IPX3702HD-5314 Installation Guide
INFORMATION TO USER CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). CONTACT QUALIFIED SERVICE PERSONNEL FOR INTERNAL PARTS. This symbol is intended to alert the user the presence of un-insulated “dangerous voltage” within the product’s enclosure, which may be sufficient magnitude to constitute a electric shock risk to persons.
IPX/IPN Series Installation Guide Table of Contents 1. FEATURES ............................................................................................................. 4 2. PACKAGE CONTENTS............................................................................................. 5 3. PART NAMES ........................................................................................................ 6 4. INSTALLATION ..................................................................................
IPX/IPN Series Installation Guide 1. FEATURES Camera • • • • • Full HD outdoor fixed dome IP camera (Vandal proof) High quality compression in real time streaming 1/2.7” High Quality CMOS Image Sensor True Day / Night (ICR) Remote Zoom/Focus Control(One Click AF) Streaming • • • • Dual streaming mode De-interlacing on DSP Burnt-in text supported Unicast/Multicast supported Video/Audio • • • • • Video compression: H.264/MJPEG, 25/30FPS@1080p(PAL/NTSC) Audio compression: G.
IPX/IPN Series Installation Guide 2. PACKAGE CONTENTS Unpack carefully and handle the equipment with care. The packaging contains: Camera DC power adaptor DC jack cable 8-pin and 2-pin terminal block S-Video jack to 3.5mm plug Screws and anchors Side plug Hex wrench driver Side cover RJ45 coupler Quick installation guide Installation template i The package contents are subject to change without prior notice. Note 01A.
IPX/IPN Series Installation Guide 3. PART NAMES Top View ⑦ ⑧ ⑥ ⑤ ① ② ④ ③ * Models and their appearance are subject to change without any prior notice. ① Rest button The reset button can be used for restarting the device or resetting it to Factory Default. ② Focus buttons Use the buttons to manually/automatically determine correct focus. ③ Zoom In/Out buttons Use the buttons for camera to cover the wide field of view or to concentrate narrow field of view.
IPX/IPN Series Installation Guide 4. INSTALLATION 1) Place the installation template (paper) that is included in the package on the desired installation surface. 2) Drill three holes in correct positions based on the template paper, and insert anchor blocks into the holes. 3) When placing the camera body to the installation surface, match three alignment holes with three anchor blocks. 4) Tighten the surface anchor studs. 5) Connect all the required cables to the camera. 6) Adjust the lens position.
IPX/IPN Series Installation Guide 4.1. Installation Template ! Caution 01A.01 Installation template image’s size scale in this installation guide is not 1:1. The correct-size template design paper can be found inside the package separ ately.
IPX/IPN Series Installation Guide 4.2. Setting the Lens Position 1) Remove the dome cover to control the positioning buttons, or use web site setup (Setup > Video & Audio >Repositioning) to adjust the camera. 2) Refer to 3. Part Names for the button locations; to pan, use ‘+’ and ‘–‘pan buttons. To tilt, use ‘+’ and ‘-‘tilt buttons. PAN & TILT buttons A. Tilt the lens with tilt ‘+’ and ‘-‘ buttons B.
IPX/IPN Series Installation Guide 5. CONNECTIONS VIDEO DO Out DI AUDIO C 1 C 1 Out In ETHERNET ① Audio input/output The camera has a mono audio input and a mono audio output. Due to low audio output power, an amplified speaker is recommended for enhanced sound (Do not connect a headphone or earphone directly to the camera). AUDIO Out In Amp Speaker Mic ② Sensor (DI) connection The camera provides 1 channel D/I.
IPX/IPN Series Internal Installation Guide +3.3V Internal DI Output of Sensor + DI - COM COM Relay Type Output of Sensor + - - + Voltage Type ③ Alarm (DO) connection Only the relay type is supported. Relay Rating: Max 24VDC 50mA ! Do not exceed the maximum relay rating. Caution Internal Device DO Relay Type COM ! Must connect GND port which is located end of the DO terminal block side. Caution ④ LAN connector This is a 10/100 Base-T Ethernet cable.
IPX/IPN Series Installation Guide 6. CONFIGURATION 6.1.Set up network environment The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the device from converting the MAC address’s hexadecimal numbers, which is attached to the device. Be sure that the device and PC are on a same area network before running the installation. IP address : 192.168.xxx.xxx Subnet mask: 255.255.0.0 6.1.1.
IPX/IPN Series Installation Guide 6.1.2. Custom IP Environment IPAdminTool is provided with SDK at the following SDK path. {SDK root}\BIN\TOOLS\AdminTool\ IPAdminTool is a management tool, which automatically scans all of the network products for users to perform administrative tasks, which includes network configurations, firmware update, device reboot, and device organizations. To modify the device’s default IP address for customized network area; 1.
IPX/IPN Series Installation Guide 6.2. View video on web page Type the proper IP address to view the live streaming images through a web browser. The default username and password is root / pass. 1. The browser asks to install the ActiveX. Click Allow. 2. Setup.exe installation link or pop-up window appears, depends on Microsoft® Internet Explorer version. Proceed with rest of setup installation. 01A.
IPX/IPN Series 3. Installation Guide Follow the instructions of the dialog boxes and complete the installation. Once the installation is complete, start the web browser again and check if video stream is displayed in the main view frame. ! Caution If “This software requires the Microsoft XML Parser V6 or higher. Please download MSXML6 from the Microsoft website to continue. Error code: Cannot create XMLDOMDocument.” message appears, download and install the Microsoft Core XML Services (MSXML) 6.0. 6.
IPX/IPN Series Installation Guide 6.3. Reset Refer to 3. Part Names for the reset button location. Perform the following procedures to reset your device: 1. 2. Push the Reset button and hold for 1~2 seconds. The red led lights up. Wait for the system to reboot. 6.4. Factory Default Refer to 3. Part Names for the reset button location. Resetting the device back to the factory default will initialize all parameters including the IP address back to the factory defaults.
IPX/IPN Series Installation Guide APPENDIX (A): SPECIFICATIONS Summary Camera Module CMOS ELECTRICAL Lens Image Sensor Effective Pixels Scanning system Resolution Min. Illumination AGC Control Focal Length Aperture Length Zoom Ratio 1/2.7” 1080p CMOS 1920x1080 Progressive scanning 1920 x 1080 Color: 0.5 lux, F1.2 BW: 0.001 Lux (B/W, Sens-up 32X) Auto 3.0 ~ 9.0mm Fw1.2 ~ Ft/2.1 3X Day & Night Removal IR Cut Filter Compression Format H.
IPX/IPN Series Installation Guide Electrical Characteristics Power Source Power Consumption DC 12V, AC24V / PoE IEEE802.3af (Class 0) DC12V and AC24V : 1.5A PoE : 800mA 1 Vp-p, 75Ω, Composite MICin, 0.178Vp-p, 10K Ω Lineout, 2.26Vp-p, 10K Ω Max 50mA@5VDC, TTL level 1.
IPX/IPN Series Installation Guide APPENDIX (B): POWER OVER ETHERNET The Power over Ethernet (PoE) is designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard. IEEE 802.3af allows for two power options for Category 5 cables. The IEEE 802.3af-2003 standard allows up to 15.4 W power to device. However, 12.95W is the maximum available power, as some power gets lost in the cable.
IPX/IPN Series Installation Guide APPENDIX (C): DIMENSIONS (Unit: mm) 01A.
IPX/IPN Series Installation Guide APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE Refer to the following table when you convert the MAC address of your device to IP address.
IPX/IPN Series Installation Guide REVISION HISTORY MAN# DATE(M/D/Y) 01A.00 09/25/2012 First release version 01A.01 10/05/2012 Operation Temp. confirmed 01A.
