Quick Guide

380
126
Smart Wireless
Floodlight Camera
Camera Setup
Power on the device, the light will flash once, wait till the indicator
turns red and blinking or a prompt tone is heard.
If the indicator is not red and blinking, press the reset button for
5 seconds then release, the camera would be successfully reset.
Add the device on the app, select Floodlight Camera under Camera&Lock
category.
Follow App's instructions to complete network pairing process,
the device will connect to your Wi-Fi network successfully.
The blue indicator is on, camera is ready for viewing.
Camera Indicator
LED Indicator Status
Red indicator ON
Red indicator blinking
Blue indicator blinking
Blue indicator ON
Camera Status
System starting up
Standby for configuration
Network pairing
Camera online
C21AF001-W0035A12
642
143
226
Operations on App
Settings
Full screen
Listen
Resolution change
Record
Lamp
Talk
alarm
Screenshot
Local Video
Product and Accessories
LED security light
Bar-shaped mounting
plate and 3 screws
Waterproof Gasket
3 Wire connectors
Mounting bolt
Rubber screw cap
Tools Needed
Cross-head screwdriver
Dimensions
1 2 3 4
5 6 7 8
Quick Guide
Warranty & Contact
1-year warranty
Email: [e-mail]
Web: www.sansiled.com
Mfg. date is printed on the Certificate
of Approval
1. This product is suitable for use in wet locations.
2. Do not hang any objects on the product. Mechanical loads may
damage the product.
3. Risk of burns! Do not touch the light source or the housing during
use.
4. Ensure the voltage given on the rating label or in the instruction
manual complies with the power supply.
5. Do not use the product if the parts are damaged, the product
does not work properly or if the product is damaged.
6. Do not stare at the operating light source or direct the beam at
other people or animals, to prevent eye damage.
7. Assemble / install the product according to the intended use and
as described in this manual.
8. Do not assemble / install the product in adverse ambient
conditions or in rooms, where heat sources, hot steam, corrosive
gas, flammable gas, vapors or dust are present.
9. The operating ambient temperature of the product is -25 - +40°C;
store the product and its accessories under -20 - +65°C. Do not use
the product under the conditions with extremely high or low
temperature.
10. Ensure the mounting surface (e. g. wall surface etc.) can load the
weight of the product.
11. Do not assemble / install the product under live conditions.
12. To avoid personal hazard and product damage, keep the
children or pets away from the product and its accessories during
assembly / installation.
13.There are no parts inside the product that can be repaired by the
user.
14. Do not install the product in the electric circuit loop with a
dimmer.
15. If the external flexible cable or cord is damaged, it shall be
exclusively replaced by the manufacturer, the service center or a
qualified specialists to avoid hazards.
16. The light source and the power supply driver of this product are
notreplaceable. When the light source or power supply driver
All parts and accessories are to be found in the packaging. If some
of them are missing, please contact us via [e-mail]
WARNING: If you are not sure how to mount / install the product,consult a local
specialist technician. The wiring installation shall be strictly applied in
compliance with the local regulations,rules and national electrical codes.
Installation
Before installation
1. The product shall be mounted vertically on a flat surface of the wall.
2. Input voltage: local mains supply.
3. Mount the product at a height of 1 - 4 m. The optimal mounting
height is 2.4 m.
WARNING: Switch off the power supply before mounting the product.
NOTE: Find a place to mount the product, where the power line
(live,neutral and earthing) is available.
Step 1： Fixing the mounting plate
1. The bar-shaped mounting plate only matches with the standard
junction box with an installation pitch of 88.9 mm.
2. Make sure the bar-shaped mounting plate is firmly tightened with
the 2 fixing bolts.
Fixing bolt
Earthing connection bolt
Step 2： Wire Connection Black - Live（L）
White - Neutral(N) Green - Ground(PE)
Strip wires 3/8"(9.5mm) if not previously stripped. Hold the BLACK
house wire and the BLACK fixture wire together with ends even. Align
any frayed strands or conductors. Push wires into wire nut and screw
clockwise until two twists are visible in the wires. Repeat above
procedure for both the GREEN or Ground house wire and the Ground
fixture wire.
Step 3： Mounting the product
1. Insert the mounting bolt through the center of the housing and
rear cover.
2. Align the mounting bolt through the center of the sealing gasket
to hold it in place.
3. Align the mounting bolt with the center hole of the bar-shaped
mounting plate.
4. Position the housing and sealing gasket over the junction box.
5. Use a screwdriver to screw the mounting bolt into the mounting
plate, until the product is securely fixed.
6. Fit the rubber screw cap onto the mounting bolt.
App Installation
Search TuyaSmart on App Store or Google Play to get the app, or
you can also scan the QR code below.
Open the app on your smartphone, follow the on-screen instructions
to sign up and log in .
Screenshot
Record
Local Video
Lamp
Alarm
Motion
Photos saved in mobile phone
If need two way audio, please set in
“Settings” -“Basic function settings”
Video saved in mobile phone
Video recorded for motion or full time
Switch on/off lamp manually
Switch for motion detection
PIR motion zone settings
After setting alarm and motion zone, lamp
can be triggered to turn on automatically
if camera is in night vision mode
Enable manually. Can’t be triggered
automatically
Micro SD card
To ensure SD card video recording works fine, we recommend
Class 10 or higher speed Micro SD card.
To make sure the device works normally, please format the SD
card to FAT32 before the first use.
Always power off the device first before inserting or removing
the SD card.
Insert the SD card properly into the slot as below.
Alarm/Motion/Lamp
Talk and Listen
Buzzer
Lamp Head
Motion
Sensor
Lamp Head Transverse
Adjustment Shaft
Lamp Head Longitudinal
Adjustment Shaft
Black to
Black
White to
White
Junction box
ground wire to
green ground
wire from fixture
Reset Button
SD CARD
Standby for configuration
Note: Only 2.4G WiFi is supported.
The network pairing lasts for about 2 mins. If adding failed, make sure the
network is stable and entered WiFi password is correct, re-add the camera.
Note: This App is available on iOS 9.0/Android 4.4 or newer systems.
Red indicator blinking
Safety Warnings
Please take attention that changes or modification not expressly
approved by the party responsible forcompliance could void the
user’s authority to operate the equipment.This device complies
with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
FCC ID：2A4AE-C21AF001
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment.
This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.