TOOLS REQUIRED Phillips Screwdriver (Not Included) Hammer (Not Included) 2 - People Recommended ASSEMBLY RATING EASY DIFFICULT The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
ASSEMBLY CARE ADVICE FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. Turn clockwise to tighten and only tighten when step is completed or when instructed to do so. Position each part correctly and insert screws or bolts into their respective holes. Use the appropriate hand tools or power tools for assembly. Select steps, such as tightening screws and/or bolts, may require hand tools to avoid causing damage during assembly.
WINE CABINET C E K L J U V PARTS A 1PC F 1PC K 1PC P 1PC U 1PC Z 1PC B 1PC G 1PC L 1PC Q 4PCS V 1PC a 1PC C 1PC H 1PC M 1PC R 1PC W 2PCS b 2PCS N 1PC S 1PC X 1PC c 2PCS O 1PC T 1PC Y 1PC d 4PCS I 1PC D 1PC J 1PC E 1PC ACCESSORIES HARDWARE 1 22PCS 2 22PCS 3 32PCS 4 8PCS 1.25" 7 4PCS 0.5" 13 4PCS 0.75" 8 12PCS 0.53" 9 4PCS 1.32" 10 4PCS 5 8PCS 1.97" 6 2PCS A1 4PCS A2 1PC A3 1PC A4 1PC A5 1PC A6 1SET 0.59" 11 16PCS 12 4PCS 0.71" 0.
GET READY Please group boards as below.
1 Hardware 1 x8PCS Hardware 3 x6PCS 1 1 Accessory A3 x1PC 1 A 1 1 1 3 1 A3 B 1 OPTIONAL Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
2 Hardware 1 x8PCS Hardware 3 x4PCS 3 3 Accessory A3 x1PC A3 G OPTIONAL Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
3 Hardware 1 x4PCS Hardware 10 x4PCS Hardware 11 x8PCS 10 K 10 11 10 11 L 10 HOLE USAGE Align screws with the darkened holes in the above diagram.
4 Hardware 1 x2PCS Hardware 3 x22PCS 3 N Accessory A3 x1PC 3 3 3 O A3 OPTIONAL Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
5 Part C x1PC Part D x1PC Part E x1PC 4 D Front Hardware 4 x4PCS Top 4 E 4 C 4 6 Part F x1PC Part X x1PC Hardware 5 x4PCS Front D Top Accessory A2 x1PC C 5 F or X A2 5 5 RECOMMEND Recommend using a power tool to only tighten hardware (#5) faster. Accessory (#A2) could also work for hardware (#5) if a power tool is not present.
7 Front Part G x1PC Part I x1PC Part J x1PC Top J 2 Hardware 2 x8PCS 2 F 2 2 G 1 2 2 I 2 2 Please refer to page 5 for detailed instructions on how to fasten cam locks (#2) to cam bolts (#1). 2 8 Thin line gap of panel (#I) here. Rotate 90° Part H x1PC Part Y x1PC Front Top Hardware 5 x4PCS Accessory A2 x1PC I J or 5 A2 RECOMMEND Recommend using a power tool to only tighten hardware (#5) faster. Accessory (#A2) could also work for hardware (#5) if a power tool is not present.
9 Front Part c x1PC Part d x4PCS c Top 8 Hardware 8 x4PCS Accessory A2 x1PC d 8 d 8 d 8 d 10 A2 Part V x1PC Part c x1PC Hardware 8 x4PCS Accessory A2 x1PC 8 V c Top 8 8 8 Front
11 Front Hardware 9 x4PCS Top Accessory A1 x4PCS Accessory A2 x1PC c 9 H 9 J A1 A1 9 A1 9 A1 c A2 Lightly tap the end caps until fully inserted.
12 Part A x1PC Part B x1PC Part W x2PCS Front Hardware 2 x8PCS Accessory A2 x1PC Top W B W 1 2 2 2 2 A2 2 X2 A
13 Part a x1PC Part b x2PCS b Hardware 8 x4PCS Accessory A2 x1PC b a 8 8 Front X2 Top 14 Hardware 7 x4PCS Front Top 7 7 X2 A b B b
15 Part N Part O Part P Part Q Front Top x1PC x1PC x1PC x4PCS O Hardware 2 x2PCS Q Q Accessory A3 x1PC Q Q 2 N P 1 A3 2 2 OPTIONAL 16 Front Part M x1PC Hardware 2 x2PCS Top A3 Accessory A3 x1PC OPTIONAL M 2 O Q Q 2 N Q Q
17 Top Front O M N How to Connect Rails 1) Ensure ball bearing on the glides of the side panels are moved to the front of the rail. 2) Align and connect the rails on drawer to the ball bearing of the rails of the side panels. 18 Top Part K x1PC Part L x1PC 11 11 Front Hardware 11 x8PCS HOLE USAGE L K Align screws with the darkened holes in the above diagram. HINGE ADJUSTMENT Depth Adjustment. Length Adjustment.
Part R Part S Part T Part U Part Z x1PC x1PC x1PC x1PC x1PC S Z 2 Top Front 4 R Hardware 2 x2PCS Hardware 4 x4PCS U 4 T 2 1 S 4 2 4 R 20 Hardware 6 x2PCS 6 Fully extend drawer rails then align the rails smallest hole to the drawer slide panels holes. Secure with bolts (#6).
21 Hardware 12 x4PCS Hardware 13 x4PCS 12 13 Y Insert fixative plates (#12) through the thin lined gaps between back and side panels, then secure by using screws (#13). [ No pre-drilled holes ] Top X4 Front 22 Accessory A4 x1PC Accessory A5 x1PC Accessory A6 x1SET A5 A4 A6 Y Top Front For safety, please secure unit onto wall by using wall mounted straps provided. Refer to page 23 on wall mounting guide.
23 ASSEMBLY COMPLETED Please ensure the furniture rests on an even and flat surface. If the produst wobbles or feels loose,double-check all bolts and/or screws are properly tightened and secured. Keep this handy! Please retain this instruction manual and any order-related information for future reference. Lift, dont drag! To avoid damage to product please always LIFT the product when transporting of adjusting the placement.
