Computer Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point◄► buttons to adjust the setting value. Image adjust Menu Contrast Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Computer Input Store To store the adjusted data, select Store and press the Point ► button or the SELECT button. Use the Point ▲▼ buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select Yes. Stored data can be called up by selecting an Image (1–4) in the Image Mode Selection on page 33. A confirmation box appears and then select Yes.
Computer Input Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom and the Custom is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust. Scale H/V........... Adjust the Horizontal/Vertical screen scale. H&V.................... When set to On, the aspect ratio is fixed. The Scale V appears dimmed and becomes unavailable.
Computer Input Keystone This function is used to adjust keystone distortion of the projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. Keystone To correct keystone distortion, press the SELECT button. Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p.23). Store To store or reset the keystone correction, press the SELECT button. Store .............Keep the keystone correction even when the AC power cord is unplugged. Reset............
Video Input Input Source Selection (Video, S-video) Direct Operation Choose Video or S-video by pressing the INPUT button on the top control, or the VIDEO button or the S-VIDEO button on the remote control. Before using INPUT button, correct input source should be selected through menu operation as described below.
Video Input Input Source Selection (Component, Scart) Direct Operation Choose Computer 1(Component) or Computer 1(Scart) by pressing the INPUT button on the top control or press the COMPUTER 1 or the COMPONENT button on the remote control. Before using INPUT button, correct input source should be selected through Menu operation as described below.
Video Input Video System Selection 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Video, S-video or Computer 1(Component) and then press the SELECT button. 3 Use the Point ▲▼ buttons to select System and then press the Point ► or SELECT button. Use the Point ▲▼ buttons to select the desired system and then press the SELECT button.
Video Input Image Mode Selection Direct Operation Remote Control Select the desired image mode among Dynamic, Standard, Real, Cinema, Blackboard (Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control. IMAGE button Dynamic Standard Real Menu Operation 1 2 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image select and then press the Point ► or the SELECT button.
Video Input Image Adjustment 1 2 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select the Image adjust and then press the Point ► or the SELECT button. Image adjust Menu Use the Point ▲▼ buttons to select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value. Contrast Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Video Input Sharpness Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15). Gamma Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Noise reduction Noise interference on the screen can be reduced. Select one of the following options to get smoother images. Off.......... Disabled. L 1.......... Lower reduction L 2..........
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons select the desired item and then press the SELECT button. Screen Menu Normal Provide the image to fit the screen size. Full Provide the full screen image.
Video Input Keystone This function is used to adjust keystone distortion of the projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. Keystone To correct keystone distortion, press the SELECT button. Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p.23). Store To store or reset the keystone correction, press the SELECT button. Store ............Keep the keystone correction even when the AC power cord is unplugged. Reset............
Setting Setting This projector has a Setting menu that allows you to set up the other various functions described below. 1 2 3 Press the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons to select the Setting and press the Point ► or the SELECT button to access the submenu items. Use the Point ▲▼ buttons to select the desired item and then press the Point ► or the SELECT buttons to access the selected item.
Setting Auto setup Auto setup This function enables Input search, Auto Keystone correction and Auto PC adjustment by pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control. Settings for those functions can be altered as follows: Input search This function detects the input signal automatically. When a signal is found, the search will stop. Use the Point ▲▼ buttons to select one of the following options. Off............ Input search will not work. On 1.........
Setting Background Select the background screen when no input signal is detected. Press the Point ▲▼ buttons to switch between each option. Blue . . . Project a blue background User . . Project an image captured in the Logo setting. Black . . Project a black background Display This function decides whether to display On-Screen Displays. On............................ Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough.
Setting Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Capture Select Capture and press the SELECT button. A confirmation box appears and select Yes to capture the projected image. After capturing the projected image, go to the Logo select function and set it to User. Then the captured image will be displayed the next time you turn on the projector.
Setting Enter a Logo PIN code Use the Point ▲▼ buttons to enter a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to “”. If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Repeat this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to Set.
Setting Power management Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period. Select one of the following options: Ready................... When the lamp has been fully cooled down, the POWER indicator changes to green blinking.
Setting Standby mode This function is available when operating the projector via network. Eco............. Select Eco when you do not use the projector via network. The projector’s network function will stop when turning off the projector. Network..... Supply the power to the network function even after turning off the projector. You can turn on/ off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off.
Setting Closed caption Closed Caption Closed caption is a function that displays the audio portion of a TV program as text on the screen. If the input signal contains closed captions, you can turn on the feature and switch the channels. Press the Point ▲▼ buttons to select Off, CC 1, CC 2, CC 3 or CC 4. If the closed caption is not clear, you can change the text from Color to White. Note: The Closed caption is available only under the situation below.
Setting Lamp control Lamp life control Lamp control This function allows you to change brightness of the screen. Auto........... Brightness according to the input signal. Normal....... The lamp power output is maximum. Eco 1.......... The lamp power output is 70% of the Normal mode. Eco 2.......... The lamp power output is 53% of the Normal mode. Lamp life control Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use. Mode 1...............
Setting Fan control Choose the running speed of cooling fans from the following options according to the ground elevation under which you use the projector. Off................ Normal speed. Set this function to Off when using the projector in non-high altitude environment. On 1............. Faster than Off mode. Select this mode when using the projector in high altitudes (about 1,200 meters or more above the sea level) where the fans have less cooling effect. On 2............. Faster than On 1 mode.
Setting Total power savings This function displays the saved amount of power and the exhausted CO2 of the projector. Total power savings Use the Point ▲▼ buttons to select Total power savings and then press the Point ► or the SELECT button to access the submenu items. Total power savings......Show the total accumulated power savings of the projector and display the total amount of CO2 exhausted from the projector. Reset...............................
Maintenance and Cleaning Replacing the Filters Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. If a “Filter warning” icon appears on the screen, replace the filters immediately. Replace the filters by following the steps below.
Maintenance and Cleaning Attaching the Lens Cap When moving this projector or while not using it over an extended period of time, replace the lens cap. Attach the lens cap according to the following procedures. 1 Thread the string through the hole on the lens cap and then tie a knot in the string to secure it in place. 2 To pass the other end of the string into the hole on the top of the projector and pull at it. Cleaning the Projection Lens Unplug the AC power cord before cleaning.
Maintenance and Cleaning Lamp Replacement When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.
Maintenance and Cleaning ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : LC-XB250A : POA-LMP148 (Service Parts No. 610 352 7949) LAMP HANDLING PRECAUTIONS This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.
Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER red/green WARNING red Projector Condition LAMP REPLACE yellow The projector is off. (The AC power cord is unplugged.) The projector is in stand-by mode. Press the ON/STAND-BY button to turn on the projector. The projector is operating normally. The projector is preparing for stand-by or the projection lamp is being cooled down.
Appendix Technical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 13.78" x 3.44" x 10.02" (350.0 mm X 87.5 mm X 254.4 mm ) (Not including protrusions) Net Weight 7.50 lbs (3.4 kg) Feet Adjustment 0˚ to 12˚ Panel Resolution LCD Panel System 0.
Appendix Dimensions Unit: mm(inch) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.472) 216.5 (8.52) 208.0 (8.19) 86.0 (3.38) 57.9 (2.28) 73.6 (2.90) 133.1 (5.24) 115.3 (4.54) 93.2 (3.67) 45.1 (1.78) 185.2 (7.29) 142.0 (5.59) 276.9 (10.90) 76.9 (3.03) 42.1 (1.66) 47.0 (1.85) 60.0 (2.36) 74.1 (2.92) 81.1 (3.19) 42.0 (1.65) 40.4 (1.59) 78.0 (3.07) 78 57.4 (2.26) 240.0 (9.45) 39.1 (1.54) 52.3 (2.06) 209.0 (8.23) 212.4 (8.36) 121.5 (4.78) 254.4 (10.02) 46.2 (1.28) 67.9 (2.67) 64.
