SyncMaster T200HD/T220HD LCD Monitor User Manual
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Safety Instructions Do not place candles, mosquito repellant, cigarettes and any heating appliances near the product. • Otherwise, this may result in fire. Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. Put down the monitor carefully.
Safety Instructions Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray cleaner directly onto the surface of the product. • Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off. Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10.
Safety Instructions If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. • Otherwise, this may result in electric shock or fire. Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. • Otherwise, this may result in electric shock or fire. When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.
Safety Instructions When using a fixed screen for a long time, an afterimage or stain may occur. • If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver. Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing.
Safety Instructions Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach. • If children have had the battery in their mouths, consult your doctor immediately. When replacing the battery, insert it with right polarity (+, -). • Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Safety Instructions Be careful when adjusting the angle of the product or the height of the stand. • This may result in personal injury as your hand or fingers may become caught. • Also, if you tilt the product too far, it may fall and cause personal injury. Do not install the product in a location low enough for children to reach. • Otherwise, it may fall and result in personal injury. • Since the front part of the product is heavy, install the product on a level and stable surface.
Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Introduction Sold separately USB Cable TV Antenna Cable Component(PR, PB, Y) Cable (Coaxial Cable) Audio cable Digital audio optic output cable Remote Control Batteries (AAA X 2) BN59-00624A (Not available in all locations) Cable holding ring Stand Body Others Cleaning Cloth Stand Base Note Cleaning Cloth is only provided for highly polished black products as a product feature.
Introduction Your Monitor Front Activates a highlighted menu item. Push the ' ', button to change the input signal source. Changing the source is only allowed for external devices connected to the product at the time. To switch Screen modes: [PC] →[Ext.] → [DVI] → [TV] → [Component] → [HDMI1] → [HDMI2] >> Click here to see an animation clip MENU Use this button to open the on-screen menu and to exit from the on-screen menu or to close the screen adjustment menu.
Introduction Note The button to the right of the monitor are touch-sensitive buttons. Touch a button lightly with your finger. Power indicator This light is lit when operating normally, and blinks once when your adjustments are saved. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.
Introduction PC Connect the PC terminal at the back of your monitor to your computer. HDMI/PC/DVI-D AUDIO IN / DIGITAL AUDIO OUT (OPTICAL) / EX-LINK HDMI/PC/DVI-D AUDIO IN Connect the [ HDMI/PC/DVI-D AUDIO IN ] terminal at the back of your product to your computer’s sound card.
Introduction The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on its model. Using the Anti-Theft Kensington Lock 1.
Introduction Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the product. Make sure to use a TV antenna cable (sold separately) as the antenna cable. COMMON INTERFACE This contains information on CAM inserted in the CI slot and displays it. The Application Info inserting is about the CI CARD. You can install the CAM anytime whether the TV is ON or OFF.
Introduction Remote Control POWER Number Button -/-TV/DTV CH LIST MUTE MENU Up-Down Left-Right buttons ENTER RETURN SOURCE PRE-CH GUIDE D.MENU P EXIT INFO TTX/MIX COLOR BUTTON P.MODE, M/B (MagicBright) S.MODE AUTO P.SIZE DUAL SUBTITLE SOURCE PIP 1. POWER Turns the product On/Off. 2. Number button Press to change the channel. 3. -/-- (One/Two-Digit channel selection) Use to select a channel numbered ten or over. Press this button, and the "--" symbol is displayed.
Introduction Enter the two-digit channel number. 4. TV/DTV Selects the TV and DTV mode directly. 5. CH LIST It display "Channel List" on the screen. 6. Adjusts the audio volume. 7. MUTE Adjusts the audio volume. 8. MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. 9. Up-Down LeftRight buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 10. ENTER Activates a highlighted menu item. 11.
Introduction The monitor has three automatic picture settings that are preset at the factory. Then press the button again to circle through available preconfigured modes. (Dynamic > Standard > Movie) PC / DVI Mode : M/B ( MagicBright ) MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes. (Entertain > Internet > Text > Dynamic Contrast > Custom) 22. S.
Connections Connecting Cables Connecting to a Computer Connect the power cord for your monitor to the POWER port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the [PC] port on the back of your monitor. [PC] Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the [DVI-D] Port on the back of your Monitor.
Connections • If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press 'SOURCE [ ]' button to have the monitor double-check the input signal source. Connecting to a Macintosh 1. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the D-SUB port on the back of your monitor. [PC] Note Turn on the monitor and Macintosh.
Connections Note Connect to the DVD Devices input if the device has a EXT (RGB) jack. You can watch DVD simply by hooking up the DVD player with the monitor as long as the power is on. 1. Connect the EXT (RGB) port of the monitor to the DVD Player using a SCART jack. 2. When a Scart device is connected to your monitor, the Source automatically changes to Ext.
Connections Connecting DVD / DTV Set Top Box Note Connect to the DVD / DTV Set Top Box input if the device has a [COMPONENT IN] connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the monitor. Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the [PR, PB,Y] input ports using a component video cable (PR, PB,Y).
Connections a. Input devices such as digital DVD are connected to the HDMI IN terminal of the monitor using the HDMI cable. When all the connections are completed, connect the power cords for the monitor and DVD(or the device connected to the digital output terminal). Select HDMI using the ‘SOURCE [ 2. ]‘ button. Connecting Using a DVI to HDMI Cable Connect the DVI output terminal of a digital output device to the [HDMI IN] terminal of the monitor using a DVI to HDMI cable.
Connections 1. Connect the [DIGITAL AUDIO OUT (OPTICAL)] terminal of your monitor to the digital sound input terminal of your digital amplifier using an optical cable. 2. Set the Internal Mute On in the Sound menu using the MENU button. 3. Adjust the sound volume using the Volume button of your amplifier 4. If the connections are set up, power up your monitor and amplifier. Note • Because no sound is emitted from the monitor, you need to use an amplifier.
Connections Connecting Headphone Note You may connect your headphones to the monitor. 1. Connect your headphones to the Headphone connection terminal. Using the Stand Monitor Assembly Monitor and Bottom Tilt angle You can adjust the tilt angle within a range of 5° forward to 25° backward for the most comfortable viewing angle.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click 3. Click "Personalization" and then "Display Settings". 4. Click "Advanced Settings...". 5. Click "Properties" in the "Monitor" tab.
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will..." then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location..." then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver) then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11.
Using the Software Natural Color Natural Color Software Program One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
Adjusting the Monitor Picture Available Modes • PC / DVI • TV • DTV • Ext. • Component • HDMI Note The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Picture : PC / DVI MagicBright MagicBright is a feature providing optimum viewing environment depending on the contents of the image you are watching.
Adjusting the Monitor • Text For documentations or works involving heavy text. • Dynamic Contrast Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast. • Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu.
Adjusting the Monitor The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, auto function is performed. The direct button on the remote control is the 'AUTO' button. (Available in PC Mode Only) Screen Adjustment (Available in PC mode only) • Coarse / Fine : • Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.
Adjusting the Monitor Image parameters are replaced with the factory default values. Picture Options • Colour Tone The tone of the color can be changed.
Adjusting the Monitor Adjusts the individual R, G, B color controls. • Size You can switch the Size. Wide / 4:3 Reset Picture parameters are replaced with the factory default values.
Adjusting the Monitor Picture : TV / DTV / Ext. / Component / HDMI Mode The Monitor has three automatic picture settings ("Dynamic", "Standard", and "Movie") that are preset at the factory. You can activate either Dynamic, Standard, or Movie. The direct button on the remote control is 'P.MODE' button. • Dynamic Selects the picture for high-definition in a bright room. • Standard Selects the picture for the optimum display in a normal environment.
Adjusting the Monitor • Brightness : Adjust the Brightness. • Sharpness : Adjust the Sharpness. • Colour : Adjust the colour. • Tint : Adds a natural tone to the display. (It is activated when the signal is NTSC.) Colour Tone The tone of the color can be changed. Cool1 / Cool2 / Normal / Warm1 / Warm2 - ‘Warm1’ or ‘Warm2’ is only activated when the picture mode is ‘Movie’. - Settings can be adjusted and stored for each external device you have connected to an input of the TV.
Adjusting the Monitor Size You can switch the Size. The direct button on the remote control is 'P.SIZE' button. Auto Wide - Automatically adjusts the picture size to the "16:9" aspect ratio. Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals. 16:9 - Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting. Wide Zoom - Magnify the size of the picture more than 4:3. (Move the screen up/donw using the or button after selecting the button.
Adjusting the Monitor Only when setting the picture size to Auto Wide can the user determine the Screen mode. Each individual European country requires a different picture size so this function is intended to help users to select it. - ‘Screen mode’ is supported in TV, Ext., Component (480i/1080i) and HDMI (480i/1080i) - Picture Size is available in Auto Wide mode - This function is not available in PC or Component,Ext., HDMI mode. Wide / 16:9 / Wide Zoom/ Zoom / 4:3 Digital NR Digital Noise Reduction.
Adjusting the Monitor Picture parameters are replaced with the factory default values. • OK • Cancel Sound Available Modes • PC / DVI • TV • DTV • Ext. • Component • HDMI Note The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Mode The Monitor has a built-in high fidelity stereo amplifier. • Standard Choose Standard for the standard factory settings.
Adjusting the Monitor Choose Speech when watching a show that is mostly dialogue (i.e., news). • Custom Choose Custom if you want to adjust the settings according to personal preference. Equalizer You can adjust the left and right sound balance and the low or high volume as you want. SRS TS XT You can experience sonorous and vivid sound, as if from 5.1 channel speakers.
Adjusting the Monitor Auto Volume Reduces the differences in volume level among broadcasters. • Off • On TV Speaker If you set this menu "On", sound output from the speakers is muted in case of using the home theater. • Off • On Channel Available Modes • TV Note The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.
Adjusting the Monitor Country Select the country in which the product is being used before you use the Auto Store feature. If you do not see your country in the list, select Others. Auto Store You can scan the frequency ranges available on your television in your area and store all the channels found automatically. Manual Store You can scan the frequency ranges available on your television in your area and store all the channels found manually.
Adjusting the Monitor • Programme Inputting the appropriate program number on the screen. • Colour System Adjusts repeatedly until the colour is of the best quality. (Auto <-> PAL <-> SECAM <-> NTSC4.43 ) • Sound System Adjusts repeatedly until the sound is of the best quality. • Channel You can store television channels, including those received via cable networks. When storing channels manually, you can choose: Whether or not to store each of the channels found.
Adjusting the Monitor • Child Lock Protects children from viewing inappropriate programs by blocking certain broadcast or video programs. The Child Lock feature can be selected only from the remote. Sort It's used to exchange the numbers of two channels. Name Name the device connected to the input jacks to make your input source selection easier.
Adjusting the Monitor The following characters are available: Letters of the alphabet (A~Z) / Numbers (0~9) / Special characters (+, -, *, /, space) Fine Tune Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. Setup Available Modes • PC / DVI • TV • DTV • Ext. • Component • HDMI Note The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.
Adjusting the Monitor When the TV is initially powered on, several basic settings proceed automatically and sub sequently. the following settings are available. • Shop : Select Shop Mode. only when setting up in TV store. • Home : Select Home Mode. when installing this TV at home. (Available in Analog TV Mode Only) Language You can choose one of 21 languages. The language chosen affects only the language of the OSD. Time • Clock Set You can set the current time.
Adjusting the Monitor Use to set the Monitor to be turned off automatically in certain minutes. • • Off, 30, 60, 90, 120, 150, 180 Timer1 / Timer2 / Timer3 You can have the monitor turned on or off automatically at a specified time. • On time Select hour, minute and “On”/”Off”. (To activate timer with the setting satisfied, set to ‘On’) • Off time Select hour, minute and "On"/"Off".
Adjusting the Monitor Adjust a Programme Blue Screen If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the "Blue screen" mode to "Off". • Off • On Melody A melody sound can be set to come on when the monitor is powered On or Off. • Off : Turns off the melody function. • Low : Sets the melody volume to low. • Medium : Sets the melody volume to medium.
Adjusting the Monitor Light Effect You can turn on/off the LED on the front of monitor according to the situation. use it for saving power or when the LED dazzles your eyes. • Off : LED will not come on. • In Standby : Turns the LED on in standby mode. • In Watching TV : Turns the LED on while watching TV. • Always : LED is always on. Light Level Use to adjust the light level i.e., the brightness of the light.
Adjusting the Monitor Energy Saving This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the "Energy Saving" mode option to "High" to reduce eye fatigue as well as power consumption. • Off : Turns off the energy saving function. • Low : Sets the TV to low energy saving mode. • Medium : Sets the TV to medium energy saving mode. • High : Sets the TV to high energy saving mode.
Adjusting the Monitor Input Available Modes • PC / DVI • TV • DTV • Ext. • Component • HDMI Note The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Source List Use to select PC, TV or other external input source connected to the product.Use to select the screen of your choice. The direct button on the remote control is "SOURCE" button.
Adjusting the Monitor Edit Name Name the input device connected to the input jacks to make your input source selection easier • PC • VCR • DVD • D-VHS • Cable STB • HD STB • Satellite STB • AV Receiver • DVD Receiver • Game • Camcorder • DVD Combo • DHR
Troubleshooting Self-Test Feature Check Note • Check the following items yourself before calling for service. Contact the service center for problems that you cannot solve by yourself. • Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor.
Troubleshooting • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend a Samsung cleansing agent is used to prevent damage to the screen. 2. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repair of damages caused by him/her.
Troubleshooting PC Mode Q: It appears the PC does not function normally. A: Check if the Display Adapter Driver (VGA Driver) is properly installed. (Refer to Installing Driver) Q: The monitor screen flickers. A: Check if the signal cable between the computer and the monitor is securely connected and tightened.(Refer to Connecting the monitor) TV Mode Q: TV screen is blurred or shows noise signals. A: Check if the TV antenna connector is securely connected to the external antenna.
Troubleshooting A: Check if the resolution and frequency set for the computer video card falls in the range supported by the monitor. If not, reset them referring to the current Information under the monitor menu and Preset Timing Modes. Q: The image is too light or too dark A: Adjust the Brightness and Contrast.(Refer to the Brightness, Contrast) Q: Power Indicator blinks green. A: The monitor is currently saving the changes made in settings to the OSD memory.
Troubleshooting 5. You may see small particles if you look closely at the edge of the bezel surrounding the screen. This is part of the product’s design and is not a defect. Q&A Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. A: Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.
Troubleshooting Digital TV broadcasting allows you to easily access various information services in your home creating a more information-oriented home. Q: What is the difference between HDTV and SDTV? A: There are various types of digital TVs. A: The most widely known types of digital TV are HDTV and SDTV. They are classified according to the screen quality and the video specifications. • HDTV (High Definition TV): High screen quality, very clear TV.
Specifications General General Model Name SyncMaster T200HD LCD Panel Size 20 inch (51 cm) Display area 433.44 mm (H) x 270.9 mm (V) Pixel Pitch 0.258 mm (H) x 0.258 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Resolution Optimum resolution 1680 x 1050 @ 60 Hz Maximum resolution 1680 x 1050 @ 60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) 0.7 Vp-p ±5 % separate H/V sync, Composite TTL level (V high ≥ 2.0 V, V low ≤ 0.
Specifications Environmental considerations Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4 °F ~ 113 °F (-20 °C ~ 45 °C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Specifications LCD Panel Display area 473.76 mm (H) x 296.1 mm (V) Pixel Pitch 0.282 mm (H) x 0.282 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Resolution Optimum resolution 1680 x 1050 @ 60 Hz Maximum resolution 1680 x 1050 @ 60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) 0.7 Vp-p ±5 % separate H/V sync, Composite TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V) Maximum Pixel Clock 146.
Specifications Plug and Play Capability settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. • Resolution: 1680 x 1050 • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information and they are sent in HDTV objects appear heavier than in watching HDTV broadcast(16:9) mode. reality. ing. Note If temporary stops, mosaic screens, or jagged screens occur, this is not a TV problem. Contact your cable broadcasting company for a check-up. For information on how to connect and use your video, DVD, DVD combo, home theater, PC, etc., refer to their respective user manuals.
Information Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes. Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily.
Information Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean.
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.
Appendix Europe GERMANY 01805 - SAMSUNG (726-7864) http://www.samsung.com (€ 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com LUXEMBURG 0035 (0)2 261 03 710 http://www.samsung.com/be NETHERLANDS 0900 SAMSUNG (726-7864 € http://www.samsung.com/nl 0,10/Min) NORWAY 815-56 480 http://www.samsung.com/no POLAND 0 801 801 881 http://www.samsung.com/pl 022-607-93-33 PORTUGAL 80820-SAMSUNG (726-7864) http://www.samsung.
Appendix Asia Pacific TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com Middle East & Africa SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com U.A.E 800-SAMSUNG(726-7864) http://www.samsung.com 8000-4726 Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals.
Appendix curacy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen. Example: If the resolution is 1680(1920) x 1050(1200), this means the screen is composed of 1680(1920) horizontal dots (horizontal resolution) and 1050(1200) vertical lines (vertical resolution). RF Cable A round signal cable generally used for TV antennas.
Appendix A2 This system uses two carriers to transmit voice data. Countries such as South Korea and Germany use this system. BTSC Broadcast Television System CommitteeThe stereo broadcasting system that is used in most of the countries that have adopted the NTSC system, including the United States, Canada, Chile, Venezuela and Taiwan. It also refers to the organization that has been organized to promote its development and management. EIAJ Electronic Industries Association of Japan.
Appendix Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Europe only uct should not be mixed with other commercial wastes for disposal. Authority Information in this document is subject to change without notice. © 2008 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd.
