USER MANUAL 1-Channel IP Video Server Model: SVS-3001 Version 1.
Dear customer, Thank you for purchasing a high quality SANTEC device. We recommend that you read this manual thoroughly before operating your new system for the first time. Please follow all instructions and observe the warnings contained in this manual. Please contact your local dealer or SANTEC directly if you have any questions or if you wish to claim for a service or warranty. You will find further information on our website: www.santec-video.com All rights reserved.
User Manual SVS-3001 Table of contents Safety precautions 5 Safety instructions 6 About this user manual 7 Quick installation guide 8 PART I: CONNECTIONS; CABLING, TECHNICAL SPECIFICATIONS 1. General 1.1 Included items 1.2 System requirements 9 9 9 2. Connectors and ports 10 3. Connection of hardware components 11 4. Technical specifications 12 Appendix: Setup Internet security 13 PART II: CONFIGURATION AND CONTROL VIA THE WEB 1. General 14 2. Menu overview 2.1 Administration page 2.
User Manual SVS-3001 2.6. Schedule 2.6.1 General 2.6.2 Storage 2.7 Network 2.7.1 General 2.7.2 Advanced 2.7.3 SMTP (e-mail) 2.7.4 DDNS 2.8 System 2.8.1 Information 2.8.2 User 2.8.3 Date & time 2.8.4 Server maintenance 2.8.
User Manual SVS-3001 Safety precautions Caution Description of symbols Danger: This symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to a person. Warning: This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
User Manual SVS-3001 Safety instructions Before operating the appliance, please read this manual carefully and retain it for further reference. Before cleaning the appliance, it has to be switched off and unplugged from the power outlet. Wipe the appliance with a soft damp cloth. Do not use harsh cleansers or aerosols for cleaning. The type label may not be replaced.
User Manual SVS-3001 In case of any operating interruption or a complete operating failure please switch off the appliance and disconnect it from the wall outlet. Never attempt to service or repair the appliance yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
User Manual SVS-3001 QUICK INSTALLATION GUIDE To operate the video server, please follow these steps: 1. Connect the hardware components as follows: 1. Prepare a PC/laptop with an Ethernet link to the network. 2. Connect the SVS-3001 video server to a network hub/switch with a standard pass through (CAT5) cable. You may also connect SVS-3001 directly to the PC/laptop using a cross over cable. 3. Connect the video output of the camera using standard 75 Ohm coaxial cable terminated with BNC connector. 4.
User Manual SVS-3001 Part I: Connection, installation, technical specifications 1. General The SANTEC 1-channel IP video server SVS-3001 can encode and transmit video signals from analogue cameras into an IP signal with MJPEG or H.264 compression. 1.1 Items included in the delivery 1x 1x 1x 1x 1x Video server SVS-3001 CD (IP finder and user manual) Quick installation guide Power adapter Breakout cable 1.
User Manual SVS-3001 2.
User Manual SVS-3001 Reset button: The reset button is used to restore the factory default settings. To do so, please follow these steps: 1. Unplug the power jack to turn off the video server. 2. Insert a pin into the reset hole and press and hold the reset button for approx. 10 seconds. 3. Plug-in the power jack to turn on the video server while keep pressing the reset button. The power LED will start flashing after a short while. 4. Release the pin when the LED starts quick flashing.
User Manual SVS-3001 4. Technical specifications Device Type SVS-3001 1-channel video server Video input/output 1x BNC / 1x BNC Compression (video) Number of video streams Resolution Max.
User Manual SVS-3001 Appendix: Internet security setup If ActiveX control installation is blocked, please either set the Internet security level to default or change ActiveX controls and plug-in settings. Internet security level: Default: 1. 2. 3. 4. Open the „Internet Options“ menu. Select “Security”. Click on „Reset all zones to default level“. Confirm by clicking “Apply” or “OK”. If the default settings don’t work, please use the customized settings for ActiveX Controls.
User Manual SVS-3001 Part II: Control via the web 1. General The SVS-3001 video server is equipped with a user-friendly browser-based configuration interface. In this part of the user manual, information on system related settings and control options will be described in detail. Start your web browser and enter the URL or the IP address in the address field: Default IP address: Default username Default password: : 192.168.1.
User Manual SVS-3001 2.2 Live view Admin button (go to administration page) Language setting PTZ control panel Action buttons (Full screen, talk, speaker, snapshot, recording) Channel selection Supported languages: On the live view page, you can select your language by clicking on the respective flag icon: English or German. Admin button: To exit the and to make changes to the camera set-up, click on the button.
User Manual SVS-3001 Action buttons: Full screen Click this button to display the live image as full screen. To exit the full screen view and to return to the regular view, please double-click into the full screen image. Talk The talk function allows the local site to talk to the remote site. Click on the button to switch it to on/off. Note: This function is only open to a “user” who has been granted this privilege by the administrator. Speaker Click on this button to mute/activate the audio function.
User Manual SVS-3001 PTZ control panel: The PTZ control panel is only displayed when PTZ has been enabled (see chapter “2.4.2 PTZ”). Pan/tilt arrows: Click to move the image. “+” and “-“: Click to zoom in/out. PTZ presets: List of presets. Alternatively, instead of using the PTZ control panel, you may simply click into the live view picture to move it (SANTEC “EasyViewPTZ” technology). Note: The OSD button (in the middle of the control panel) and the tour function are only available using a Pelco protocol.
User Manual SVS-3001 2.3 Video Under the tab
User Manual SVS-3001 2.3.2 Advanced The video setting can be found under the path: Video > Advanced RTSP path: The RTSP path is the stream ID used for RTSP client streaming connection, such as VLC player. The default values are v00, v01 and v02 for the three streams respectively. The string can be any combination of number or capital/small letters. It cannot be empty, however. Resolution: The resolution describes an image size counted by width and height referring to pixel resolution.
User Manual SVS-3001 Image format: H.264 and MJPEG are available for image format selection. The term “image format” is referring to compression/encoding technique. The selected image format influences the performance of bandwidth and storage requirement. With regards to video quality, H.264 contributes to less bandwidth and storage requirement, which is more efficient than MJPEG. GOP: GOP (group of pictures) describes how the different types of frames are arranged.
User Manual SVS-3001 2.4 Camera Under the tab
User Manual SVS-3001 2.4.2 PTZ The camera setting can be found under the path: Camera > PTZ PTZ status: Select “enable” or “disable. The PTZ control panel in live view is only displayed if the PTZ status is set to “enable”. PTZ protocol: The following protocols are supported: Pelco D, Pelco P, Li-Lin, Li-Lin New, Dynacolor. Device ID: Set the ID for the video server (1-63). Speed (only applicable if speed domes are used): Adjust the speed of the speed dome (1-10). Port mode: Select RS-485, RS-232 or PTZ.
User Manual SVS-3001 2.5 Event Under the tab , there are submenus including: , , and . 2.5.1 Event server The event setting can be found under the path: Event > Event server Add FTP: Name: Name the FTP server. Network address: Enter the network address of the FTP server. Upload path: Enter the desired upload path for events. Login information: Enter the user name and the password for the FTP server.
User Manual SVS-3001 Add HTTP: Name: Enter the name of the HTTP server. URL: Enter the network address of the HTTP server. User name / password: Enter the user name and the password for the HTTP server.
User Manual SVS-3001 2.5.2 Motion detection The motion detection setting can be found under the path: Event > Motion detection. To create a motion detection area, follow these steps: 1. Click on “Add” to set-up a detection area. 2. Give a name to this window area. 3. Select the trigger level and the sensitivity level for this detection window (0-100). 4. Select a color for the detection window by clicking on the color palette. 5. Click in the picture and drag the mouse to create a motion detection window.
User Manual SVS-3001 2.5.3 I/O ports The I/O port setting can be found under the path: Event > I/O ports. This video server supports 2 photo-coupled relay inputs and 1 relay output.
User Manual SVS-3001 2.5.4 Event configuration The event configuration setting can be found under the path: Event > Event configuration. To add an event trigger, follow these steps: 1. Click on “Add” and the setup panel will be expanded (as shown above). 2. Give a name to this event. 3. Set the time interval between the triggers. 4. Set the time period for the trigger. Choose “Always” or “During time between” or “Never”. 5. Triggered by: Select “motion detection” from the drop-down menu. 6.
User Manual SVS-3001 2.6 Schedule Under the tab , there are submenus including: and . 2.6.1 General The schedule setting can be found under the path: Schedule > General. Follow the steps below on how to set a schedule: 1. Check the “Enabled” box. 2. Select the video stream to be recorded. 3. Define the size of each sliced file (MB). 4. Define the day of the week and the time (by hour of the day) of the scheduled period to be recorded (simply click into the respective field).
User Manual SVS-3001 2.6.2 Storage The schedule setting can be found under the path: Schedule > Storage. Here, information on the storage status is displayed. A message is displayed when a recording is currently running. Note: The USB storage device must not be removed from the USB port during the recording process.
User Manual SVS-3001 2.7 Network Under the tab , there are submenus including: , , and . 2.7.1 General The network setting can be found under the path: Network > General. On this page, the IP configuration is displayed including DHCP and static IP setting. “Enable ARP/ping” enables the camera to accept ARP or ping packets from the network. Disabling this option may provide extra security from intentional ping. The default IP address is 192.168.1.
User Manual SVS-3001 2.7.2 Advanced The network setting can be found under the path: Network > Advanced. NTP configuration: Users may configure a NTP (Network Time Protocol) server so that the camera’s system date and time can be synchronized with a specified time server or DHCP server. HTTP setting: Users may set the HTTP port that will be applied for web access. Default port = 80. RTSP setting: Users may set the RTSP (video) port for video data transmission. Default port = 554.
User Manual SVS-3001 2.7.3 SMTP (e-mail) The network setting can be found under the path: Network > SNTP (e-mail). Configure an e-mail host for the camera which will send e-mails on behalf of the configured e-mail account to a specified mail address (also see the chapter “2.5.4 Event configuration”). Fill-in the information about the mail server, server port, authentication information (if required) and the sender’s e-mail address.
User Manual SVS-3001 2.7.4 DDNS Check the box “DDNS enable” for dynamic DNS configuration. Host name: Assigned name that will be used for accessing the video server. User name / password: Account authentication for logging on to this service. Update time: Periodically, the camera updates its access information in the defined time. Response: The video server responds to the connection information (yes or no).
User Manual SVS-3001 2.8 System Under the tab , there are submenus including: , , , and . 2.8.1 Information The system setting can be found under the path: System > Information. On this page, a list of system and network configuration is displayed. These data are for information only and cannot be changed on this page.
User Manual SVS-3001 2.8.2 User Check the box “Enable anonymous login” if you don’t wish to have a user name displayed. 2.8.3 Date & time On this page, users may configure the system date and time as well as synchronization options with a PC and NTP server.
User Manual SVS-3001 2.8.4 Server maintenance This page provides some tools for system maintenance, such as firmware information and upgrades, backup and upload settings. 2.8.5 Log service Most system operations and/or processes will be kept in a log system. The link provides the review of these records.
User Manual SVS-3001 Appendix: Install UPnP components For Windows XP: Please proceed as follows to install UPnP for Windows XP: 1. Go to , then click on klicken dann auf and double-click on . 2. Click on . 3. Click on . 4. In the Windows wizard window, click on > and then on . 5. Select and confirm with . 6. Click on . 7.
User Manual SVS-3001 Notes: _________________________________________________________________________________ - 38 -
User Manual SVS-3001 Notes: _________________________________________________________________________________ - 39 -
Your local distributor: __________________________________________________________________________ www.santec-video.
