User's Manual

ManualsBrandsSANYO Electronics ManualsElectronicsMultimedia Projector

Setting

Key lock

Security (Key lock and PIN code lock)

PIN code lock

Thisfunctionlocksthetopcontrolandremotecontrol

buttonstopreventoperationbyunauthorizedpersons.

.....

Unlocked.

..... Locktheoperationofthetopcontrol.To

unlock,usetheremotecontrol.

..... Locktheoperationoftheremotecontrol.

Tounlock,usethetopcontrol.

Ifthetopcontrolaccidentallybecomeslockedandyoudo

nothavetheremotecontrolnearbyorthereissomething

wrongwithyourremotecontrol,contactthedealerwhere

youpurchasedtheprojectorortheservicecenter.

ThisfunctionallowsyoutousetheKeylockandPINcode

lockfunctiontosetthesecurityfortheprojectoroperation.

Thisfunctionpreventstheprojectorfrombeingoperated

byunauthorizedpersonsandprovidesthefollowing

settingoptionsforsecurity.

 Off...........Unlocked.

 On1.........EnterthePINcodeeverytimeturningon

theprojector.

 On2.........EnterthePINcodetooperatetheprojector

oncethepowercordisdisconnected;as

longastheACpowercordisconnected,

theprojectorcanbeoperatedwithouta

PINcode.

WheneveryouchangethePINcodelocksettingorthe

PINcode(thefour-digitnumber),youarerequiredto

enterthePINcode.The"1234"issetastheinitialPIN

codeatthefactory.

IfyouwanttochangethePINcodelocksetting,Press

theSELECTbuttonandthePINcodedialogbox

appears.

Off

PIN code lock

Off

Summary of content (27 pages)

PAGE 1
Setting Security (Key lock and PIN code lock) Key lock This function allows you to use the Key lock and PIN code lock function to set the security for the projector operation. Key lock This function locks the top control and remote control buttons to prevent operation by unauthorized persons. ...... Unlocked. ...... Lock the operation of the top control. To unlock, use the remote control. ...... Lock the operation of the remote control. To unlock, use the top control.
PAGE 2
Setting Enter a PIN code Use the Point ▲▼ buttons to enter a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Enter a PIN code Repeat this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to Set.
PAGE 3
Setting Fan This function provides the following options in the cooling fans’ operation when the projector is turned off (p.23). L1....... Normal operation L2....... Slower and lower-sound than the normal operation (L1), but it takes more time to cool the projector down. Fan control Choose the running speed of cooling fans from the following options according to the ground elevation under which you use the projector. Off.......Normal speed.
PAGE 4
Setting Filter counter This function is used to set a frequency for the filter cleaning. When the projector reached a specified time between cleanings, a Filter warning icon appears on the screen, notifying the cleaning is necessary. After cleaning the filter, be sure to select Reset and set the timer. The Filter warning icon will not turn off until the filter counter is reset. Filter counter 32H For details about resetting the timer, refer to "Resetting the Filter Counter" on page 65. Fig.
PAGE 5
Information Input Source Information Display The Information Menu is used for checking the status of the image signal being projected and the operation of the projector. Direct Operation Press the INFO. button on the remote control to display the Information Menu. Remote Control INFO. button Menu Operation Press the Point ▲▼ buttons to select Information. The Information Menu is displayed. See below for displayed information. Input The selected input source is displayed. Information Menu H-sync freq.
PAGE 6
Maintenance and Cleaning WARNING indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red. Top Control When the temperature inside the projector reaches a certain level, the projector will be automatically shut down to protect the inside of the projector.
PAGE 7
Maintenance and Cleaning Cleaning the Filters Filter prevents dust from accumulating on the optical elements inside the projector. Should the filters become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. If a Filter warning icon appears on the screen, clean the filters immediately. Clean the filters by following the steps below.
PAGE 8
Maintenance and Cleaning Lens Cap Attaching the Lens Cap When moving the projector or while it is not in use, replace the lens cap. 1 Thread the string through the hole on the lens cap and then tie a knot in the string to secure it in place. 2 To pass the other end of the string into the hole on the top of the projector and pull at it. Hole Cleaning the Projection Lens Unplug the AC power cord before cleaning.
PAGE 9
Maintenance and Cleaning Lamp Replacement When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.
PAGE 10
Maintenance and Cleaning Resetting the Lamp Counter Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP REPLACE indicator stops lighting and the Lamp replacement icon disappears. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Setting and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Lamp counter and then press the SELECT button.
PAGE 11
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. –Make sure you have properly connected the projector to peripheral equipment as described on pages 17-19. –Make sure all equipment is connected to AC outlet and the power is turned on. –When the projector does not project an image from the connected computer, restart the computer. Problem: – Solutions – Plug the power cord of the projector into the AC outlet.
PAGE 12
Appendix – Check the connection between your computer or video equipment and the projector. See pages 17-19. – See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer’s instruction manual for the setting. – It takes about 30 seconds to display an image after turning on the projector. See page 21. – Check the Input signal, color system, video system or computer system mode.
PAGE 13
Appendix – Check PC adjustment or Screen and adjust them. The image is distorted or runs off. See pages 34-35, 38-39 . PIN code dialog box appears at start-up. – PIN code lock is being set. Enter a PIN code ("1234" or numbers you have set). See pages 22, 59-60. Page Up/Down function does not – Make sure your computer is connected to the projector with USB work. cable. See page 17.
PAGE 14
Appendix WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem. We will advise you how to obtain service. The CE Mark is a Directive conformity mark of the European Community (EC). Pixelworks ICs used.
PAGE 15
Appendix Menu Tree Computer Input/HDMI Input/Video Input Input Input RGB Computer 1 Component RGB (Scart) RGB Computer 2 HDMI Video S-video Network Sound Sound Volume Mute 0-63 On/Off Computer Input Image Select System (1) SVGA 1 Mode 1 Mode 2 ---- * Systems displayed in the System Menu vary depending on an input signal. Auto PC adj.
PAGE 16
Appendix HDMI Input / Video Input System (2) Setting Setting Auto 1080i 1035i 720p 575p 480p 575i 480i System (3) Auto PAL SECAM NTSC NTSC 4.43 PAL-M PAL-N Language Menu position Auto setup 17 languages provided. Input search Off/On1/On2 Auto PC adj.
PAGE 17
Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER WARNING red/green red Projector Condition LAMP REPLACE yellow The projector is off. (The AC power cord is unplugged.)  The projector is in stand-by mode. Press the ON/STAND-BY button to turn on the projector.  The projector is operating normally.  The projector is preparing for stand-by or the projection lamp is being cooled down.
PAGE 18
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock for analog signal and 110 MHz of Dot Clock for digital signal. When selecting these modes, PC adjustment can be limited. When the input signal is Analog , refer to the chart below.
PAGE 19
Appendix When the input signal is digital from HDMI terminal, refer to the chart below.
PAGE 20
Appendix List of Picture in Picture o : Picture in Picture combinations are enabled - : Picture in Picture combinations are disabled Note: • When the input signal(s) is/are incompatible, X mark will be displayed on the Main/Sub picture. • Depending on the frequency or signal type of PC/AV input, the display resolution may be lowered or images may not be displayed on the Main/Sub picture.
PAGE 21
Appendix Technical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 13.16" x 3.09" x 10.14" (334.2 x 78.4 x 257.5mm) (Not including protrusions) Net Weight 7.94 lbs (3.6 kg) Feet Adjustment 0˚ to 8.9˚ Panel Resolution LCD Panel System 0.
PAGE 22
Appendix Accessories Owner’s Manual (CD-ROM) Quick Reference Guide Safety Manual AC Power Cord Remote Control and Batteries VGA Cable Lens Cap with String PIN Code Label Network Application (CD-ROM) Soft Carrying Case USB thumb drive for Auto Capture Case (for USB thumb drive) Hook and Loop Fastener ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.
PAGE 23
Appendix PJ Link Notice This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see page 51 on the owner’s manual of “Network Set-up and Operation.
PAGE 24
Appendix Configurations of Terminals COMPUTER IN 1 /COMPONENT IN /MONITOR OUT (ANALOG) Terminal: Analog RGB (Mini D-sub 15 pin) 4 5 10 15 3 9 14 2 8 13 1 7 12 6 11 1 2 3 4 5 6 7 8 Red (R/Cr) Input/Output Green (G/Y) Input/Output Blue (B/Cb) Input/Output 1 2 3 4 5 6 7 8 9 10 TMDS Data 2+ Input Ground (TMDS Data 2) TMDS Data 2- Input TMDS Data 1+ Input Ground (TMDS Data 1) TMDS Data 1- Input TMDS Data 0+ Input Ground (TMDS Data 0) TMDS Data 0- Input TMDS Clock+ Input ----Ground (Horiz.sync.
PAGE 25
Appendix PIN Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* *Should the four-digit number be changed, the factory set number will be invalid. While the projector is locked with the PIN code.
PAGE 26
Appendix Dimensions Unit: inch (mm) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.472) 13.16(334.2) 3.09(78.4) 3.66(93.0) 2.14(53.8) 3.17(80.5) 5.51(140.0) 5.08(129.0) 84 5.20(132.0) 2.78(70.5) 10.14 (257.5) 5.08(129.0) 4.43(112.
PAGE 27
KY7AE SANYO Electric Co., Ltd.