User Manual iUSBport2 www.hyperdrive.
FCC STATEMENT 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesirable operation. 2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Sanho Manufacturer's Limited Warranty Sanho warrants to the end user, that this product, excluding content and or software supplied with or on the product, will be free from material defects in manufacture, will conform to Sanho's published product specifications and be fit for normal use during the Warranty Period specified below commencing on the date of purchase provided that the product is legally placed on the market.
Content What's In The Box Charging Battery Battery Management Using iUSBport As USB Charger Using iUSBport As Wireless Storage Access USB Mass Storage Device Before Unplugging USB Mass Storage Device Normal Shutdown Change SSID & Password Connect iUSBport to an existing WiFi network Accessing iUSBport in Mac OS Accessing iUSBport in Windows Standard Network Service List Copy Memory Card To USB H.D.D.
What's In The Box USB Port 1 USB Port 2 WiFi Indicator Charging Indicator MicroSDXC Slot Power Button LCD Charging Port Main Unit Getting Started Guide USB Charging Cable
Charging Battery The product package does not include a USB charger. We recommend that you use a tablet (e.g. iPad) USB charger (5V/2A) to charge the battery. The charging indicator will light up orange during charging. When the battery is fully charged, the charging indicator will turn green. (~6hrs to full charge from empty) Charging Indicator Battery: 3.68V USB Charger (This accessory is not included in the product package.
Battery Management iUSBport can detect a low battery. Once the battery runs low, the red LED will light up and LCD will display a warning message： Low Battery Indicator Warning Message Low Battery After displaying 'Low Battery' for 3 minutes, iUSBport will turn off automatically. To conserve power, iUSBport will turn off automatically if there is no active connection for a specified time. By default, this function is disabled. You can modify this timer from 30 minutes to 120 minutes.
Using iUSBport As USB Charger iUSBport is able to act as a USB charger which can charge a wide range of mobile device. It outputs 5V 1000mA power via two standard USB A Female ports.
Using iUSBport As Wireless Storage Connect device to USB port Press power button and release it when the LCD lights up. Wait for 30 seconds until WiFi indicator is flashing. WiFi SSID Password of Access Point network Go to "Settings" in your WiFi device (e.g. iPad, iPhone) Select "iUSBport" from the list of WiFi networks.
Access USB Mass Storage Device Select "Safari" or any web browser on WiFi device (e.g. iPad, iPhone) Enter 'http://199.0.0.1' in the URL address bar of the web browser. The contents of the USB device will be displayed in the browser. Partition Drives Settings Tip Content We recommend using Safari or Chrome browser as much as possible. Other browsers may not be able to display the full user interface.
Before Unplugging USB Mass Storage Device When device shutdown, unplug USB device Press power button Sync... LCD display "Sync ...
Normal Shutdown Press power button Shutdown? LCD display "Shutdown?" Press power button again Force Shutdown Poke reset button Open side cover
Change SSID & Password Don't forget to change default SSID & password to yours. Otherwise, unauthorized users are able to access your iUSBport and its data. Tap "SSID:" in setup page Input new SSID & password: Tap "Save Change" and reboot iUSBport.
Connect iUSBport to an existing WiFi network If you want your mobile device (e.g. iPad, iPhone, smartphone, tablet, computer etc.) to access iUSBport and the Internet at the same time, you will need to connect iUSBport to an existing WiFi network. This mode is called "Infrastructure Mode". In this mode, you can access iUSBport with your mobile device and remain connected to the Internet at the same time. Wireless Router Tip The default network mode of iUSBport is 'Access Point' mode.
Connect iUSBport to an existing WiFi network Tap "SSID:" in "WLAN Station:" function Choice a WLAN in WLAN list Enter the network password, then click 'Ok' to save the password. If the network password is correct, you will see the wireless router SSID and IP address in setup page.
Accessing iUSBport in Mac OS In the Finder Window, select 'Connect to Server' from the 'Go' menu. Enter the IP address of iUSBport (in the format smb://) in the 'Server Address' text box. ' smb://192.168.0.120 Select 'Guest' and 'Connect' .
Accessing iUSBport in Windows Open 'My Computer' ; My Computer Enter the IP address of iUSBport in the address bar; NOTE! Add two backslash before the IP address! \\192.168.0.120 Click 'Go' or press Enter on the keyboard, and the iUSBport drive will show on the window. \\192.168.0.120 iUSBport-C Click 'iUSBport' to access the contents of iUSBport.
Standard Network Service List There are several standard network servers in iUSBport, such as FTP, DLNA, WebDAV and Samba servers. iUSBport can be accessed by standard FTP, DNLA, WebDAV or Samba client software. FTP and Samba servers support read and write operation if the storage device is 'FAT32' or 'NTFS' formatted . FTP Settings FTP server IP address： 199.0.0.
Copy memory card to USB H.D.D. iUSBport can copy memory card from a USB card reader to a USB hard disk drive (FAT32 formatted). All files including photos and videos can be transferred into H.D.D. automatically. Connect a USB hard disk drive to iUSBport. Wait for a while until LCD display "FS is Ok". If H.D.D. capacity is larger then 1TB, you may need to wait for over 40 seconds. Connect USB card reader with memory card to iUSBport. When LCD display "Copy Card?", press power button once.
Upgrading the Firmware The firmware of iUSBport can be upgraded to add new features and to address any software bugs. Download firmware which should be named IUSBP2.SEF Copy IUSBP2.SEF to the root folder of USB storage device. Insert this USB storage device into iUSBport and it will display the following update message: Update V10 -> V11 ? Press power button once to start updating. Updating... Erasing 19% Erasing flash memory Updating... Writing 77% Writing flash memory Updating...
Specification Model: iUSBport2 USB Port: USB2.0 High Speed 480MBps x 2 Internal Flash: Optional Micro SDXC (Up to 64GB) Wireless: WiFi 802.
iUSBport Designed in Silicon Valley, California by Sanho Corporation All rights reserved. Copyright 2013. Apple, iPad, iPhone are registered trademarks of Apple, Inc.
