SANCTUARY, HOME & OFFICE SECURITY VAULTS INSTRUCTION MANUAL FOR SA-PVIS & SA-PV2S IMPORTANT: Please read this Information and follow all safety rules carefully before ‘operating your gun safe. Failure to do so will void your warranty.
TABLE OF CONTENTS IMPORTANT INFORMATION 1. REGISTRATION 2. UNDERSTANDING YOUR VAULT 3. INITIAL ENTRY... 4. BATTERY INSTALLATION 5, ELECTRONIC LOCK SECURITY CODE SETUP 6. LOW BATTERY WARNING 7. SILENT ENTRY MODE 8. LOCKOUT MODE/TAMPER PROTECTION 5. LOCKED OUT OF YOUR VAULT . 10. PROPER PLACEMENT AND MOVING OF VAULT. 11.
DISCLAIMER READ BEFORE VAULT SETUP PLEASE READ THIS INFORMATION CAREFULLY BEFORE OPERATING YOUR SANCTUARY VAULT. DO NOT LOCK THIS MANUAL OR THE BACKUP KEYS IN YOUR VAULT. » Thank you for choosing a Sanctuary vault to protect your valuables. We are committed to securing, organizing and protecting your most important documents, valuables and keepsakes. + If you experience problems or challenges with your vault, please contact us. Many issues can be quickly resolved without the product being returned.
1. REGISTRATION By registering your Sanctuary vault we will be able to expedite and address any problems or challenges you may have which would otherwise require a notary letter and proof of payment. REGISTRATION INFORMATION The information you record onto this page will be required in the event you cannot access the contents of your Sanctuary vault. Please fill out all the required information below and retain for your records and safe keeping.
2.
3. INITIAL ENTRY 1. Locate the key cover on the lock face and remove carefully by pulling the key cover tab. In the future you may place flat head screw driver in the slot and pry upwards. LOCK UNDER KEY COVER ~ Insert and turn the key counterclockwise. Hold the key In the fully turned position while rotating the knob clockwise to grant access to your vault. 4. BATTERY INSTALLATION ‘WARNING: The batteries must be inserted with the correct polarity.
5. ELECTRONIC LOCK SECURITY CODE SETUP Important: Your vault comes with a factory preset code of 1234. It is necessary to re-program your vault with a new security code you have personally selected to provide maximum security. Be careful, in choosing your new security code, you'll want to be sure that you can operate the unit quickly without making an error. 1. First, remove the black rubber plug that covers the reset button on the door panel. 2. Use a pen tip to press the reset button.
6. LOW BATTERY WARN NG This electronic lock is equipped you when the batteries are low by illuminating the blue light {cent on the keypad for 10 seconds any time the keypad is activated. 7. SILENT ENTRY MODE to alert r) Blue = Low Battery By activating the silent entry mode, the vault will no longer make audible sounds. To turn on silent entry mode, press and hold the button for {3) econ The green light will flash twice ds. indicating the vault is now in silent entry mode.
8. LOCKOUT MODE / TAMPER PROTECTION 0 1. Three consecutive incorrect code entries will put the vault in “Basic Lockout” mode. Touch pad is deactivated for 30 seconds. 138) 2. After “Basic Lockout” mode has ended, another three consecutive incorrect code entries will result in “Severe Lockout” mode. Touch pad Is deactivated for 5-minutes. 9. LOCKED OUT OF YOUR VAULT In the event you have forgotten the security code your primary action will be to use your backup keys in order to gain access to your vault.
1. SECURING YOUR VAULT 1. A security cable Is included with your vault. To secure the cable around a fixed object, first loop the cable around the object as shown in the figure to the right. 2. Insert the cable’s metal peg end into the hole on the side of the vault while still open. 3. From the inside of the vault, take the cable clip and push it over the metal peg until fully secured. Use pliers to seat the cable clip if needed.
11. SECURING YOUR VAULT (CONTINUED) TOOLS AND HARDWARE NEEDED TO SECURE «DRILL © 2 STEEL LAG BOLTS {NOT INCLUDED} SIZE 1/4" X 1.50" TO 2.0° LONG 3/8" DRILL BIT © 2 STEEL WASHERS {NOT INCLUDED} 1/4" {FOR DRILLING ANCHOR HOLE ) © 2 PLASTIC ANCHORS {NOT INCLUDED}SIZE $10-12 X 1.5" TO 1.
SA Consumer Products will repair or replace, at their sole discretion, any Sanctuary vault damaged by fire, forced entry, forced attack or natural flood for the lifetime of the original owner. SA Consumer Products will repair or replace, at their sole discretion, any Sanctuary vault with defective parts, paint or lock for three years of the original owner purchase date.
