below if you have any difficulties operating this product.
-1-
CONTENTS SAFETY PRECAUTIONS···································································································· 2 SPECIFICATION ················································································································· 4 BEFORE USING THE REAR VIEW BACK UP CAMERA SYSTEM···································· 5 ACCESSORIES AND HARDWARE ···················································································· 6 REAR VIEW BACK UP CAMERA SYSTEM OUTLINE ·············
• • • • • • • • • • • • When installing this Rear View Back up Camera System to a vehicle equipped with air bags (The name differs depending on the manufacturer, such as SRS dual air bag, SRS side air bag, SRS curtain air bag), do not install this Rear View Back up Camera System or route its wiring where it affects operation of the air bag system. If the air bags do not operate properly in an emergency, an accident or injury can occur.
• • • • • • • Route wiring properly according to the instructions. An incorrect connection might cause a fire or accident. Be careful and prevent the wiring harness from being pinched between the vehicle body, screws, or moving parts such as the seat rails. It could cause an accident, electrocution, or fire due to an open or short circuit. The Rear View Back up Camera System is for in-car use only and is not to be used outside of the vehicle.
BEFORE USING THE REAR VIEW BACK UP CAMERA SYSTEM Regarding methods of use • • • • • The Rear View Back up Camera System is a devise designed only to assist the driver. The driver must take full precautions to confirm the safety and conditions around the vehicle. Water droplets on the camera lens could adversely affect the image. The positioning appearing on the screen changes according to the vehicle conditions (number of occupants and weight of cargo).
ACCESSORIES AND HARDWARE Make sure all the following parts are included in the Rear View Back up Camera System kit. 1 Rear view camera………1 pc. (with approx. 26.2 ft. long cable) ECU box…….........….1 pc. (Electronic Control Unit box) Bracket (for camera)…1 pc. (with double sided tape) Power supply cable……1 pc. (approx. 4.92 ft. long, with fuse) Hook-and-loop fastener…1 set (for ECU box) Screw (for camera)…2 pcs. (Hexagon type, M3 x 6) Cable clamp…10 pcs. Cable tie……2 pcs. Waterproof pad…1 pc.
REAR VIEW BACK UP CAMERA SYSTEM OUTLINE Camera Virtual camera Display mode View-from-top Including the standard rear view image captured by the camera, a digitally corrected rear view, view-from-top, and standard rear view can be selected. Guide lines are indicated in order to assist the driver and assure safety when backing up. Standard rear view Standard rear view Digitally corrected rear view Left/right guide lines (Green) (Guide lines to indicate width of vehicle) 6 ft.
CAUTIONS FOR CONNECTION CAUTION • Before connecting, disconnect the negative battery terminal. Connect the negative battery terminal after all other connections are completed. • Connection terminals and cables are differentiated by color. Make connections to the same colors. Make sure connectors are securely inserted until a click sound is heard. Incomplete connection may cause a distorted picture or operation errors. • Before disconnecting the connector, turn the ignition switch to the off position.
CONNECTION Power supply connection terminal (Brown) Power supply cable (Brown) Connect firmly to a metal part of vehicle (for grounding) (Black) Video output connection terminal (Yellow) (Black) Connect the cable according to the color and shape of the terminal Rear view camera connection terminal (Black) ECU box (Green) Control switch connection terminal (Green) (Yellow) Video output cable (RCA Type) (Yellow) Connect to the reverse signal cable of vehicle using self-lock conductor included with
BEFORE INSTALLATION Rear View Back up Camera System Installation Cautions • • • • • • • Bundle cables with tape or string so that they do not obstruct driving. Cables that become entangled in the steering wheel, shift selector lever or brake pedal could cause an accident. Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to the surface of the vehicle. If the tape is not completely adhered to the surface, the camera bracket might become loose and fall off.
Determination of Camera Installation Position (example) • • • • • Temporarily adhering the camera with the tape, locate a suitable installation position by adjusting the camera angle so that the rear of the vehicle (bumper and other areas) is visible in the monitor. Install the camera in a position that does not allow the illumination of a high-mount brake light to reflect into the camera lens. Make sure the camera does not contact or rub against the vehicle body when the rear door opens or closes.
INSTALLATION Installing system on rear spoiler 1. Clean the location where the camera is to be installed. Wipe off oil, wax, moisture, dirt and dust using a cleaner and a clean cloth. 2. Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to a flat surface on the rear spoiler. Press the bracket with a finger to assure good contact of the bracket to the surface of the vehicle.
4. Adjust the camera angle so that the extreme rear end of the vehicle (bumper, rear window, and liftgate.) is displayed at the bottom of the monitor. Need help? Call 1-800-421-5013 • Extreme rear end of vehicle (bumper etc.) After adjusting the angle, tighten the screws with them seated at the lower end of the oblong holes in the bracket on each side. Loosen Tighten CAUTION • Verify the tightness of the screws and tighten them more if necessary.
Control switch 7. Install the control switch in a position where it is easy to operate. Peel off the paper backing on the back of the control switch and attach it to a suitable position. CAUTION • Do not install the control switch in a position that obstructs vehicle operation. How to use self-lock conductor 1. Insert the reverse signal cable of the vehicle into the self-lock conductor. Vehicle reverse signal cable 2. Fold the self-lock conductor and lock the reverse signal cable. Cable stopper 3.
CABLE ROUTING The following is an example when installing the camera on the rear spoiler. Control switch Camera ECU box CAUTION • • • Route the cable so that it does not block or obstruct vehicle operation. Route the rear view camera cable as far away from the vehicle antenna as possible to prevent noise interference with AM radio band reception. Also, route the cable as far as possible from a TV antenna, if equipped. Clean the areas where the cable clamps and waterproof pad are to be attached.
3. Route the camera cable to the ECU box positioned inside the vehicle and clamp it using the cable clamps. Insert the cable into the slit provided in the waterproof pad and attach the waterproof pad to the weather strip on the vehicle at the point where the cable enters the vehicle. Luggage finish plate 0.1 in 0.1 in Position with no ribs on the rear side Waterproof pad Weather strip 4. Route the control switch cable to the ECU box and secure it with cable clamps.
GUIDE LINE ADJUSTMENT AFTER REAR VIEW CAMERA INSTALLATION The guide lines on the screen need to be aligned with the image taken from the rear view camera (and other reference items) so that the system is correctly matched to the vehicle. There are seven reference items to align including, (1) View-from-top angle alignment (2) Center-line alignment (3) View-from-top height alignment (4) Left/right guide lines alignment (5) Right guide line alignment (6) 3 ft. guide line alignment (7) 1.5 ft.
Alignment Mode Seven rectangles at top left indicate seven items to align Turn the ignition switch to the ACC ON position while depressing the control switch. • Press and hold the control switch until the screen appears. View-from-top alignment screen appears. (Seven rectangles at top left indicate seven items to align.) If adjustment mode cannot be selected 1. Turn the ignition switch to the ACC ON position while pressing the switch. Press and hold the switch for two seconds or more. 2.
1. View-from-top angle alignment (flashing white rectangle) 1-1. Each time the control switch is pressed, the angle increases. Continuously pressing the control switch returns the alignment to the original angle. Set the parking space lines parallel to the lines on the screen. 1-2. Press and hold the control switch for more than two seconds. The view-from-top angle alignment is now set and the screen changes to the center-line alignment setting. The center guide line is shown in red on the screen. 2.
3. View-from-top height alignment (flashing violet rectangle) 3-1. Press the control switch to change to a higher or lower view-from-top. Select a view-from-top height so that the markers indicating the width of the vehicle can be seen better on the screen. 3-2. Press and hold the control switch for more than two seconds. The view-from-top height alignment is now set and the screen changes to the left/right guide lines alignment setting. Left/right guide lines are indicated in red on the screen. 4.
5. Right guide line alignment (flashing green rectangle) 5-1. Each time the control switch is pressed, the right guide line moves towards the center. Continuously pressing the control switch moves the guide line to its maximum right position. Set the right guide line to match the right-side marker of the vehicle. 5-2. Press and hold the control switch for more than two seconds. The right guide line alignment is now set and the screen changes to the 3 ft. guide line alignment setting. The 3 ft.
7. 1.5 ft. guide line alignment (flashing blue rectangle) 7-1. Each time the control switch is pressed, the 1.5 ft. guide line moves farther from the vehicle. Continuously pressing the control switch moves the line farther away until it exceeds a certain range and the line returns to the position closest to the vehicle. Set the1.5 ft. guide line to match the 1.5 ft. marker. 7-2. Press and hold the control switch for more than two seconds. The 1.5 ft. guide line alignment is now set and also 6 ft.
REAR VIEW BACK UP CAMERA DISPLAY AND SWITCHING DISPLAY MODES Preparation prior to use Make sure the ignition switch is in the ON or ACC position. CAUTION • If the image turns off automatically after the guide line alignment, turn the ignition switch off, then to the ACC ON or ON position prior to the following procedure. 1. Turn the monitor on and select the input mode switch to view the image from the rear view camera on the screen. (Refer to the instruction manual for the monitor for details.) 2.
