MARINE DSC VHF RADIO TELEPHONE FOR GMDSS OPERATING MANUAL STR- 6000A SAMYUNGENC CO.,LTD.
INSTRUCTIONS Please read this operating manual with care before turning on power. 1. How to transmit and stop Distress Call In performing Distress Call function, press button and hold it down for 3(three) seconds until DISTRESS MESSAGE is seen. Then the whole display unit will start flashing with a strong alarm. In transmitting Distress Call, the transmission must be made based on the judgment of a person on duty.
2-1 How to check out power supply Input voltage in VHF main unit: Confirm that DC13.6V is supplied. 2-2 How to transmit and receive DSC In order to use DSC function, make sure that any MMSI number available must be input first. 3. Other instructions 3-1 In using Semi-Auto & Auto connection service with DSC, it is necessary to check with the concerned authorities about the formalities of call charge because the billing system has not yet been decided worldwide.
Chapter 1. Introduction .................................................................................... 6 1.1. Introduction ....................................................................................................... 6 1.2. Features ............................................................................................................ 6 Chapter 2. Configuration ................................................................................. 8 2.1. Standards............................
4.5. DIGITAL SELECTIVE CALLING (DSC) .......................................................... 27 4.5.1. Configuration of CALL Screen ............................................................... 29 4.5.2. CALL Menu Description and Instruction ................................................ 29 4.5.2.1. DISTRESS CALL(Distress message SETUP and Call) ............... 30 4.5.2.2. ALL SHIPS MESSAGE SETUP AND CALL................................. 32 4.5.2.3. INDIVIDUAL MESSAGE SETUP AND CALL..................
Chapter 1. Introduction 1.1. Introduction STR-6000A includes DSC/VHF radio telephone and DSC receiver required by the Global Maritime Distress and Safety System(GMDSS) and is designed to be compact and lightweight for easy installation in any vessels engaged in international voyages and near-going vessels. In addition to the conventional voice communication, STR-6000A is equipped with Digital Selective Calling(DSC) functions for distress calls and routine calls as well.
Such functions as TAG CHANNEL SCANNING, ALL CHANNEL SCANNING, GROUP-CHANNEL SCANNING and DUAL WATCH allow user to listen to any specific channel. Besides the existing voice communications, it is available to work on communications for distress, urgency, safety and other routines as well by using DSC function.
Chapter 2. Configuration The equipment consists of as follows;. 2.1. Standards Name Model Quantity Remarks VHF Radio Main Unit STR-6000A 1 Set Including HAND MIC Operating Manual 1 Lot 2.2.
Chapter 3. Specifications 3.1. STR-6000A Standards TX Frequency RX Frequency Number of Channels Radio Wave Mode Channel Interval Communication Mode Antenna impedance Audio Output Impedance Frequency Stability Voltage Supply Consumption Currency (13.6V) Operating Temperature Dimensions Weight 156.025MHz ~ 157.425MHz 156.050MHz ~ 163.
3.3. Receiving Unit Receive System Intermediate Frequencies Audio Frequency Response Double Conversation Super Heterodyne 1st 21.7MHz 2nd 450kHz Receiving Frequency - 21.7MHz SYNTHESIZER Mode 32uV (20dB SINAD) 0.22uV (12dB SINAD) -6dB/octave Squelch Sensitivity Co-Channel Rejection Adjacent Channel Selectivity Spurious Response Rejection Ratio Inter-modulation Rejection Ratio Spurious Emission Hum and Noise Audio Output Power (at 13.6 V DC) 0.
Chapter 4. How to Operation 4.1. Unit Description 4.1.1. Front Panel ① LCD Front Display Screen. Transmit distress call (Alert) MESSAGE. ② (※ You MUST NOT make a test of the transmission !! ) Push and hold down for 3 seconds, then the distress call will be activated. ③ Light will turn on in both receiving and transmitting DSC distress call ④ Light will turn on in both receiving other DSC call message other than distress call.
Short time press is for DSC Calling and long time press is for ⑧ MENU function. ⑨ This is ‘ESCAPE’ function in MENU mode. ⑩ It means this is being used as FUNCTION button. ⑪ PWR/VOL (Power Knob) ⑫ SQUELCH Knob Power ON/OFF and Volume Control. Squelch Control ⑬ Button description Input “1” when selects CH and inputs digit. 1 DUAL ] QZ When used this button, it works ON/OFF for dual watch function.
4 SCN When selects CH and inputs digit, input “4”. GHI When used this button, it does scanning all channels with converting “ALL” in screen (“CLR” when it finished) When inputs character, convert from 4 → G → H → I in order and ENT 5 TSCN When selects CH and inputs digit, input “5”.
0 TEST When selects CH and inputs digit, input “0”. *-/ When used this button, it can execute self-test menu. When inputs character, convert from 0 → * → _ → / in order and then ENT. When used this button, TAG is moving on the selected CH. TGO WX/CE On the main screen, it can select weather CH, move a cursor to forward for character input. H/L ENT It is a function to switch-over Tx power between 25W and 1W each other. In DSC MENU, it can be used for Item selection and Input confirmation. 4.1.2.
③ Key Pad : : To convert to the current CH and CH16. : It is used as Enter button for setting-up input data in MENU mode, while at normal times it is used for switching-over Tx power between 25W and 1W. , : To convert CH. (If pressed short it is to be one time, if pressed long time it is to be continuous). ④ Hook Switch If a Handmic is connected with Handmic Box a current CH ignored and go to common CH(CH16) automatically.
4.2. LCD Screen Description Item DISTRESS BUSY 25W(01W) ALL DUL 35.05.1250N 129.04.2741E 12:15PM WXALT ITU(USA,CAN, WEA) SIM(DUP) TAG RX(TX) 16 Function Description CH Name It represents detecting the sensitivity signal in existing CH.. It represents Tx Power. It represents the kinds of SCAN. It plays multi-scan between the existing CH and CH16. (It will be converted when scanning.) It indicates own ship’s latitude.
4.3. VHF Operation 4.3.1. Channel Selection 4.3.1.1. Channel 16 CH.16 is for distress and safety, and it should be monitored through dual-watch and tri-watch. Whenever selected current CH. key, it shifted from the current CH → CH 16 → CH 9 → 4.3.1.2. Channel Mode Selection (ITU,USA,CAN) How to select ITU CH : Press button and go to How to select USA CH : Press button and go to How to select CANADA CH : Press 17 button and go to button. button. button.
4.3.2. Weather Channel It can receive 10 numbers of weather channel provided by NOAA (National Oceanographic and Atmospheric Administration). STR-6000A can detect the alert sound of selected weather channel from the regular channel or the one during the channel scanning When selected it converts between weather channel and general channel. 4.3.3 Transmit and Receive ① Power and Volume switch It is operated by POWER ON switch and used for adjusting Sound volume.
(STR-6000A Main Body) (STR-6000A Microphone) 19
4.4. Menu Setup and Construction 4.4.1. Menu Construction 1. FRIENDS MMSI LIST 2. GROUP MMSI LIST 3. TELEPHONE LIST 4. LCD BACKLIGHT 5. LCD CONTRAST 6. GPS FUNCTION SET GPS TIME OFFSET TIME DISPLAY FORMAT TIME DISPLAY ON/OFF LL DISPLAY ON/OFF GPS ALERT ON/OFF 7. MANUAL GPS/TIME 8. DSC SET USER MMSI INDIVIDUAL REPLAY LAT/LONG REPLY DSC FUNCTION DISABLE MEDI/SHIP AIRCRAFT Menu Select Press MENU button long time -- MENU ITEM SELECT-- 9.
Menu Select 1. DISTRESS CALL 2. ALL SHIP CALL 3. INDIVIDUAL CALL 4. AUTO/SEMI CALL 5. TEST CALL 6. GROUP CALL 7. POSITION POLL 8. DISTRESS RELAY 9. DISTRESS RLY ACK 10. DISTRESS ACK 11. OTHERS ACK 12. DIRECT RELAY 13. RCV DISTRESS READ 14.
4.4.2. Menu Screen Construction and Initialization Press 1. FRIENDS MMSI LIST 2. GROUP MMSI LIST 3. TELEPHONE LIST 4. LCD BACKLIGHT 5. LCD CONTRAST button over one (1) second to get into the various Menu. ADD NEW FRIEND ADD NEW GROUP ADD NEW TELEPHONE LOW ~ HIGH(4 Steps/2) LOW ~ HIGH (16 Steps/10) TIME OFFSET Friend ID register Group ID register Call ID register BACKLIGHT Control CONTRAST Control - 00:00 TIME DISPLAY FORMAT – 12H/24H 6. GPS FUNCTION SET 7.
4.4.3. Menu Setup Press button at greater length. Overall construction of MENU Screen is as follows. Item Selection : From above screen, shift the cursor by using button and press button to select the current item. 4.4.3.1. FRIENDS MMSI LIST It can add/edit/delete the preferred friend’s name and associated MMSI up to 20 numbers. (It can save maximum 20 numbers) ¾ To add name to FRIENDS LIST ¾ To edit FRIENDS ¾ To delete FRIENDS 4.4.3.2.
4.4.3.3. TELEPHONE LIST It can add/edit/delete the preferred Telephone name and associated MMSI up to 10 numbers. (It can save maximum 10 numbers) ¾ To add name to TELEPHONE ¾ To edit TELEPHONE ¾ To delete TELEPHONE 4.4.3.4. LCD BACKLIGHT Set-up backlight level to adjust the brightness of LCD and Key Pad. 4.4.3.5. LCD CONTRAST It is used for setting-up suitable contrast of LCD. 4.4.3.6.
4.4.3.7. MANUAL GPS/TIME LAT/LONG MANUAL SET(Input position manually) : Ship’s position and longitude is displayed on screen together with time. To display “MANUAL SETUP”, value of latitude, longitude and time will be displayed in reverse status. This display mode will be cancelled as soon as GPS receiver is connected and come to display normal mode. Warning : This function is only available when GPS receiver is disconnected.
DSC FUNCTION DISABLE ¾ Set Up DSC function use. MEDI/SHIP_AIRCRAFT ¾ ON/OFF MEDIcal Transponder & SHIP and AIRCRAFT use. 4.4.3.9. RADIO SET CHANNEL NAME (CH NAME) ¾ Channel name modification and deletion. CHANNEL ON/OFF(CH ON/OFF) ¾ It is used for either permitting or stopping the use of current CH. WEATHER ALERT(Weather Alarm Setup) ¾ NOAA provides with a variety weather information regarding USA or CAN channel.
3 seconds in order to check button condition. ¾ PLL TEST (Test PLL condition on Tx and Rx) : It will be tested from minimum frequency to the maximum by 25KHz step. ¾ DISPLAY DEVIATION : LCD test (Display the character). ¾ SOUND TEST : Test on Bell, Emergency, Error and Alarm. ¾ SUB CPU Version : SUB CPU version check. 4.4.3.13. PRINT SETUP(Print Setup) This menu is ready to set-up Printer. ¾ Set-up auto printer ON/OFF function when receiving DSC. ¾ SELF TEST ON/OFF 4.5.
seconds until the reception is confirmed. In case that it is interfaced with any navigational equipment, the data on time and position will be automatically input. It is available to manually input the time when the position data and position are decided. If the transmission is made when it is not connected with any navigational equipment or under the conditions where any single manual input has not been made, it will transmit zero information.
4.5.1. Configuration of CALL Screen Press button in short. The whole display configuration of DSC CALL MENU is as follows; Item selection : Use the wanted item and press buttons in the above Screen and move to button. 4.5.2. CALL Menu Description and Instruction 1. DISTRESS CALL 2. ALL SHIP CALL 3. INDIVIDUAL CALL 4. AUTO/SEMI CALL 5. TEST CALL 6. GROUP CALL 7. POSITION POLL 8. DISTRES RELAY 9. DISTRES RLY ACK 10. DISTRES ACK 11. OTHERS ACK 12. DIRECT RELAY 13. RCV DISTRESS READ 14.
4.5.2.1. DISTRESS CALL(Distress message SETUP and Call) On screen of CALL ITEM SELECT, select 1.DISTRESS CALL by using buttons and then press button. In order to select types of distress (Nature of Distress), select > NATURE : UNDEFINE list and then press button. It shows relative menu of types of distress such as following box on a small screen. Select a wanted distress list by using buttons in this screen.
In order to input distress position (POSITION), select using buttons and then press >LAT / > LONG list by button. It makes cursor blink and then input wanted longitude/latitude on the blinking cursor. After select TIME-UTC buttons and then press button. It makes cursor blink. After input UTC time on the blinking list and press button. Press button for 3 seconds to send out distress message.
4.5.2.2. ALL SHIPS MESSAGE SETUP AND CALL Select 2.ALL SHIP CALL list on CALL ITEM SELECT screen by using buttons and then press button. ‘CATEGORY' list is a function for selecting SAFETY or URGENCY, either and press button after move the cursor to > CATEGORY list by using buttons. Then, select one of SAFETY or URGENCY on the following small screen and the small screen is disappeared when press button after selecting a wanted list by using buttons.
After going through the edition of MESSAGE, select > TRANSMIT DSC list and transmit by suing buttons. 4.5.2.3. INDIVIDUAL MESSAGE SETUP AND CALL Press button after select 3. INDIVIDUAL CALL list on CALL ITEM SELECT screen by using Press buttons. It makes following screens. button after select > ADDRESS list by using buttons. It shows following screens and then press Then, input ADDRESS(MMSI) on the list cursor is blinking. 33 button, again.
By using button, select and press > CATEGORY button then following small screen shown up. Here on the item where the cursor is flickering, by using By using button and press button, select > TELECMD1 and press button then following small screen comes up and again press By using button. button, select button. > TRANSMIT DSC and press button then following small screen comes up from which you may choose YES if you want or NO by using button to send out message one time.
4.5.2.4. AUTO/SEMI-AUTO Message Edit and Call This function as an option will be further realized soon. 4.5.2.5. TEST CALL This function is used for testing call, following procedure in editing and calling for position messages shall be done. On CALL ITEM SELECT screen, by using button. 5. TEST CALL item and press By using button, select button, select > ADDRESS and press then following small screen comes up. Again press button, button.
4.5.2.6. GROUP MESSSAGE EDIT AND CALL On CALL ITEM SELECT screen, select the item 6. GROUP CALL by using button, and press button. This item 'GROUP ID' ready to input the opponent’s ID. From this item, press button then following small screen comes up, press button then cursor is flickering to be ready for inputting the wanted information. In this 'WORK CH', input the wanted CH for transceiving according to the applicable standard.
After finishing message edit, select > TRANSMIT DSC item by using button and send out the message. 4.5.2.7. POSITION MESSAGE EDIT AND CALL On CALL ITEM SELECT screen, select item 7. POSITION CALL by using button and press button. Select > ADDRESS using button and press following small screen comes up, then again press ADDRESS(MMSI) on the item where the cursor is flickering. 37 button then button.
After finishing the message edit, select the item > TRANSMIT DSC by using button and send-out message. 4.5.2.8. DISTRESS CALL RELAY Select item8. DISTRESS RELAY on CALL ITEM SELECT screen by using button and press button. After select > FORMAT using button and press button then following small screen comes up. From this screen, select the appropriate item (ALL SHIP or INDIVIDUAL) using press button.
Select > ADDRESS(MMSI) using button and press button then following screen comes up. From this screen, select the appropriate item by using button and press Select > TRANSMIT DSC by using button. button and press button then following screen comes up. From this screen, select YES or NO for sending Message by using button and press After finishing Message edit, press button.
4.5.2.9. DISTRESS RELAY ACKNOWLEDGEMENT On “CALL ITEM SELECT” screen, select 9. DISTRESS RLY ACK by using button and press button. It is impossible to edit Message but only possible to response at >TRANSMIT DSC after editing using button. Acknowledgement to DISTRESS in Individual Call is only one time available within 5 minutes. 4.5.2.10. RESPONSE to DISTRES CALL On “CALL ITEM SELECT” Screen, select 10. DISTRESS ACK by using button.
4.5.2.11. RESPONSE to THE OTHER CALL On “CALL ITEM SELECT” screen, Select 11. OTHERS ACK using button and press Select > CATEGORY button. from the screen by using button and press button to come up small screen where to select the item and press button. Select > TELECMD1 from screen using button and press button then small screen comes up where to select the item and press button.
Select > WORK/LAT/LONG/TIME-UTC from screen respectively by using button and input the information. After finishing all information, select > TRANSMIT DSC at the following screen by using button and press YES or NO for sending Message and press button to decide button. 4.5.2.12. DIRECT RELAY On “CALL ITEM SELECT” screen, Select 12. DIRECT RELAY using button and press button. Select > FORMAT from screen using button and press button.
Select > ADDRESS from screen using button and press button. Afterwards select the methods of input for ADDRESS (MMSI) small screen and press from button. Select > DIST-ID from screen by using button and press button. Afterwards select the methods of input for ADDRESS (MMSI) from small screen and press button. If it is unknown ADDRESS(MMSI) of the distressed ship, input ????????. Select > NATURE from the screen using button and press button.
Select > LAT/LONG/DIST-UTC button and press respectively from screen using button and input appropriate information. After finishing edit, select and press >TRANSMIT DSC using button button to decide YES or NO to send message and press button.
4.5.2.13. RECVEIVING DISTRESS READ On “CALL ITEM SELECT” screen, select 13. RCV DISTRESS READ using button and press button. Then following message related to receiving distress is seen.. Display RCV DISTRESS READ screen as follows ; RCV : 08 : means for 8 received messages. 1 DUAL QZ ] PRE : 1 : Display a message from 7 to 1 if press button. 3 DIM NEXT : 3 : Display a message from 1 to 8 of press DEF button. 4.5.2.14. OTHER RECEIVING MESSAGE READ On “CALL ITEM SELECT” screen, Select 14.
4.5.2.15. DSC Message Receiving Display a message which is just received with alarm. Stop a alarm if press Press CLR button and go back to main screen. button over twice if received succession message are over two. Select > RCV DISTRESS READ or > RCV OTHERS READ for received message search. Able to print out automatically printer connected with if a message received in case of auto printer mode setup. 4.5.2.16.
¾ END OF SEQUENCE contents among the received message should be ACK RQ.
Chapter 5. Installation 5.1. Unpacking Package and Inspection When dismantling the package, please treat with great care in checking the contents with order specification. Please observe external surface whether it is damaged during transportation and if there find damaged parts, then install after proper treatment made. In case of handling difficulty, please contact SAMYUNG ENC for proper treatment.
5.4. Cabling Rear part of the unit has connectors, which can be efficiently interfaced with power, antenna and other cables.
5.4.1. Power Connection 4 P connector located in the rear of the unit is used to supply power, of which Number 1 pin is ”+” and Number 2 pin is “-“ those can connect to Power supply [DC13.6V] 5.4.2. Connects to External Speaker 1P connector located in rear of the unit is a Speaker Connection Connector. 5.4.3. How to setup Antenna FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
can be endurable for specific electric current. 2. Please tighten connectors of Tx/Rx antenna and speaker to stand for ship’s rolling and pitching.
Chapter 6. Channel List 6.1. ITU Channel SHIP SHIP TO TO SHIP SHORE CH Tx (MHz) Rx (MHz) 01 02 03 04 156.050 156.100 156.150 156.200 160.650 160.700 160.750 160.800 Public Correspondence, Duplex Public Correspondence, Duplex Public Correspondence, Duplex Port Operations, Duplex NO NO NO NO YES YES YES YES 05 156.250 160.850 Port Operations, Selected VTS Area NO YES 06 07 08 09 10 11 156.300 156.350 156.400 156.450 156.500 156.550 156.300 160.950 156.400 156.450 156.500 156.
CH Tx (MHz) Rx (MHz) 60 61 62 63 64 65 66 67 68 69 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 160.625 160.675 160.725 160.775 160.825 160.875 160.925 156.375 156.425 156.475 70(2) 71 72 73 74 77 78 79 80 81 82 83 84 85 86 87 88 156.525 156.575 156.625 156.675 156.725 156.875 156.925 156.975 157.025 157.075 157.125 157.175 157.225 157.275 157.325 157.375 157.425 156.575 156.625 156.675 156.725 156.875 161.525 161.575 161.625 161.675 161.725 161.775 161.825 161.
6.2. USA Channel CH Tx (MHz) Rx (MHz) TRAFFIC TYPE SHIP SHIP TO TO SHIP SHORE NAME TAG PORT OPS/VTS UNAUTHORIZ ED PORT OPS/VTS SAFETY COMMERCIAL COMMERCIAL CALLING COMMERCIAL VTS PORT OPS/VTS 01A 156.050 156.050 Port Operations, Selected VTS Areas YES YES 03A 156.150 156.150 US Government, Coast Guard YES YES 05A 156.250 156.
CH Tx (MHz) Rx (MHz) TRAFFIC TYPE 61A 156.075 156.075 U.S. Government, Canadian Coast Guard 63A 156.175 156.175 Port Operations, VTS in Selected Areas U.S. Government, Canadian Commercial 64A 156.225 156.225 Fishing 65A 156.275 156.275 Port Operations 66A 156.325 156.325 Port Operations 67(2) 156.375 156.375 Commercial, bridge-to-bridge 68 156.425 156.425 Boat Operations, Recreational 69 156.475 156.475 Boat Operations, Recreational 70(3) 156.525 Digital Selective Calling - DSC 71 156.575 156.
6.3. CANADA Channel CH Tx (MHz) 01 02 03 04A 05A 06 07A 08 09 10 11 12 156.050 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 13(1) 156.650 14 156.700 15(1) 156.750 16 156.800 17(1) 156.850 18A 156.900 19A 156.950 20(1) 157.000 21 157.050 21A 157.050 21B 22A 23 24 25 25B 26 27 28 28B RX Only 157.100 157.150 157.200 157.250 RX Only 157.300 157.350 157.400 RX Only Rx (MHz) TRAFFIC TYPE 160.650 Public Correspondence, Duplex 160.
CH Tx (MHz) Rx (MHz) 60 156.025 160.625 61A 156.075 156.075 62A 156.125 156.125 64 156.225 160.825 64A 156.225 156.225 65A 156.275 66A 156.325 67 156.375 68 156.425 69 156.475 70(2) 71 156.575 72 156.625 73 156.675 74 156.725 77 156.875 78A 156.925 79A 156.975 80A 157.025 81A 157.075 156.275 156.325 156.375 156.425 156.475 156.525 156.575 156.625 156.675 156.725 156.875 156.925 156.975 157.025 157.075 82A 157.125 157.125 83 157.175 161.775 83A 157.175 157.175 83B RX Only 161.775 84 157.225 161.
6.4. Weather Channel WEATHER CH Rx(MHz) Type Channel Type WX1 WX2 WX3 WX4 WX5 WX6 WX7 WX8 WX9 WX10 162.550 162.400 162.475 162.425 162.450 162.500 162.525 161.650 161.775 163.
Chapter 7. Position Information Interface This unit is effectively designed for convenient use, after receiving NMEA0183 FORMAT Typed GPS information that will interface internally and input automatically with current own vessel’s latitude and longitude value when distress call is occurred. It is available to input the time when determined with position information and position by manual.
Chapter 8. Packing List 8.1. Oversea VHF STR-6000A Standard NO Item Feature Dimension Q’ty Check STR-6000A 1 CODE NO. 2 CODE NO. 5 L=3m 6 Mic Holder 7 GPS Plug CODE NO. CODE NO. CODE NO. 9 10 Fuse 11 Manual STR-6103 STR-595 10A(20mm) CODE NO. STR-598 STR-6000A-ME CODE NO. 61 1 A-01 1 A-07 1 A-03 Hook INCL. Cable 20 STR-594 KIV 5.5mm2 CODE NO. Attached to Main unit 2 STR-6003 Ø4 X 16 Steel Piece Ground Cable STR-6102 RCA Plug L=2m 8 CODE NO.
VHF STR-6000A Option NO Item 1 Antenna 2 VHF Antenna Cable 3 Antenna Bracket 4 U-Bolt Feature Dimension SAN-150 CODE NO. STR-585 RG-8U L=15m CODE NO. 5 Power Supply 6 Power Supply 7 AC Power Cable 8 9 DC Power Cable DC Power Cable/ B.K Cable 10 Power Fuse 11 Power Fuse 12 Flush Mount (Bracket) CODE NO. Ground Cable STR-581 SP-6000AD CODE NO. STR-582 CVV-SB 2C 2SQ L=3m CODE NO. STR-588 CVV-SB 2C 2SQ L=3m CODE NO. STR-589 CVV-SB 4C 1.25SQ L=3m CODE NO.
8.2. Domestic VHF STR-6000A Standard(1 of 2) NO 1 Item Feature Dimension STR-6000A Main Unit CODE NO. Q’ty Check Remark SM-6000 INCL. MIC 1 STR-6100 SS-6000 2 Speaker 1 CODE NO. 3 ACC-6000D-001 Bracket CODE NO. 4 CODE NO. 5 Mic Holder 6 GPS Plug CODE NO. 7 Steel Piece 8 Ground Cable 9 Fuse 10 Antenna 11 VHF Antenna Cable 12 Antenna Bracket CODE NO. STR-6103 KIV 5.5mm2 STR-595 10A(20mm) CODE NO. 1 A-07 1 A-03 Hook INCL. Cable STR-6003 Ø4 X 16 CODE NO.
VHF STR-6000A Standard(2 of 2) NO Item Feature Dimension Q’ty Check Remark 1 B-01 SCN-20-2P 1 B-02 SCN-20-3P 1 B-03 SCN-16-4P SCN-20-4P Ø63 X 80mm 13 U-Bolt 4 CODE NO. 14 Power Supply 15 AC Power Cable 16 17 DC Power Cable DC Power Cable 18 Power Fuse 19 Power Fuse 20 Ground Cable 21 Manual STR-601 SP-580AD CODE NO. STR-581 CVV-SB 2C 2SQ L=3m CODE NO. STR-588 CVV-SB 2C 2SQ L=3m CODE NO. STR-589 CVV-SB 4C 1.25SQ L=3m CODE NO. STR-590 3A(20mm) CODE NO.
Chapter 9.
Chapter 10.
