SyncMaster G19P Install drivers Install programs
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug. z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor.
Put down the monitor carefully. z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm/ 4 inchs ) for ventilation purposes.
Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.
could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center . z The monitor may malfunction, causing electric shock or fire. Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. z Failure to do so may cause electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable.
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports or etc. z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact a the Service Center. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.
product unplugged. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. z Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality. When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Quick Setup Guide Warranty Card (Not available in all locations) D-Sub Cable Power Cord Cable Sold separately DVI Cable Front User's Guide, Monitor Driver, Natural Color software
MENU / [ ]button Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™ [ ] MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
(The configuration at the back of the monitor may vary from product to product.) POWER IN DVI IN RGB IN Kensington Lock Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI IN port on the back of your monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system to something when using it in a public place.
Connecting the Monitor 1. Connect the power cord for your monitor to the POWER IN on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Use a connection appropriate for your computer. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [ RGB IN ] 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI IN port on the back of your Monitor.
Using the Stand Monitor Assembly Monitor and Bottom Folding the Base The monitor may be reclined -3 to 25 degrees. Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
4. If you can see following message window, then click the "Continue Anyway" button. Then click the "OK" button. (Microsoft® Windows® XP/2000 Operating System) This monitor driver is under certifying MS logo,and this installation dosen't damage your system.The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/. 5. Monitor driver installation is completed.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced." 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver." and select "Install from a list or." then click "Next" button. 6. Select "Don't search ,I will" then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose the "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon.
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. 2. 3. 4. 5. 6. 7. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard.
Uninstalling the Natural Color Software Program Select "Settings/Control Panel" from the "Start" menu and then double-click "Add/Delete a program." Select Natural Color from the list and then click the "Add/Delete" button.
1. [MENU/ ] Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu. 2. [ ] This button allows you to adjust items in the menu. 3. [ ] Press this button to activate a highlighted menu item. 4. [AUTO] Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
When pressing the MENU button after locking the OSD Menu Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the menu button for more than five seconds to activate the OSD adjustment lock function. Locked Unlock : Hold down the menu button for more than five seconds to deactivate the OSD adjustment lock function.
MagicBright™ Menu MagicBright™ Description Push the MagicBright button to circle through available preconfigured modes. - Six different modes (Custom/Text/Internet/Game/Sport/Movie) Brightness Menu Brightness Description When OSD is not on the screen, push the button to adjust brightness.
SOURCE Menu Description Selects the video signal while the OSD is off.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the [ ] button to adjust brightness. [MENU → Contrast → , → MENU] You can use the on-screen menus to change the contrast according to personal preference.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. MagicColor 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. 3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Menu Coarse Description Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only) [MENU → , → → → , → MENU] Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed).
Menu Description You can choose one of 9 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. [MENU → , H-Position → → , → → , → MENU] → → , → → , → MENU] → → , → → , → MENU] The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.
Menu Auto Source Description Select Auto Source for the monitor to automatically select the signal source. [MENU → , Image Reset → → , → MENU] Image parameters are replaced with the factory default values. [MENU → , Color Reset → → → , → → , → MENU] Color parameters are replaced with the factory default values.
Menu Information Description Shows a video source, display mode on the OSD screen.
Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
can handle properly. If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode","Recommended Mode 1280 x 1024 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode","Recommended Mode 1280 x 1024 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.
changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Settings. Has the video card been set properly? Set the video card by referring to the video card manual. Have you installed the monitor driver? Install the monitor driver according to the Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
General General Model Name SyncMaster G19P LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 31 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.2 M(6-bits+FRC) Resolution Optimum resolution 1280x1024@60Hz Maximum resolution 1280x1024@75Hz Input Signal, Terminated RGB Analog, Compliant Digital RGB 0.7 Vp-p ± 5% TTL level (V high ≥ 2.0V, V low ≤ 0.
Dimensions (WxHxD)/ Weight (With Stand) 419.9 X 426.6 X 210.0 mm / 16.5 x 16.8 x 8.3 inch / 6.3 kg / 13.9 lbs VESA Mounting Interface 75 x 75 mm Environmental considerations Operating Operating Temperature : 50 °F~ 104 °F ( 10 °C ~ 40 °C) Humidity : 10% ~ 80%, non-condensing Storage Storage Temperature : -4 °F~ 113 °F ( -20 °C ~ 45 °C) Humidity : 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
BELGIUM 02 201 2418 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805-121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.
PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) 8000-4726 http://www.samsung.
1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. { { Resolution: 1280 x 1024 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product.
416, Mae tan-3dong, Yeongtong - gu, Suwon City, Gyeonggi-do Korea
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
