Datasheet

87
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
MINIATURE TYPES
·Standard series for general purposes
·High voltage, high capacitance series
·Voltage range of 6.3~500V
·Complied to the RoHS directive
● DRAWING
Standard, For General Purposes
Series
SD
Unit : mm
Item Characteristics
Operating temperature range
Leakage current max.
Capacitance tolerance
Dissipation factor max.
(at 120Hz, 20°C)
Low temperature characteristics
(Impedance ratio at 120Hz)
Load life
(after application of the rated
voltage for 2000 hours at 85°C)
Shelf life (at 85°C)
±20% at 120Hz, 20°C
Capacitance > 1000μF : tanδincreases by 0.02 for each 1000μF from below value.
WV≦100
I = 0.01CV or 3μA whichever is greater (after 2 min)
I = 0.03CV or 4μA whichever is greater (after 1 min)
WV >100
I = 0.02CV+15μA (after 5 min)
WV
Temperature range
6.3 ~ 450
-40 ~ +85°C
500
-25 ~ +85°C
WV
tanδ
6.3
0.28
10
0.24
16
0.20
25
0.16
35
0.14
50
0.12
63
0.10
100
0.08
160 ~ 250
0.15
350 ~ 500
0.20
WV
Z-25°C/Z+20°C
Z-40°C/Z+20°C
6.3
5
12
10
4
10
16
3
8
25
2
5
35
2
4
50~100
2
3
200~350
6
8
160
4
6
400~450
10
12
500
12
─
ØD 5 6.3 8 10 12.5 16 18 22 25.4
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0 12.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8 1.0 1.0
α 0.5 1.0
β 1.5 2.0 3.0
Leakage current
Capacitance change
tanδ
Less than specified value
Within ±20% of initial value
Less than 200% of specified value
Solvent Proof
WV≦100V
ØD+αmax.
L+βmax.
15 min. 4 min.
＋
－
P±0.5
Insulating sleeve Ød±0.05 Tinned copper-ply wire
Safety vent(Ø6.3 up)
60Hz
0.75
0.80
0.85
0.80
0.90
120Hz
1.00
1.00
1.00
1.00
1.00
1kHz
1.55
1.35
1.15
1.40
1.13
10kHz
2.00
1.50
1.15
1.60
1.15
50kHz
2.00
1.62
1.32
1.70
1.32
100kHz≦
2.00
1.75
1.50
1.80
1.50
● FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT
~ 47
68 ~ 680
1000 ~
~ 220
330 ~
6.3~100
160~500
Frequency
μF
WV
After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.
The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.
2013-4장-01-수정 2012.11.22 11:38 PM 페이지87 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T