Specification Sheet

ManualsBrandsSaniflo ManualsPlumbing ProductSaniCubic 1 1 HP 115-Volt Grinder Pump

SFA Saniflo USA

Sanicubic 1 22 13 29 - 1

SFA Saniflo USA October 2018

105 Newfield Avenue, Suite B

Edison, New Jersey 08837

Toll Free 800-571-8191

Phone 732-225-6070

Fax 732-225-6072

Website www.saniflo.com

Email sfasales@saniflo.com

Guide Specification

Specifier Notes: This guide specification is written in Construction Specifications Institute (CSI) 3-Part

Format in accordance with The CSI Construction Specifications Practice Guide, MasterFormat,

SectionFormat, and PageFormat.

This Section must be carefully reviewed and edited by the Architect to meet the requirements of the

Project and local building code. Coordinate this Section with Conditions of the Contract, Division 01,

other specification sections, and the Drawings. Delete all Specifier Notes after editing this Section.

Section numbers and titles are based on MasterFormat 2018 Edition.

SECTION 22 13 29

SANITARY SEWERAGE PUMPS

Specifier Notes: This Section covers SFA Saniflo USA “Sanicubic 1” packaged simplex grinding

systems capable of discharging wastewater from multiple fixtures from an entire building. The

packaged simplex grinding systems are suitable for above or below ground installation. Consult SFA

Saniflo USA for assistance in editing this Section as required for the Project.

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Packaged simplex grinding systems.

Summary of content (7 pages)

PAGE 1
SFA Saniflo USA 105 Newfield Avenue, Suite B Edison, New Jersey 08837 Toll Free 800-571-8191 Phone 732-225-6070 Fax 732-225-6072 Website www.saniflo.com Email sfasales@saniflo.com October 2018 Guide Specification Specifier Notes: This guide specification is written in Construction Specifications Institute (CSI) 3-Part Format in accordance with The CSI Construction Specifications Practice Guide, MasterFormat, SectionFormat, and PageFormat.
PAGE 2
1.2 RELATED REQUIREMENTS Specifier Notes: Edit the following list of related sections as required for the Project. Limit the list to sections with specific information that the reader might expect to find in this Section, but is specified elsewhere. A. Section 22 05 00 – Common Work Results for Plumbing. B. Section 26 05 00 – Common Work Results for Electrical. 1.3 REFERENCE STANDARDS Specifier Notes: List reference standards used elsewhere in this Section, complete with designations and titles.
PAGE 3
C. Shop Drawings: Submit manufacturer’s shop drawings, indicating dimensions, components, piping, hardware, plumbing connections, and electrical connections. D. Manufacturer’s Certification: Submit manufacturer’s certification that materials comply with specified requirements and are suitable for intended application. E. Operation and Maintenance Data: 1. Submit manufacturer’s operation and maintenance manual, including the following: a. Operation, maintenance, and adjustment instructions. b.
PAGE 4
1.9 A. WARRANTY Warranty Period: 2 years. 1. Additional 1 year warranty period once product registered through manufacturer’s website. PART 2 2.1 A. PRODUCTS MANUFACTURERS Manufacturer: SFA Saniflo USA, 105 Newfield Avenue, Suite B, Edison, New Jersey 08837. Toll Free 800-571-8191. Phone 732-225-6070. Fax 732-225-6072. www.saniflo.com. sfasales@saniflo.com. Specifier Notes: Specify if substitutions will be permitted. B. Substitutions: [Not permitted] [Comply with Division 01]. C.
PAGE 5
8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. Power Supply Cord: SJOW, 3 conductors, 16 AWG, 300 V. a. Length: 80 inches. Noise Level: Less than or equal to 68 dBA (Lp), measured at 3 feet. Discharge Pipe Diameter: 1-1/2 inches. Discharge Rate: a. At 36 feet: 26 gpm. b. At 3 feet: 50 gpm. Maximum Discharge Distance: a. Vertical: 36 feet. b. Horizontal: 328 feet. Discharge at Maximum Height: 26 gpm. Shut-Off Head: 45 feet. Normal Running Time: Depends on number of connected fixtures.
PAGE 6
2.3 ACCESSORIES Specifier Notes: Delete accessories not required. A. 2.4 Descaler: Saniflo liquid descaler/cleanser. SOURCE QUALITY CONTROL A. Factory Test: Test packaged simplex grinding systems to withstand for 1 minute without breakdown, application of 1,000 V AC plus twice the maximum rated voltage between live parts and exposed noncurrent carrying metal parts or power and grounding pins of attachment plug. 1.
PAGE 7
3.4 A. PROTECTION Protect installed packaged simplex grinding systems from damage until Substantial Completion.