H201/H202 中文 GB Revision 1
Features 1. Built-in AM/FM antenna for best reception GB 2. 10 presets (5 each wave band) 3. Water resistant up to JIS7 standard 4. Auto seek stations 5. Large and easy to read LCD display 6. Easy to fix bracket and hanger 7. Battery power indicator 8. Clock 9. Adjustable sleep timer 10. Adjustable short timer 11. Emergency LED illumination (Torch) 12. Emergency Buzzer 13.
Controls LCD Display 2 Preset stations (preset 3 also for tuning step change) 3 Nap timer (Short timer) 4 Power button 5 Band and Time Set button 6 Tuning Control 7 Volume Control 8 Speaker 9 DC IN socket 10 Hanger Ring 11 Emergency Buzzer 12 Torch button 13 Torch 14 Multi Purpose Handle 15 Bracket Holder 16 Battery Cover 17 FM wire antenna compartment 1 GB LCD Display A B C D E F G Battery Power Status Volume level Auto Off status Short Timer set Memory number and seconds Time and Frequency Band indicat
Installing batteries 1. Position the radio face down on a soft surface. 2. Remove the catch as shown and lift out the battery cover. 3. Insert 2 x “D“ size/UM-1/LR20 batteries. 4. Replace the battery cover and catch. 5. Reduced power, distortion, a “stuttering“ sound are all signs that the batteries may need replacing. The batteries should be replaced when the battery indicator flashes and E shows in the display. 6.
Using the AC adaptor (not supplied) 1. Remove the rubber cover of DC in socket on the left hand side of your radio. GB 2. Insert the adaptor plug into the DC socket. 3. Plug the adaptor into mains socket outlet. Whenever the adaptor is used, the batteries are automatically disconnected. The AC adaptor should be disconnected from the mains supply and the radio when not in use. Note: For safety purpose, DO NOT use AC adaptor in the shower room. Use the batteries only. Setting the clock 1.
Operating your radio Your radio is equipped with three tuning methods – Manual Tuning, Search tuning and Memory preset tuning. Manual Tuning 1. Press the Power button to turn on the radio. 2. Select the required waveband by repeatedly pressing the Band button. For FM waveband, pull out and extend the FM wire antenna located in the battery compartment to get best reception. For MW (AM) waveband, rotate the radio for best reception. 3.
Search tuning 1. Press the Power button to turn on the radio. GB 2. Press the Band button to get required waveband, then extend and position telescopic aerial (FM) or rotate the radio (AM). 3. Press and hold down either Tuning up or Tuning down buttons for more than 0.5 seconds to commerce Search tuning. 4. The radio will search and stop automatically when it finds a station of sufficient strength. 5. When the waveband end is reached, the radio will continue tuning from the opposite waveband end . 6.
Memory preset tuning Storing stations in preset memories There are 5 presets for each waveband. 1. Press the Power button to turn on the radio. 2. Tune to the required station using one of the methods previously described. 3. Press and hold down required preset until the radio beeps (more than 2 seconds). The preset number will appear with a M (memory) and the station will be stored under the chosen preset button. 4. Repeat the procedures for the remaining presets. 5.
Recalling preset stations 1. Press the Power button to turn on the radio. GB 2. Select the required waveband by pressing the Band button. 3. Momentarily press the required Preset button, the preset number and station frequency will appear in the display. Software version The software display cannot be altered and is just for your reference. 1. Turn off the radio. 2. Press the Preset button 3/step button for 2 seconds until the software version number (e.g. P01) shown on the display.
Setting Tuning step 3. After the FM range setting is completed, the display will switch to tuning step setting. Press the Tuning up/down button to choose the desired FM tuning step (50 kHz or 100 kHz) and press the Preset button 3/step button to confirm the setting. 4. After the confirmation of FM tuning step, press the Tuning up/down button to choose the desired AM tuning step (9kHz or 10 kHz) and press the Preset button 3/step button to confirm the setting.
Nap timer (short timer) You can set the Nap timer (short timer) either radio is on or off. GB Press Nap timer button , display will appear and flash last nap timer time. Press Tuning up/down button to select required nap timer time, press Nap timer button again to complete setting. Nap timer will start to count by second, display will show and remaining nap timer time (when radio is off). The buzzer will sound for 3 minutes when it reaches the period of time which you have set.
Display backlight The display backlight will be switched on for approximately 15 seconds when any button is pressed. Emergency buzzer To activate Emergency buzzer, press and release Emergency buzzer button . Press and release the button again to switch off the buzzer. Torch Press to release the torch button to turn on the torch. Note: The torch won’t turn off automatically. To turn off the torch, press torch button again.
Bracket You may install the supplied bracket on the wall with the help of the double sides tape back side to hang the radio.
Carrying strap Using the supplied carrying strap, you may hang or carry the radio when not used in bathroom.
Specifications Power requirements Mains via AC adaptor (not supplied) AC 230 volts, 50 Hz or AC 120 volts, 60 Hz ~ only/DC 3V 500 mA GB Batteries: 2 x UM1 (D size, LR20) Battery Life: Approx. 120 hours of listening for 4 hours a day at normal volume using alkaline batteries. Frequency Coverage: FM 87.
