MLL11 Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE Before getting started, let’s make sure this mount is perfect for you! 1 Does your TV weigh more than 130 lb (58.9 kg) including accessories? 130 lb No — Perfect! (58.9 kg) Yes — This mount is NOT compatible. Visit MountFinder.Sanus.com or call 1-800-359-5520 (UK: 0800-056-2853) to find a compatible mount.
Dimensions 635 mm 25 in. 50 mm to 705 mm 178 mm 7.01 in. 484 mm 19.05 in. 76.2 mm 3 in. 177.8 mm 7 in. 120.7 mm 4.75 in. 25.6 mm 1.01 in. 475 mm 18.7 in. 702.1 mm 27.64 in.
Parts and Hardware WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 2 Concrete Anchors Wall Plate 15 x4 Washers 14 x1 16 x4 Lag Bolts 5/16 ¾ in. 5/16x x22.75 in.
STEP 1 Attach Brackets to TV 1-1 Select TV Screw Diameter 1-2 Select TV Screw Length Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M5, M6, or M8) to use. If your TV has a flat back AND you want your TV closer to the wall, use the shorter screws (a).
1-3 Attach TV Brackets Ensure that your brackets 01 and 02 are level on the back of the TV. Standard configurations are shown. For special applications, or if you are unsure about your hardware selection, contact Customer Service. a Flat Back 03 04 05 06 07 02 For ease of access, straps should be level with the bottom of the TV.
STEP 2A Attach Wall Plate to Wall - Wood Stud CAUTION: Avoid potential personal injuries and property damage! • • • Drywall covering the wall must not exceed 5/8 in. (16 mm) Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) Minimum horizontal space between fasteners: 16 in. (406 mm) 1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder. 2.
3. Pilot holes MUST be drilled to a depth of 3 in. (75 mm), using a 7/32 in. (5.5 mm) diameter drill bit. 3. Tighten the lag bolts 17 only until the washers 16 are pulled firmly against the wall plate 14 . CAUTION: Avoid potential injuries or property damage! Improper use could reduce the holding power of the lag bolt 17 . To avoid potential injuries or property damage. DO NOT over-tighten the lag bolts 17 . 4 3 3 in. (75 mm) 17 7/32 in. (5.
STEP 2B Attach Wall Plate to Wall - Solid Concrete or Concrete Block CAUTION: Avoid potential personal injuries and property damage! • • • • Mount the wall plate 14 directly onto the concrete surface Minimum solid concrete thickness: 8 in. (203 mm) Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm) Minimum horizontal space between fasteners: 16 in. (406 mm) 1. Level the wall plate 14 and mark the hole locations. 2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
3. Insert four anchors 15 and install the wall plate 14 using four lag bolts 17 and four washers 16 . Tighten the lag bolts 17 only until the washers 16 are pulled firmly against the wall plate 14 . CAUTION: Be sure the anchors 15 are seated flush with the concrete surface. CAUTION: Improper use could reduce the holding power of the lag bolt 17 . DO NOT over-tighten the lag bolts 17 .
STEP 3 Hang the TV with Mounting Brackets on the Wall Plate Install the TV / Bracket assembly by fitting the top hook of the mounting brackets 01 and 02 over the top edge of the wall plate 14 . Swing the mounting brackets down until the spring loaded locking tabs slip over and fully engages the bottom edge of the wall plate 14 . You will hear an audible "CLICK". HEAVY! You may need assistance with this step.
To remove the TV, pull the straps down to disengage the locking tabs, swing the TV / bracket assembly forward from the bottom, and then lift the TV up and off, away from the wall plate 14 . HEAVY! You may need assistance with this step.
ESPAÑOL INSTRUCCIONES DE SEGURIDAD IMPORTANTES. CONSÉRVELAS. LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO. Antes de comenzar, verifiquemos que este soporte sea el ideal para sus necesidades. 1 ¿Su televisor pesa más de 58.9 kg (130 lb), incluidos los accesorios? No — ¡Perfecto! 58.9 kg Sí — Este soporte NO es compatible. Visite MountFinder.Sanus.com o llame al 1-800-359-5520 (Reino Unido: 0800-056-2853) para encontrar un (130 lb) soporte compatible.
ESPAÑOL Dimensiones Ver página 3 Piezas y elementos de sujeción suministrados Ver página 4 ADVERTENCIA: Este producto contiene piezas pequeñas que, si fuesen tragadas, podrían producir asfixia. Antes de iniciar el ensamblaje, compruebe que todas las piezas estén incluidas y en buenas condiciones. Si faltan piezas o alguna está dañada, no devuelva el artículo al distribuidor; póngase en contacto con el servicio de atención al cliente. Nunca utilice piezas deterioradas.
ESPAÑOL PASO 2A Fijar la placa mural a la pared - Opción para montantes de madera Ver página 8 PRECAUCIÓN: Evite posibles lesiones personales y daños materiales. ƕ ƕ El yeso que recubre la pared no debe exceder los 16 mm (5/8 pulgada). Tamaño mínimo del montante de madera: común 51 mm x 102 mm (2 x 4 pulgadas) (nominal 38 mm x 89 mm [1½ x 3½ pulgadas]). 1. Localice el o los montantes. Verifique el centro del montante con un punzón o un clavo delgado, o bien utilice un detector de bordes de montantes.
3. Introduzca cuatro anclajes 15 e instale el módulo de la placa mural 14 usando cuatro tornillos tirafondo 17 y cuatro arandelas 16 . Ajuste los tornillos tirafondo 17 solamente hasta que queden firmes contra la placa mural 14 . PRECAUCIÓN: El uso indebido podría reducir la capacidad de retención de los tornillos tirafondo 17 . NO ajuste en exceso los tornillos tirafondo 17 .
FRANÇAIS CONSIGNES DE SÉCURITÉ IMPORTANTES – CONSERVEZ CES INSTRUCTIONS – VEUILLEZ LIRE ATTENTIVEMENT LE MANUEL AVANT D’UTILISER CE PRODUIT Avant de commencer, assurons-nous que ce support vous convient parfaitement! 1 Votre téléviseur pèse-t-il plus de 58.9 kg (130 lb) avec les accessoires? 58.9 kg (130 lb) 2 3 Non — Parfait! Oui — Ce support n'est PAS compatible. Visitez MountFinder.Sanus.com ou composez le 1 800 359-5520 pour trouver un support compatible.
FRANÇAIS Dimensiones Dimensions Voir à la page 3 Pièces et quincaillerie fournies Voir à la page 4 AVERTISSEMENT: Ce produit contient de petites pièces qui peuvent représenter un risque d’étouffement. Avant de commencer l’assemblage, assurez-vous que toutes les pièces sont présentes et qu’elles ne sont pas endommagées. Si une pièce est manquante ou endommagée, ne retournez pas les pièces endommagées à votre revendeur. Contactez plutôt le service clientèle.
FRANÇAIS ÉTAPE 2A Option montant de bois Voir à la page 8 ATTENTION : Évitez les dommages matériels et les blessures! ƕ ƕ L’épaisseur du matériau de revêtement de mur ne doit pas excéder 16 mm (5/8 po). Dimension minimale du montant de bois : commune 51 x 102 mm (2 x 4 po) nominale 38 x 89 mm (1,5 x 3,5 po) 1. Vérifiez le centre du montant à l’aide d’un poinçon ou d’un clou fin, ou utilisez un localisateur bord à bord. 2. Mettez la plaque murale 14 à niveau et marquez les emplacements des trous. 3.
FRANÇAIS ÉTAPE 3 Suspendre le téléviseur avec les supports de montage sur la plaque murale Voir à la page 12 Dimensiones Lors de l’installation du moniteur à la plaque murale, assurez-vous que les pattes de verrouillage s’enclenchent bien en position verrouillée. Vous devriez entendre un clic lorsque les pièces sont correctement assemblées.
Thank you for choosing Sanus Classic! Please take a moment to let us know how we did: Call us: 1-800-359-5520 UK: 0800 056 2853 Email us: info@sanus.com Find us on Facebook: SANUS Leave a review: sanus.com Follow us on Twitter @sanussystems Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete.
