DR201V FM/DAB/DAB+ Stereo Tuner User Guide
Dear Customer Thank you for deciding to purchase this Sansui product. This instruction manual will give you a general idea of how this device operates, as well as providing you with information on safety procedures and cleaning. In order to maintain this product in good condition, and to ensure it’s safe operation, please take a few minutes to read and carefully follow all the safety and operating instructions found in this manual.
Table of Contents 1. INTENDED USE ..................................................................................................................................................... 5 EXPLANATION OF SYMBOLS ..................................................................................................................................................... 5 2. SAFETY INFORMATION ..............................................................................................................................
1. Intended Use This device is a stereo radio tuner capable of receiving FM/VHF, DAB and DAB+ broadcasts. Please adhere to all of the safety information and instructions found in this instruction manual. Explanation of symbols An exclamation mark is intended to inform the user of important information, operation or maintenance instructions, or that special attention is required.
2. Safety Information The following safety and hazard warnings are not only for the protection of your device, but also serve as a protection against potential health hazards. Please take time to read the following instructions carefully. We assume no liability for personal or property damage resulting from the failure to comply with the safety instructions, or from improper operation or handling.
3. Accessories The following accessories are supplied with the system. Please check all these parts are present before proceeding. Please inform your dealer if any part is missing or damaged. 1 x Remote control handset 1 x stereo left and right Phono to Phono cable for connecting to amplifier 1 x DAB wire antenna 1 x mains power cable Page | 7 © Sansui UK 2012 DR201V IB Ver 1.0 Rev 0.
4. Description of parts Front Panel 1 DAB/FM waveband selector. Press to toggle between DAB and FM reception. 2 In DAB mode press this key to activate auto scan function. In FM mode press this key once to activate auto search to next station. Press and hold this for about 2 seconds to auto search previous station. 3 Info button. Press to view DAB station or program information or Radio Data Service (RDS) information in FM mode. 4 Stereo/Mono selector switch.
Display The DR201V has a two line 16 digit display as pictured. The top line of the display shows the current listened to station. When in DAB mode, if the input selector control dial is rotated, the bottom display will scroll through a list of available radio stations. In FM mode RDS data information will be displayed if available. Remote Control Handset 1 DAB/FM SELECTOR button. Press to switch between DAB digital radio and FM analogue radio. 2 PRESET CHANNEL buttons.
- Always follow the manufacturer's instructions when recharging rechargeable batteries. - Touching leaking or damaged batteries could cause skin burns. Use protective gloves suitable for handling such batteries. - Always ensure that the device has been turned off after use. - Always change/replace all batteries at the same time. - If required clean battery and device contacts before inserting, Inserting/changing batteries Remove the battery compartment lid carefully. Remove the used batteries.
5. Setup The DR201V must be connected to an amplifier before any radio stations can be enjoyed. It also needs the supplied antenna or external aerial connected to ensure DAB or FM reception is possible. Connection of Antenna or External Aerial Connection to an Amplifier via RCA Analog Cable Page | 11 © Sansui UK 2012 DR201V IB Ver 1.0 Rev 0.
Connection to an Amplifier via Coaxial Digital Cable Connection to an Amplifier via Optical Digital Cable Page | 12 © Sansui UK 2012 DR201V IB Ver 1.0 Rev 0.
6. RS 232 Interface Specifications and Commands The DR201V is equipped with an RS232 interface to enable control of the unit in a custom installation. Below is the command list for use by your qualified custom install engineer.
7. Troubleshooting and error messages The DR201V is equipped with state-of-the-art technology and is safe to operate. Nevertheless, problems or malfunctions may occur. Before contacting Sansui customer support, refer to the following for possible solutions.
8. Maintenance and handling Carry out a technical safety inspection on a regular basis, e.g. check if the power cable or housing has not been damaged. If there is reason to believe that the device can no longer be operated safely, then disconnect it immediately from the power supply and secure it against any unintentional operation. Carefully remove the power cable plug from the wall outlet and where applicable switch off the corresponding circuit breaker first.
Important Notice Please note that electrical and electronic devices must never be disposed of in regular household waste! Consumers are legally obligated and responsible for the proper disposal of electronic devices by returning them to collection sites designated for the recycling of electrical and electronic equipment waste after the useful life of the device has come to an end.
9. Specifications - Signal to Noise Ratio DAB @2Vp-p, with instrumental 20k LPF enabled. >85dB (A) FM Ultimate signal to noise ratio 98MHz @60dBuV/75KHz Dev. Fmod=1KHz, Amplitude=1.3Vpp Mono >75dB - Total Harmonic Distortion (THD) DAB @2Vp-p with instrumental 20K LPF enabled <0.1% FM 98MHz@60dBuV/75KHz Dev. Mono Fmod=1KHz, Amplitude=1.3Vpp <0.5% - Frequency Range DAB BAND 3: 5A 174.928MHz - 13F 239.200MHz FM 87.
www.sansui.co.uk © Sansui UK 2012 DR201V IB Ver 1.0 Rev 0.
