SANAV GPS Tracker Utility Setup Guide Revision: 1.0.
1. Notification ..................................................................................................................3 1.1 1.2 1.3 1.4 Introduction:......................................................................................3 Disclaimer............................................................................................3 Copyright..............................................................................................3 Document Amendments.................................
1. Notification 1.1 Introduction: This User Manual details how to make the connection from SANAV MU-201 Nano Tracker to your PC. It also details all the features and configuration of GPS Tracker Utility. If you have any problem with the content in this manual, please contact SANAV Customer Service by e-mail jacky.sun@sanav.com. 1.2 Disclaimer This document, and all other related products, such as device, firmware, and software, is developed by SAN JOSE TECHNOLOGY INC. thoroughly.
1.4 Document Amendments Revision Date GPS Tracker Utility Version Comments 1.0.1 2012/7/17 V1.01 Optimized for MU-201, MU-58 1.0.2 2013/8/1 V1.02 Modify schedule function :To enable/disable all the stages of schedule.
2. Installation 2.1 Connect the device to your PC 1. Install the USB Driver and the GPS tracker Utility in the CD. 2. Turn on MU-201 before connecting it to a PC. 3. Plug in the AP Cable (connect USB to PC and Mini USB to MU201). 4.
2.2 Start up GPS Tracker Utility 4. The main screen of GPS Tracker Utility (MU Series). 5. Execute GPS Tracker Utility. Click on “Port” and select the Comm Port then Connect 6.
3. Setting Function 3.1 User Settings: Username: At the maximum of 16 letters. (Letters have to be “a~z, A~Z, 0~9, @ - /”) Pin Code: 4 digits of number to enable SIM service Password: 4 digits of number Phone Book: 3 sets of phone number. Max: 19 digits SOS Phone: 1 set of phone number, Max.19 digits Note that both adding and not adding the “+ “sign in front of the cellular phone number(s) are both acceptable, while the”+” sign should precede the national code. 3.1.
3.2 GPRS Settings： ： Route : Representation Router code 0 HTTP/SMS, send data to URL, if the URL is untouchable, then send it via SMS instead. 2 HTTP only, send data to URL, if the URL is untouchable, it won’t send the data by SMS. 4 SMS only, send data by SMS only. 6 TCP/SMS, send data to an assigned IP address, if the IP is untouchable, then send it via SMS instead. 7 TCP Only, only send data to an assigned IP address.
3.3 Mode Setting： ： Field Descriptions Range (0~1): Auto answer.
Charger in Auto ON Power Key The device automatically turns ON 0: Off when plugging in charging cable 1:On with power source. To enable or disable power button 0: Off function. 1:On The language type of Google map En-us, zh-tw,ar-AE…etc.
3.4 Report Settings 3.4.1 Auto Report Field Descriptions Range Report time interval Report Note* the numbers will be rounded to the next Time A constant interval of Interval Unit automatically; you can put the number in the sending data preferred column of Time Units. 0~9999, where 0 means Total turning off the Auto Amount of report Report Report and 9999 means infinite The distance interval when reporting by distance.
3.4.2 Over Speed Settings Field Descriptions Range Over 0: Off Speed Over Speed Detection ON/OFF 1:On Decect Speeding On Speed Limit of Over Speed Event 1~65000 km/h The report interval when Over Speed. 1~65000 in seconds Threshold Report Interval Total 1~9999, 9999 means Amount of report Report infinite 3.4.3 Panic Field Descriptions Range Tick the “Panic” and the tracker will send report Report when the “SOS” is pressed.
3.4.6 Report Tail Field Descriptions Range By enabling “Tail Report”, there will be additional information included in each report 0: Off Report Tail data. The additional data including RSSI, 1: On vibration sensor status, report number, charger status, and Cell ID information.
3.5 Geofence Settings Field Descriptions Range Lat. Latitude dd.dddddd Long. Longitude ddd.
3.
3.7 Power Settings Field Descriptions Range User can use the command to set up the ON power on/off schedule per day of the ON: Power ON device. OFF: Power OFF There are totally 4 stages of a day can be scheduled.
4. Button Function Save: To save the setting that has been done. After saving the setting, reboot the MU-201 in order to restore the new setting. Load: To view the current settings. Default: All parameters returned to default Save File: Save the current setting as a file Load File: Load previous file of setting.
5. FAQ Please turn ON MU-201 before connecting to PC. Please check if you have installed USB Driver. Please check the correct COM Port in Device Manager Not in command mode (Windows) Please make sure you used the correct USB Data Cable (Not the charging Cable.
