Desk THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Easy WARNING ‐ Unit can tip over causing severe injury or death. ‐ Anchor unit to stud in wall (if instructed to). ‐ Do Not allow children to climb on unit. ‐ Put heavy items on lower shelves or drawers.
Helpful Hints PEOPLE NEEDED FOR ASSEMBLY: 2 ESTIMATED ASSEMBLY TIME: 2 HOURS ‐ Open your item in the area you plan to keep it to avoid excessive heavy lifting. ‐ Identify, sort and count the parts before attempting assembly. ‐ Compression dowels are lightly tapped in with a hammer. ‐ Slides are labeled with a R (right) and L (left) for proper placement. ‐ Make sure to always face the point on the top of the Cam Lock towards the outer edge.
Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.
Board Identification Not actual size C B A D E Left Panel Right Panel 020 Left Partition Right Partition Modesty Panel F Top I H G Right Bottom Left Bottom Right Shelf M J K Adjustable Shelf Left Kick L Right Kick 4 Top Rail
Board Identification Not actual size N O Drawer Front S Q P Drawer Back Left Drawer Side T U R Right Drawer Side Drawer Bottom V W File Drawer Front File Drawer Back File Left Drawer Side File Right Drawer Side File Drawer Bottom X Left Door Y Right Door AA Z Left Back Panel 5 Right Back Panel
Board Identification Not actual size F A J M X AA C G I K D B H Y L P O U R W S Q N T Drawer File Drawer 6 V
Part List Actual Size 1 2 (x20) (x20) cam bolt cam lock 4 3 (x20) wood dowel (x50) (x20) (x4) 7/16" pan head 7/16" flat head 1‐1/4" flat head 8 9 7 10 (x4) (x2) (x4) confirmat 5/8" bolt 3/8" bolt 12 13 (x8) drive fastener (x32) nail 6 5 (x4) 1/4" washer 11 (x6) angle bracket 16 (x4) shelf support Not Actual Size 14 (x4) hinge 15a 17 15b (x2) plastic catch 7 (x2) drawer bracket 18 (x4) drawer bracket
Part List Not Actual Size 19a left cabinet member 19b right cabinet member 20 19c 21 left drawer member 19d right drawer member (x2) 19 drawer slide pkg.
STEP 1 1 6 (x8) (x4) 1 1 1 1 1 6 F M 1 1 6 6 1 6 rounded edge of top rail (M) 9 do not over tighten
STEP 2 2 (x12) (x12) 11 4 3 (x2) (x2) Quick Assembly 2 Tip 3 2 2 2 2 H 3 2 2 I 3 3 3 2 3 2 2 G Proper orientation of CAM LOCK 2 3 4 11 2 Angle bracket (11) to be flush with front edge of shelf.
STEP 3 1 (x2) 2 (x2) 3 (x2) 11 4 (x1) (x1) Quick Assembly 1 Tip Proper orientation of CAM LOCK 2 1 A 4 2 3 11 finished edge Angle bracket (11) to be flush with front edge.
STEP 4 1 2 (x2) (x2) (x4) 4 3 5 (x3) (x1) marked with a "R" Quick Assembly 11 Tip 19b right cabinet member (x1) (x1) Proper orientation of CAM LOCK 4 Angle bracket (11) to be flush with front edge.
STEP 5 1 2 3 (x2) (x2) (x2) 11 4 (x3) (x1) Quick Assembly 15a Tip Proper orientation of CAM LOCK (x1) #A30030 1 2 1 C 4 2 11 4 Angle bracket (11) to be flush with front edge.
STEP 6 19a 5 marked with a "L" left cabinet member (x1) (x3) C 5 5 finished edge 5 19a 14
STEP 7 1 2 (x2) (x2) (x4) 5 (x3) (x3) marked with a "L" 15a 11 4 3 19a left cabinet member (x1) (x1) (x1) Quick Tip 4 Angle bracket (11) to be flush with front edge.
STEP 8 5 marked with a "R" right cabinet member (x1) (x3) 19b D 5 5 finished edge 5 19b 16
STEP 9 UNLOCK LOCK Attach left bottom (G) to the left panel (A) as shown. Next, attach left partition (C) to left bottom (G) as shown.
STEP 10 UNLOCK LOCK Attach right bottom (H) and right shelf (I) to the right panel (B) as shown. Next, attach right partition (D) to right bottom (H) and right shelf (I) as shown.
STEP 11 UNLOCK LOCK H With the help of another person, position the top (F) as shown. Attach component from step 10 onto the top (F) as shown.
STEP 12 7 (x2) D F E raw surface 7 20
STEP 13 7 (x2) UNLOCK With the help of another person, attach component from step 9 onto the top (F) as shown. Then attach the modesty panel (E) to the left partition (C) with two confirmat screws (7).
STEP 14 4 (x6) 4 Edge of kick (K) and edges of panels (A&C) to be flush. K 4 G Side edge of kick to be flush with this surface. Edge of kick (L) and edges of panels (B&D) to be flush.
STEP 15 IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT AND MUST BE INSTALLED PROPERLY. 13 Using nails (13), attach each back panel as shown. Place edge onto top (F), align squarely with vertical panels and nail straight into back edges as shown.
STEP 16 With the help of another person, stand the unit upright.
STEP 17 18 (x4) Lay the drawer sides (U&V) down on a flat hard surface. Carefully line up the drawer bracket with the holes in the drawer sides as shown. Using a hammer, tap each drawer bracket stem part way into the hole. Repeat process until the drawer bracket is fully seated on the drawer side.
STEP 18 4 (x8) Be sure the groove in the drawer sides are centered in the groove of the file drawer front (S).
STEP 19 finished surface W V U S 27
STEP 20 12 (x4) You will need to tap the drive fasteners (12) lightly with a hammer to securely fasten.
STEP 21 5 19c marked with a "L" left drawer member (x4) 19d marked with a "R" right drawer member (x1) #A56750 5 19d 5 V 5 U 5 19c 29
STEP 22 17 (x2) Lay the drawer sides (P&Q) down on a flat hard surface. Carefully line up the drawer bracket with the holes in the drawer sides as shown. Using a hammer, tap each drawer bracket stem part way into the hole. Repeat process until the drawer bracket is fully seated on the drawer side.
STEP 23 4 (x4) Be sure the groove in the drawer sides are centered in the groove of the drawer front (N).
STEP 24 Q R finished surface N P 32
STEP 25 12 (x4) 12 You will need to tap the drive fasteners (12) lightly with a hammer to securely fasten.
STEP 26 8 marked with a "L" 19c left drawer member marked with a "R" 5 19d (x4) 21 right drawer member (x1) (x2) (x1) 19d 5 Attach the slides first then the handle.
STEP 27 4 24 (x1) (x2) Attach the drawer brace (24) to the bottom side of the drawer as shown with two screws (4).
STEP 28 4 (x12) 9 10 (x4) (x4) 15b 14 (x4) 21 (x2) (x2) 4 4 14 15b 9 10 10 14 X 9 10 10 Y 14 21 4 14 14 36
STEP 29 4 (x8) Mount the left and right doors (X&Y) as shown with screws (4). Please note, the hinges and plastic catches can be adjusted by loosening the screws, making needed adjustments and retightening screws. 4 X Edge of door to be flush with surface of partition. (Same for other door.
STEP 30 22 20 16 (x2) (x4) 23 (x1) (x1) Note: The drawer bracket holes are slotted. Drawer fronts can be adjusted by loosening screws, making needed adjustments and retightening screws. 23 22 J N 16 cabinet member roller S roller drawer runner Plastic file holders (20) have been supplied if using your drawer for hanging folders.
Maximum Loads This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. 10 lbs 4.5 kg 20 lbs 9.1 kg 100 lbs 45.3 kg 20 lbs 9.1 kg 20 lbs 9.1 kg 25 lbs 11.3 kg Warning: Risk of injury to persons ‐ do not place a television on this furniture. This furniture is not approved for use with a television. Certificate of Conformity 1. This certificate applies to the Dorel Home Furnishings, Inc.
Español Cubierta Delantera Este libro de instrucciones contiene información IMPORTANTE de seguridad. Por favor lea y manténgalo para referencia en el futuro. No Regrese este producto! Comuniquese con nuestro amistoso equipo de servicio al cliente para obtener ayuda. PRECAUCION Este mueble puede volcarse y causar graves heridas y/o muerte. Anclar el mueble a un poste de madera en la pared (si esto se requiere). No Permita que los niños monten el mueble.
Español Página 10 El soporte del ángulo (11) debe estar alineado con el borde frontal. Página 11 El soporte del ángulo (11) debe estar alineado con el borde frontal. Página 12 El soporte del ángulo (11) debe estar alineado con el borde frontal. Página 13 El soporte del ángulo (11) debe estar alineado con el borde frontal. Página 15 El soporte del ángulo (11) debe estar alineado con el borde frontal. Página 17 Acoplar la parte inferior izquierda (G) al panel izquierdo (A) como se muestra.
Español Página 23 ¡IMPORTANTE! EL PANEL TRASERO ES UNA PARTE ESTRUCTURAL DE ESTA UNIDAD Y DEBE ESTAR INSTALADO CORRECTAMENTE. Con clavos (13), acoplar cada panel trasero como se muestra. Colocar el borde sobre la parte superior (F), encuadrado con los paneles verticales y clavar en los bordes traseros como se muestra. Página 24 Con ayuda de otra persona, poner la unidad recta. Página 25 Apoyar el cajón de costado (U&V) en una superficie plana estable.
Español Página 37 Montar las puertas izquierda y derecha (X&Y) como se muestra con tornillos (4). Tener presente que las bisagras y las agarraderas de plástico pueden ajustarse desaflojando los tornillos, haciendo los ajustes necesarios y reajustando los tornillos. Borde de puerta a ras con superficie de tabique. (Lo mismo para la otra puerta). Página 38 Aclaración: Los agujeros del soporte del cajón están ranurados.
Français Couverture Avant CE LIVRET D'INSTRUCTION CONTIENT DES INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ. VEUILLEZ LIRE ET GARDER POUR UNE RÉFÉRENCE FUTURE ATTENTION Le meuble peut basculer et causer des blessures graves ou la mort. Ancrer le meuble à une planche murale dans le mur (si indiqué). Ne laissez pas les enfants grimper sur le meuble. Placez les articles lourds sur les étagères ou dans les tiroirs inférieurs.
Français Page 10 Équerre de fixation (11) à aligner avec le bord avant. Page 11 Équerre de fixation (11) à aligner avec le bord avant. Page 12 Équerre de fixation (11) à aligner avec le bord avant. Page 13 Équerre de fixation (11) à aligner avec le bord avant. Page 15 Équerre de fixation (11) à aligner avec le bord avant. Page 17 Fixez le fond gauche (G) au panneau gauche (A) comme indiqué. Ensuite, fixez la cloison gauche (C) au fond gauche (G) comme indiqué.
Français Page 24 Avec l'aide d'une autre personne, mettez le meuble debout. Page 25 Posez les bords du tiroir (U et V) sur une surface plate dure. Alignez soigneusement le support du tiroir avec les trous dans les côtés du tiroir, comme indiqué. En utilisant un marteau, enfoncez bien chaque cheville de support du tiroir dans leur trou. Répétez le processus jusqu'à ce que le support du tiroir soit pleinement placé sur le côté du tiroir.
Français Page 38 Remarque : les trous du support du tiroir sont surdimensionnés. Les devants de tiroir peuvent être ajustés en desserrant les vis, en faisant les ajustements requis, puis en resserrant les vis. Les supports de dossiers en plastique (20) ont été fournis si vous utilisez votre tiroir pour accrocher des fichiers. Page 39 CHARGES MAXIMALES Ce meuble a été conçu pour supporter les charges maximales indiquées.
