Operation Manual

19
NOTE:
If a channel with no broadcast is selected, the
sound will automatically be muted.
It may take a few seconds for a digital channel
picture to appear on screen after being selected.
To select the video input source
Press INPUT SELECT, then press ▲/▼ or
corresponding Number buttons (0-6) to view a
signal from another device connected to your LCD
TV, such as a VCR or DVD player. You can select TV,
Video1, Video2, Component, HDMI1, HDMI2 or PC
depending on which input jacks you used to connect
your devices.
Source Selection
1.Video1
2.Video2
3.Component
4.HDMI1
5.HDMI2
6.PC
[0-6]:Select
0.TV
CH + / -
Press and release CH + / - . The channel
automatically stops at the next channel set into
memory.
For proper operation, before selecting channels, they
should be set into the memory. See “Memorizing
channels” on pages 17 and 18.
DISPLAY
Press DISPLAY to display the current information on
the screen.
When the TV receives a digital signal, the digital
information will appear.
62-001 HDTV Moving Picture1
CH-1
Digital Cable
No Program Information is available
Sleep Timer
Off
English
Full
1080i
Channel number • Station name
Channel label (if preset) • Broadcast program name
V-Chip rating • Signal type
Sleep timer • Audio language
Program guide • Picture size
Resolution
When the TV receives a analog signal, the analog
information will appear.
•
•
•
•
•
•
14
Analog Cable
Sleep Timer
Off
Full
480i
Channel number • Channel label (if preset)
V-Chip rating • Signal type
Sleep timer •
Audio information (Stereo or SAP)
Picture size • Resolution
Press DISPLAY again to clear the call display.
•
•
•
•
NOTE:
After a few seconds, DISPLAY screen will return to
normal TV-operation automatically.
•
•
•
RECALL
This button allows you to go back to the last channel
selected by pressing RECALL. Press RECALL again
to return to the last channel you were watching.
MUTE
Press MUTE to switch off the sound. The TV’s sound
will be silenced and “Mute” will appear on the screen.
The sound can be switched back on by pressing this
button again or the VOL + or –.
SLEEP
To set the TV to turn off after a preset amount of time,
press SLEEP on the remote control. The clock will
count up 10 minutes for each press of the SLEEP but-
ton (Off, 0h 10m, 0h 20m, ..., 2h 0m). After the sleep
time is programmed, the display will appear briefly
every ten minutes to remind you that the sleep timer
is operating. To confirm the sleep timer setting, press
SLEEP and the remaining time will be displayed for a
few seconds. To cancel the sleep timer, press SLEEP
repeatedly until the display turns to Off.
Sleep Timer
0h 10m
Labeling channels
Channel label appear with the channel number
display each time you turn on the TV, select a
channel, or press DISPLAY.
You can choose any four characters to identify a
channel.
To create channel labels
1
Press MENU, then press ▲ or ▼ to select
“Channel” menu, then press ▶ or ENTER.
2
Press ▲ or ▼ to select “Ch Label”, then
press ▶ or ENTER.
The “Ch Label” menu will appear.
3
Press ◀ or ▶ to select a channel you want to
label, then press ▼.
Ch Label
Label Clear >>
: Adjust
Ch Label
Channel Number 15-1
: Select
4
Press ◀ or ▶ repeatedly until the character you
want appears in the first space.
Label Clear >>
: Adjust
Ch Label
Channel Number 15-1
: Select
Ch Label A
ENTER:Set
The characters rotation as follows:
34D0101A_eng.indd 1934D0101A_eng.indd 19 12/7/07 2:30:17 PM12/7/07 2:30:17 PM