ASSEMBLY INSTRUCTION 309BT TWIN BED 309BF FULL BED A B Headboard C Headboard Post Footboard AR AL BL 1pc D E Slat H Side Rail Drawer Back 2pcs Slat Support Leg 2pcs Drawer Back Support I Drawer Side Support IL K Left Drawer Side L Right Drawer Side 2pcs 2pcs N IR 4pcs 1pc 2pcs M F GR 2pcs Drawer Front Slat Center Rail 1pc GL J 1pc 2pcs 1set (13pcs) G BR Drawer Bottom O Drawer Bottom Support 2pcs 2pcs 1
P Drawer Support Leg Q R Dust Cover Cam Bolt 6.5mm x 35mm 2pcs S V Y AB Cam Lock 1pc T 24pcs U Dowel JCBC Bolt 15mm x 12mm Ø8 x 25mm M6 x 30mm 24pcs 16pcs 5pcs JCBC Bolt W X Drawer Slide JCBB Bolt M6 x 50mm 350mm M8 x 20mm 2pcs 2pcs 16pcs JCBB Bolt Z Spring Washer AA Flat Washer M8 x 40mm M8 M8 6pcs 6pcs 6pcs Handle 2pcs AC AD PH CBS M4 x 20mm M3.
AE AH CBS AF AG CBS Allen Key M4 x 38mm M4 x 30mm M4 8pcs 26pcs 1pc Allen Key AI AJ Adjustable Glider Adjustable Glider M5 M6 (Ø23) M6 (Ø16) 1pc 2pcs 2pcs These pages lists all the content included in the box. Please take the time to identify the hardware as well as the individual components to this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. IMPORTANT NOTE : 1.
1 (i) Attach Adjustable Glider (AI) to Slat Support Leg (F) and Adjustable Glider (AJ) to Drawer Support Leg (P). (ii) Attach Cam Bolt (R) to Drawer Back Support (H) holes as image below and tighten with screwdriver (not provided). F R x2 P x2 R R H AJ 2 AI Attach Cam Bolt (R) to Footboard (C) holes as image below and tighten with screwdriver (not provided).
3 (i) Attach Drawer Support Leg (P) to Drawer Back Support (H) and insert JCBC (U) to the holes and tighten using Allen Key (AG). (ii) Insert Cam Lock (S) and Dowel (T) to Drawer Side Support L & R (I) holes. S AG I Rx2 S U U H S U T T P T S I L x2 T P 4 (i) Attach Cam Bolt (R) to Drawer Front (J) holes. (ii) Attach Drawer Slide (W) to Drawer Side Support L & R (I) and insert CBS (AD) to the holes and tighten.
5 (i) Insert Cam Lock (S) to the holes of Left Drawer Side (K), Right Drawer Side (L) and Drawer Bottom Support (O) properly. (ii) Attach Drawer Slider (W) to Left Drawer Side (K) and Right Drawer Side (L) and insert CBS (AD) to the holes and tighten. (iii) Attach Cam Bolt (R) to Drawer Back (M) holes as image below and tighten with screwdriver (not provided).
(i) Attach Side Rail L&R (G) to Headboard (A) and Footboard (C) by inserting JCBB (X) loosely into provided holes. (ii) Hook Side Rail’s brackets on as shown and tighten all bolts using Allen Key (AH). A X x16 AH G G C 8 Attach Drawer Back Support (H) with Drawer Support Leg (P) to Drawer Side Support L&R (I) with right face and tighten.
9 Spread the Slat (D) with bottom facing up. Place Slat Center Rail (E) and Slat Support Leg (F) on top of Slat (D). (ii) Please notice on FACING HEADBOARD sticker on Slat (D) to match on Slat Center Rail (E). (iii) From bottom of Slat (D) insert JCBC (V) to the holes and tighten using Allen Key (AG). (i) F D D FACING HEADBOARD FACING HEADBOARD E V x2 AG 10 (i) Attach Slats with Legs to top of Twin Bed / Full Bed properly and insert JCBC (U) to the holes and tighten using Allen Key (AG).
11 Attach Left Drawer Side (K) and Right Drawer Side (L) to Drawer Front (J) and fully tighten. K L 12 x2 J Attach Drawer Bottom Support (O) to Drawer Front (J) and fully tighten.
13 Slide in Drawer Bottom (N) to Left Drawer Side (K) and Right Drawer Side (L) groove. N K x2 L 14 (i) Attach Drawer Back (M) to Left Drawer Side (K) and Left Drawer Side (L) and insert CBS (AE) to the holes and fully tighten. (ii) Lock Drawer Bottom Support (O) tightly.
15 Attach Handle (AB) to Drawer Front (J) and insert PH (AC) to holes and tighten. AB x2 AC 16 Slide in Drawer Box Sets properly as image below.
17 Attach Dust Cover (Q) and CBS (AD) to the top of Slats and Drawer area and fully tighten. AD AD Q Cleaning & Care Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may loosen over time. Periodically check that all connections are tight.
