Assembly Instruction Sheet

ManualsBrandsSand & Stable ManualsLightingYeles 2 - Bulb Seeded Glass Outdoor Flush Mount

(2)A19MediumBaseBulbs60WMaximumor

(2)MediumBaseVintageBulbsarerecommendedbutnotsupplied.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

1of2

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar

Assembly

Glass Shade

Cage

Fixture Body

Tab

STEP 1 Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of

the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Remove the mounting ball from the Crossbar Assembly (A). Adjust

the hex nut and lock washer underside of the crossbar to the middle

of the nipple.

C. Place the ceiling canopy and the Fixture Body (C) over the nipple

against the ceiling to determine the correct position of the nipple.

Thread the mounting ball back onto the nipple. Adjust the nipple to

allow the ceiling canopy and the Fixture Body (C) to rest against the

Outlet Box

Green

Ground Screw

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Mounting Ball

Figure 1

(Step 1 Continued)

ceiling when held in place by the mounting ball.

D. Remove the mounting ball and the Fixture Body (C). Tighten the lock

washer and the hex nut against the crossbar to secure in place.

STEP 2 - Wire Connections

A. Wrap bare or green ground wire around green ground screw on the

crossbar, no less than 2 inches from the end of the wire. Tighten the

green ground screw.

B. Use standard wire connectors (not included) to make all wire

connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

Figure 2

Green Ground Screw

on the Crossbar

White wire

from outlet box

White wire

from fixture

Black wire from

outlet box (or Red)

Black wire

from fixture

Bare, or Green

Ground wire

from outlet box

Ground wire

from Fixture

STEP 3 Install Fixture Body-

A. Place the Fixture Body (C) over the end of the nipple and secure with

previously removed mounting ball. Hand tighten until snug.

Outlet Box

Mounting Ball

Nipple

Figure 3

Assembly Instruction Sheet

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (2) A19 Medium Base Bulbs 60W Maximum or (2) Medium Base Vintage Bulbs are recommended but not supplied. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
STEP 4 - Install Bulbs, Glass Shade and Cage A. Remove lock balls from the Fixture Body (C). B. Insert bulbs onto sockets and screw snugly into place. C. Place the Glass Shade (D) into the Cage (E) and secure by pushing Tabs (B) onto top edge of the Glass Shade (D) and the Cage (E). D. Lift the Cage with Glass Shade upward and pass the holes on the Cage (E) over the bolts on the Fixture Body (C). Secure by threading previously removed lock balls back onto bolts. Hand tighten until snug.