User Manual SyncMaster C24A650X C27A650X C24A650U C27A650U The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality. © 2011 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics. Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation.
Before Using the Product Cleaning Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Take the following steps when cleaning. 1. Power off the monitor and computer. 2. Disconnect the power cord from the monitor. Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result. 3. Wipe the monitor with a clean, soft and dry cloth.
Before Using the Product Securing the Installation Space z Ensure some space around the product for ventilation. A rise in the internal temperature may cause a fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. The exterior may differ depending on the product. 10 cm 10 cm 10 cm 10 cm 10 cm Precautions for storage High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby.
Before Using the Product Warning Do not use a damaged power cord or plug, or a loose power socket. z An electric shock or fire may result. Do not plug many products into the same power socket. z Otherwise, the socket may overheat and cause a fire. Do not touch the power plug with wet hands. z Otherwise, an electric shock may result. Insert the power plug all the way in so it is not loose. z An unstable connection may cause a fire.
Before Using the Product Caution Do not unplug the power cord when the product is in use. z The product may become damaged by an electric shock. Do not use the power cord for products other than authorized products supplied by Samsung. z ! An electric shock or fire may result. Keep the power socket where the power cord is connected unobstructed. z If any problem occurs in the product, unplug the power cable to completely cut the power to the product.
Before Using the Product Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.). z The product may fall and break or cause a personal injury. z Using the product in an area with excess vibration may damage the product or cause a fire. Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke. z ! An electric shock or fire may result.
Before Using the Product Put down the product carefully. z The product may fall and break or cause a personal injury. ! SAMSUNG ! Installing the product in an unusual place (a place exposed to a lot of fine particles, chemical substances or extreme temperatures, or an airport or train station where the product should operate continuously for an extended period of time) may seriously affect its performance.
Before Using the Product Do not put a heavy object, toy, or sweets on top of the product. z The product or heavy objects may fall as children try to reach for the toy or sweets resulting in a serious injury. During a lightning or thunderstorm, remove the power cord and do not touch the antenna cable. z ! An electric shock or fire may result. Do not drop objects on the product or apply impact. z An electric shock or fire may result. ! Do not move the product by pulling the power cord or any cable.
Before Using the Product 100 Do not insert a metallic object (a chopstick, coin, hair pin, etc.) or inflammable object (paper, match, etc.) into the vent or ports of the product. z If water or any foreign substance enters the product, be sure to power off the product, remove the power cord, and contact Samsung Customer Service Center (107page). z Product failure, an electric shock or fire may result.
Before Using the Product Do not let water enter the DC power device or get the device wet. z An electric shock or fire may result. z Avoid using the product outdoors where it can be exposed to rain or snow. z Be careful not to get the DC power adapter wet when you wash the floor. Do not put the DC power adapter near to any heating apparatus. z Otherwise, a fire may result. Keep the DC power adapter in a well-ventilated area.
Before Using the Product Exercise caution when adjusting the product angle or stand height. ! z Otherwise, children's fingers or hands may become stuck and injured. z Tilting the product excessively may cause it to fall and result in personal injury. Do not place heavy objects on the product. z Product failure or personal injure may result. Correct posture to use the product Use the product in the correct posture as follows: z Straighten your back.
Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS USING "CENTRAL STATION" 2 Copyright 2 2 Icons used in this manual Symbols for safety precautions 3 Cleaning 3 4 4 Cleaning Securing the Installation Space Precautions for storage 4 Safety Precautions 4 6 8 Electricity and Safety Installation Operation 12 Correct posture to use the product 18 Checking the Contents 18 19 Removing the Packaging Checking the Components 21 Parts 21 23 Frontal Buttons Reverse Side 25 Installation
Table Of Contents CONNECTING AND USING A SOURCE DEVICE SCREEN SETUP 34 Connecting the Product to a PC to Use "Central Station" 34 38 Connecting to a PC via Wireless USB Connecting to a PC via the USB Cable 39 Utilizing "Central Station" 39 41 Using the Product as a USB HUB Connecting to a LAN 42 Configuring the Central Station Monitor IP 42 43 Dynamic IP Static IP 46 Notice before your use of Wireless USB or USB Mode 47 Before Connecting 47 Pre-connection Checkpoints 48 Connecting and
Table Of Contents CONFIGURING TINT RESIZING OR RELOCATING THE SCREEN 63 Coarse 63 Adjusting Coarse 64 Fine 64 Adjusting Fine 65 Response Time 65 Configuring Response Time 66 Red 66 Configuring Red 67 Green 67 Configuring Green 68 Blue 68 Configuring Blue 69 Color Tone 69 Configuring the Color Tone Settings 70 Gamma 70 Configuring Gamma 71 Image Size 71 Changing the Picture Size 72 H-Position & V-Position 72 Configuring H-Position & V-Position 73 Menu H-Position &
Table Of Contents SETUP AND RESET 74 HUB 74 75 76 77 78 79 79 Auto Wireless Detection Wireless Connection USB Connection Analog HDMI USB Super Charging Wireless ID 80 ECO 80 82 85 86 Eco Motion Sensor Eco Light Sensor Eco Saving Eco Icon Display 88 Menu Transparency 88 Changing Menu Transparency 89 Language 89 Changing the Language 90 PC/AV Mode 90 Configuring PC/AV Mode 91 Auto Source 91 Configuring Auto Source 92 Display Time 92 Configuring Display Time 93 Key Repeat Time 9
Table Of Contents INFORMATION MENU AND OTHERS TROUBLESHOOTING GUIDE SPECIFICATIONS APPENDIX 97 Reset 97 Initializing Settings (Reset) 98 INFORMATION 98 Displaying INFORMATION 98 Configuring Brightness in the Startup Screen 99 Requirements Before Contacting Samsung Customer Service Center 99 99 100 Testing the Product Checking the Resolution and Frequency Check the followings.
1 1.1 Preparations Checking the Contents 1.1.1 Removing the Packaging 1 Open the packaging box. Be careful not to damage the product when you open the packaging with a sharp instrument. 2 Remove the Styrofoam from the product. 3 Check the components and remove the Styrofoam and plastic bag. 4 z The appearance of actual components may differ from the image shown. z This image is for reference only. Store the box in a dry area so that it can be used when moving the product in the future.
1 Preparations 1.1.2 Checking the Components z Contact the dealer from whom you purchased the product if any item is missing. z The appearance of the components and items sold separately may differ from the image shown.
1 Preparations USB gender changer (Sold separately for C24A650U and C27A650U models) When the wireless-connection dongle cannot connect to your notebook PC, connect it using the USB gender changer. Items sold separately The following items can be purchased at your nearest retailer.
1 1.2 Preparations Parts 1.2.1 Frontal Buttons The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Icons Description z Open or close the onscreen display (OSD) menu, or return to the last menu. z OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings. To lock the OSD control, press the MENU button [ MENU ] for five seconds.
1 Preparations Icons Description Configure Customized Key and press [ HUB ]. The following options will be enabled. HUB HUB - ECO - MAGIC - Image Size To configure Customized Key, go to SETUP&RESET → Customized Key and select the mode you want. Move to the upper or lower menu or adjust the value for an option on the OSD menu. Adjust the screen brightness. Volume (VOL) can be adjusted if a cable is connected to the [HDMI IN] port. Confirm a menu selection.
1 Preparations 1.2.2 Reverse Side The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. DC 14V HDMI IN RGB IN LAN WIRELESS LAN ADAPTER Port Description Connects to the DC power adapter. Connects to a source device using an HDMI cable. Connects to a PC using the D-SUB cable. Connects to a network using the LAN cable. Connects to an audio output device such as headphones. Connects to a source device via a USB cable.
1 Preparations Port Description Connects to a PC via a USB cable. This port can only connect to a PC. Connect to the wireless-connection dongle (Rx).
1 1.3 Preparations Installation 1.3.1 Attaching the Stand Place a protective cloth or cushion on a flat surface. Next, place the product with the face down on top of the cloth or cushion. Insert the stand base into the stand in the direction of the arrow. Do not remove the fixing pin until you are finished attaching the stand. Tightly fasten the screw to the bottom of the base. After installing the stand, place the product upright. You can remove the fixing pin and adjust the stand now.
1 Preparations 1.3.2 Adjusting the Product Tilt and Height The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. z To adjust the height, remove the fixing pin. z The monitor tilt and height can be adjusted. z Hold the top center of the product and adjust the height carefully. 1.3.3 Rotating the Monitor You can rotate your monitor as shown below. z Be sure to fully extend the stand before rotating the monitor.
1 Preparations 1.3.
1 Preparations 1.3.5 Installing a Wall-mount Kit or Desktop Stand Before Installation Power the product off and remove the power cable from the power socket. Place a protective cloth or cushion on a flat surface. Next, place the product with the face down on top of the cloth or cushion. Unfasten the screw from the back of the product. Lift and detach the stand.
1 Preparations Notes z Using a screw longer than the standard length can damage the internal components of the product. z The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications. z Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit or desktop stand using excessive force. The product may get damaged or fall and cause personal injury.
1 1.4 Preparations "MagicRotation Auto" The "MagicRotation Auto" function detects the rotation of monitors that are fitted with a rotation sensor and rotates the Windows screen accordingly. [Software Installation] 1 2 Insert the user manual CD provided with the product into the CD-ROM drive. Follow the instructions given on the screen to proceed with installation. After installation, the on-screen display (OSD) menu will be displayed in the language of the operating system.
2 Using "Central Station" You can use the "Central Station" function by connecting the product to a PC through the Wireless USB function or a USB cable. "Central Station" allows the product to function as a HUB so that you can control a connected device from the product without having to connect to a PC. 2.
2 2.2 Using "Central Station" Software Installation for Using "Central Station" Install on your PC the software provided with the product. To maximize the performance of your Central Station monitor, visit www.samsung.com and upgrade the driver periodically. 2.2.1 Installing "Samsung Central Station Setup" This software is needed to use the Central Station function. Software installation may be affected by the graphics card, motherboard, or network conditions of the PC.
2 Using "Central Station" 6 After installing "Samsung Central Station Setup", customize the audio output port settings as required. Control Panel → Sound → Speakers → Configure Speakers 1 2 3 4 "Samsung Central Station Setup" software consists of "Samsung Wireless Central Station" and "Samsung Wireless Monitor". To delete the software, go to Start → Settings → Control Panel and double-click Add or Remove Programs on the PC.
2 2.3 Using "Central Station" Connecting the Product to a PC to Use "Central Station" Connect the product to a PC via Wireless USB and the USB cable. Connecting the product and PC via Wireless USB and the USB cable will allow you to hear audio when you plug headphones or speakers into [ ] on the product. (Not available when the D-SUB or HDMI-DVI cable is connected.) If a PC is connected, the product will automatically switch to the mode of the detected input source.
2 Using "Central Station" between the product and a PC. The dongle connected to a PC should point at the product to maximize signal reception. Wireless communication can be affected by the surrounding environmental conditions. Do not place an object, or obstacle, between the monitor and PC. The object can affect the sensitivity of the signal transmission/reception. z Ensure the receiver (dongle) on the Central Station monitor is at the same level and facing the transmitter (dongle) on the PC.
2 Using "Central Station" 3 Double-click the "Wireless Display Manager" icon created on the desktop. The following screen will appear. Five levels of signal intensity are available. All the five signal intensity indicator bars, including the green bar, will be lit when the strongest signal is received. The weakest signal intensity will turn on the red bar only. The following "Found New Hardware Wizard" screen may appear when the product attempts to connect to a PC via Wireless USB.
2 Using "Central Station" 5 Right-click on Connected Monitor to display the context menu as shown below. z Disconnect: Disconnect Wireless between the product and PC. z Set as default: Give first priority to the product to connect to the PC once a Wireless signal is detected. A star will appear beside the monitor icon if the product is set as the default monitor. z Rename: Customize the name of the connected monitor.
2 Using "Central Station" 2.3.2 Connecting to a PC via the USB Cable Connect the USB cable to [ ] on the back of the product and USB [ ] on the PC. A USB 2.0 cable can be used to connect the product to a PC. However, the PC should support USB 3.0 for the USB 3.0 function to work fully. Connecting to a PC using the USB cable 1 2 3 Connect a desktop PC to the product using the USB cable. Press [ ] to change the input source for the product to USB mode.
2 2.4 Using "Central Station" Utilizing "Central Station" Central Station is only available when the product is connected to a PC via Wireless USB or a USB cable. 2.4.1 Using the Product as a USB HUB Using the product as a hub, connect and use various source devices with the product at the same time. A PC cannot connect to multiple source devices at the same time as it has a limited number of input/ output ports available.
2 Using "Central Station" WIRELESS LAN ADAPTER Connect a mobile IT device such as an MP3 player or smart phone to the product when connected to a PC. This allows you to use the device from the PC or charge the battery on the device. z To charge the battery of a device, be sure to connect the device to the blue USB 3.0 port on the back of the product. z Battery charging is available in power-saving mode, but not available when the product is powered off.
2 Using "Central Station" 2.4.2 Connecting to a LAN "Central Station" allows you to use the Internet from a PC when you connect a LAN cable to the product (if the product is connected to the PC), without having to connect the LAN cable directly to the PC. This is achieved by an internal chip that transmits data received via the LAN cable to the PC as a converted USB signal.
2 2.5 Using "Central Station" Configuring the Central Station Monitor IP 1 After installing the integrated driver for Central Station monitors, go to Control Panel and Internet 2 → Network → Network and Sharing Center → Change adapter settings. You can see that the following two devices are displayed. a. The user PC’s network device b.
2 Using "Central Station" Go to Control Panel → Network and Internet → Network and Sharing Center → Change adapter settings. Next, right-click on the Central Station monitor’s network device (marked “LAN9512/LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”) and select Use. 3 Using the network properties menu, check that the IP address mode for the Central Station monitor’s network device is set to Auto.
2 Using "Central Station" Static IP User 1 2 Set the LAN network for the notebook PC to Do not use. Go to Control Panel → Network and Internet → Network and Sharing Center → Change adapter settings. Next, right-click on the notebook PC’s network device and select Do not use. 3 Right-click on the Central Station monitor’s network device (marked “LAN9512/LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”), and select Use. Be sure to perform this process before configuring the IP.
2 Using "Central Station" 5 After configuring the IP, click OK. The following message will appear. A static IP must be allotted to only one network device. The following message will appear if the same static IP is allotted to the network devices of both the notebook PC and Central Station monitor. (Ensure the network device that is not in use is set to Do not use.) Select No in the message window.
2 2.6 Using "Central Station" Notice before your use of Wireless USB or USB Mode 1 Most games require a high resolution and fast response time. When you play a game, it is recommended that you use Analog or HDMI mode instead of Wireless USB or USB mode. Note that playing a game or movie is not supported in Wireless USB or USB mode on a Windows XP or VISTA operating system.
3 3.1 Connecting and Using a Source Device Before Connecting 3.1.1 Pre-connection Checkpoints z Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. z Do not connect the power cable until all connections are completed. Connecting the power cable during connection may damage the product. z Check the types of ports at the back of the product you want to connect.
3 3.2 Connecting and Using a Source Device Connecting and Using a PC 3.2.1 Connecting to a PC z Select a connection method suitable for your PC. Connecting parts may differ in different products. Connection using the D-SUB cable (analogue type) RGB IN 1 Connect the D-SUB cable to the [RGB IN] port on the back of the product and the RGB port on the PC. 2 Connect the DC power adapter to the product and a power socket, and turn on the power switch on the PC. (For details, refer to "3.
3 Connecting and Using a Source Device Audio is not available if the PC and product are connected via the HDMI-DVI port. Connection Using an HDMI Cable (Digital Type) HDMI IN 1 Connect the HDMI cable to the [HDMI IN] port on the back of the product and the HDMI port on the PC. 2 Connect the DC power adapter to the product and a power socket, and turn on the power switch on the PC. (For details, refer to "3.4 Connecting the Power". ) 3 Press [ ] to change the input source to HDMI.
3 Connecting and Using a Source Device 3.2.2 Driver Installation z You can set the optimum resolution and frequency for this product by installing the corresponding drivers for this product. z An installation driver is contained on the CD supplied with the product. z If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com) and download the file. 1 2 3 4 Insert the user manual CD provided with the product into the CD-ROM drive.
3 Connecting and Using a Source Device 3.2.3 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language and change the resolution to the optimum value. The optimal resolution for this monitor is as follows: 1920 x 1080 60Hz Follow the above settings to set the resolution. English AUTO 1 2 Press [ ] to move to the language you want and press the [ ].
3 Connecting and Using a Source Device 3.2.4 Changing the Resolution Using a PC z Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. z The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel Display Settings and change the resolution.
3 Connecting and Using a Source Device Changing the Resolution on Windows Vista Go to Control Panel Personalization Display Settings and change the resolution.
3 Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution and change the resolution.
3 3.3 Connecting and Using a Source Device Connecting Headphones z Connect an audio output device such as headphones or speakers to [ ] on the product. Headphones will function properly if the product is connected to a PC via USB, Wireless USB or HDMI.
3 3.4 Connecting and Using a Source Device Connecting the Power Put the DC power adapter in the groove, with the switch facing upward. - Push the adapter until you hear a “click.” Connect the power cable to the DC power adapter. Next, connect the DC power adapter to the product. Plug in the power cable to the power socket. - Removing the DC power adapter To remove the DC power adapter, lift it outwards from the bottom as shown in the image.
4 4.1 Screen Setup Configure the screen settings such as brightness and color tone. MAGIC This feature provides the viewing angle, brightness, and tint to suit your preferences. 4.1.1 SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used. z z SAMSUNG Sub-options under MAGIC Bright may vary depending on the settings of "PC/AV Mode." (See "Chapter 7. SETUP&RESET.
4 Screen Setup z Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment. [In AV mode] MAGIC SAMSUNG MAGIC Bright SAMSUNG MAGIC Color : Dynamic Standard : Movie Custom Return 5 6 Adjust AUTO Enter z Dynamic: This mode is suitable when the ambient light is bright. z Standard: This mode is generally suitable for any environment. z Movie: This mode reduces eye fatigue. z Custom: Customize the contrast and brightness as required.
4 Screen Setup 4.1.2 SAMSUNG MAGIC Color SAMSUNG MAGICColor is a new picture-quality improvement technology developed independently by Samsung, which delivers vivid natural colors without picture quality degradation. SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. SAMSUNG Configuring MAGIC Color 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to PICTURE and press [ Press [ ] to move to MAGIC and press [ Press [ SAMSUNG ] on the product.
4 4.2 Screen Setup Brightness Adjust the general brightness of the picture. (Range: 0~100) A higher value will make the picture appear brighter. z SAMSUNG This menu is not available when MAGIC Bright is set to Dynamic Contrast mode. z This menu is not available when Eco Light Sensor or Eco Saving is set to On. 4.2.1 Configuring Brightness 1 2 3 Press [ MENU ] on the product. Press [ ] to move to PICTURE and press [ Press [ ] to move to Brightness and press [ ] on the product. ] on the product.
4 4.3 Screen Setup Contrast Adjust the contrast between the objects and background. (Range: 0~100) A higher value will increase the contrast to make the object appear clearer. z SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 4.3.1 Configuring Contrast 1 2 3 Press [ MENU ] on the product.
4 4.4 Screen Setup Sharpness Make the outline of objects more clear or blurry. (Range: 0~100) A higher value will make the outline of objects clearer. z SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 4.4.1 Configuring Sharpness 1 2 3 Press [ MENU ] on the product. Press [ ] to move to PICTURE and press [ Press [ ] to move to Sharpness and press [ ] on the product.
4 4.5 Screen Setup Coarse Adjust the screen frequency. Only available in Analog mode. 4.5.1 Adjusting Coarse 1 2 3 Press [ MENU ] on the product. Press [ ] to move to PICTURE and press [ Press [ ] to move to Coarse and press [ ] on the product. ] on the product. The following screen will appear. PICTURE MAGIC Brightness 50 Contrast 75 Sharpness 60 Coarse 2200 Fine 0 Response Time Faster Return 4 Adjust the Coarse using the [ Adjust AUTO Enter ] button.
4 4.6 Screen Setup Fine Fine-adjust the screen to obtain a vivid picture. Only available in Analog mode. 4.6.1 Adjusting Fine 1 2 3 Press [ MENU ] on the product. Press [ ] to move to PICTURE and press [ Press [ ] to move to Fine and press [ ] on the product. ] on the product. The following screen will appear.
4 4.7 Screen Setup Response Time Accelerate the panel response rate to make video appear more vivid and natural. z It is best to set Response Time to Normal or Faster when you are not viewing a movie. z The functions available on the monitor may vary depending on the model. Refer to the actual product. 4.7.1 Configuring Response Time 1 2 3 Press [ MENU ] on the product. Press [ ] to move to PICTURE and press [ ] on the product. Press [ ] to move to Response Time and press [ ] on the product.
5 Configuring Tint SAMSUNG Adjust the tint of the screen. This menu is not available when MAGIC Bright is set to Cinema or Dynamic Contrast mode. Red Adjust the value of the color red in the picture. (Range: 0~100) A higher value will increase the intensity of the color. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 5.1.1 Configuring Red 1 2 3 Press [ MENU ] on the product.
5 Green Adjust the value of the color green in the picture. (Range: 0~100) A higher value will increase the intensity of the color. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 5.2.1 Configuring Green 1 2 3 Press [ MENU ] on the product. Press [ ] to move to COLOR and press [ Press [ ] to move to Green and press [ ] on the product. ] on the product. The following screen will appear. COLOR Red 50 Green 50 Blue Color Tone Normal Gamma 5.
5 Blue Adjust the value of the color blue in the picture. (Range: 0~100) A higher value will increase the intensity of the color. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 5.3.1 Configuring Blue 1 2 3 Press [ MENU ] on the product. Press [ ] to move to COLOR and press [ Press [ ] to move to Blue and press [ ] on the product. ] on the product. The following screen will appear. COLOR Red 50 Green 50 Blue Color Tone Normal Gamma 5.
5 Color Tone Adjust the general color tone of the picture. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 5.4.1 Configuring the Color Tone Settings 1 2 3 Press [ MENU ] on the product. Press [ ] to move to COLOR and press [ Press [ ] to move to Color Tone and press [ ] on the product. ] on the product. The following screen will appear. COLOR Red Green 50 Blue 50 Color Tone Gamma 5.
5 Gamma Adjust the mid-range brightness (Gamma) of the picture. 5.5.1 Configuring Gamma 1 2 3 Press [ MENU ] on the product. Press [ ] to move to COLOR and press [ ] on the product. Press [ ] to move to Gamma and press [ ] on the product. The following screen will appear. COLOR Red 50 Green 50 Blue Color Tone Normal Gamma 5.5 Configuring Tint Mode1 Mode2 Mode3 50 AUTO 4 5 Press [ ] to move to the option you want and press the [ ].
6 6.1 Resizing or Relocating the Screen Image Size Change the picture size. 6.1.1 Changing the Picture Size 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SIZE&POSITION and press [ Press [ ] to move to Image Size and press [ ] on the product. ] on the product. The following screen will appear.
6 6.2 Resizing or Relocating the Screen H-Position & V-Position H-Position: Move the screen to the left or right. V-Position: Move the screen up or down. z This menu is only available when Image Size is set to Screen Fit. z Only available in Analog mode. 6.2.1 Configuring H-Position & V-Position 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SIZE&POSITION and press [ ] on the product. Press [ ] to move to H-Position or V-Position, and press [ ]. The following screen will appear.
6 6.3 Resizing or Relocating the Screen Menu H-Position & Menu V-Position Menu H-Position: Move the menu position to the left or right. Menu V-Position: Move the menu position up or down. 6.3.1 Configuring Menu H-Position & Menu V-Position 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SIZE&POSITION and press [ ] on the product. Press [ ] to move to Menu H-Position or Menu V-Position, and press [ ]. The following screen will appear.
7 7.1 Setup and Reset HUB Configure the settings to use the HUB function on the product. Refer to "Chapter 2. Central Station" for details about how to use the HUB function. 7.1.1 Auto Wireless Detection If the product is connected to a PC via Wireless USB, it will automatically detect the Wireless USB signal and change the input source to Wireless USB mode. Configuring Auto Wireless Detection 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ ] on the product.
7 Setup and Reset 7.1.2 Wireless Connection You can view the status of the Wireless USB connection between the product and a PC. Selecting the Wireless Connection option. The input source will change to Wireless USB mode. z The connection status will be shown even when the input source is not Wireless USB mode. z Selecting Wireless Connection when a Wireless USB connection is established will automatically change the input source to Wireless USB mode.
7 Setup and Reset 7.1.3 USB Connection You can view the USB cable connection status between the product and a PC. z The connection status will be shown even when the input source is not USB mode. z Selecting USB Connection when a USB cable is connected will automatically change the input source to USB mode. Configuring USB Connection 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to HUB and press [ ] on the product. ] on the product.
7 Setup and Reset 7.1.4 Analog You can view the Analog cable connection status between the product and a PC. z The connection status will be shown even when the input source is not Analog mode. z Selecting the Analog option when an analog cable is connected will automatically change the input source to Analog mode. Configuring Analog 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to HUB and press [ ] on the product. ] on the product.
7 Setup and Reset 7.1.5 HDMI You can view the HDMI connection status between the product and an AV device. z The connection status will be shown even when the input source is not HDMI mode. z Selecting the HDMI option when an HDMI cable is connected will automatically change the input source to HDMI mode. Configuring HDMI 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to HUB and press [ ] on the product. ] on the product.
7 Setup and Reset 7.1.6 USB Super Charging A source device's battery can be charged quickly via USB 3.0 port on the product. z Data transmission is not available if USB Super Charging is on. z To enable standard charging or data transmission, set USB Super Charging to off. z The input source does not need to be changed. Configuring USB Super Charging 1 2 3 4 Press [ MENU ] on the product.
7 7.2 Setup and Reset ECO The Eco Motion Sensor, Eco Light Sensor, and Eco Saving options are displayed on the same menu page so that you can conveniently configure the power saving settings. 7.2.1 Eco Motion Sensor The Eco Motion Sensor activates to save power when it does not detect any movement within a specified area for a specified period of time. Eco Motion Sensor is not available when the monitor is used in portrait mode. Configuring Eco Motion Sensor 1 2 3 4 Press [ MENU ] on the product.
7 Setup and Reset Configuring Backlight 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Backlight and press [ ] on the product. ] on the product. ] on the product. The following screen will appear.
7 Setup and Reset 7.2.2 Eco Light Sensor The Eco Light Sensor feature optimizes the view condition and contributes to power saving by adjusting the screen brightness depending on the ambient light intensity. z SAMSUNG This menu is not available when MAGIC Bright is in Dynamic Contrast mode. z This menu is not available when Eco Saving is set . Configuring Eco Light Sensor 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ ] on the product.
7 Setup and Reset Configuring Sensitivity 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Sensitivity and press [ ] on the product. ] on the product. ] on the product. The following screen will appear.
7 Setup and Reset Configuring Brightness Level 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Brightness Level and press [ ] on the product. ] on the product. ] on the product. The following screen will appear.
7 Setup and Reset 7.2.3 Eco Saving The Eco Saving function reduces power consumption by controlling the electric current used by the monitor panel. z SAMSUNG This menu is not available when MAGIC Bright is in Dynamic Contrast mode. z This menu is not available when Eco Light Sensor is set. Configuring Eco Saving 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Eco Saving and press [ ] on the product.
7 Setup and Reset 7.2.4 Eco Icon Display Configuring Eco Icon Display 1 2 3 4 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ ] on the product. Press [ ] to move to ECO and press [ Press [ ] to move to Eco Icon Display and press [ ] on the product. ]. The following screen will appear.
7 Setup and Reset will decrease with a moon image displayed. The brightness slide bar will be displayed for 3 seconds after the sensor activates. You've saved * tree(s). z A pop-up as shown above will appear when an energy tree completes while Eco Icon Display is On. If the above picture is displayed, it means the Eco Icon Display option is On. Change this setting to Off if you do not want to display the pop-up.
7 7.3 Setup and Reset Menu Transparency Set the transparency for the menu windows: 7.3.1 Changing Menu Transparency 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Menu Transparency and press [ ] on the product. ] on the product. The following screen will appear.
7 7.4 Setup and Reset Language Set the menu language. z A change to the language setting will only be applied to the onscreen menu display. z It will not be applied to other functions on your PC. 7.4.1 Changing the Language 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Language and press [ ] on the product. ] on the product. The following screen will appear.
7 7.5 Setup and Reset PC/AV Mode Set PC/AV Mode to AV. The picture size will be enlarged. This option is useful when you view a movie. PC/AV Mode is only available in HDMI mode. 7.5.1 Configuring PC/AV Mode 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to PC/AV Mode and press [ ] on the product. ] on the product. The following screen will appear.
7 7.6 Setup and Reset Auto Source Activate Auto Source. 7.6.1 Configuring Auto Source 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Auto Source and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET HUB ECO Menu Transparency On Language English PC/AV Mode PC Auto Source Auto Manual Display Time Return 4 5 Move z Auto: The input source is automatically recognized.
7 7.7 Setup and Reset Display Time Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified period of time. Display Time can be used to specify the time after which you want the OSD menu to disappear. 7.7.1 Configuring Display Time 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Display Time and press [ ] on the product. ] on the product. The following screen will appear.
7 7.8 Setup and Reset Key Repeat Time Control the response rate of a button when the button is pressed. 7.8.1 Configuring Key Repeat Time 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Key Repeat Time and press [ ] on the product. ] on the product. The following screen will appear.
7 7.9 Setup and Reset Customized Key You can customize Customized Key as follows. 7.9.1 Configuring Customized Key 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ ] on the product. Press [ ] to move to Customized Key and press [ ] on the product. The following screen will appear.
7 Setup and Reset 7.10 Off Timer On/Off Enable or disable the off timer that automatically powers off the product. 7.10.1 Configuring Off Timer On/Off 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ ] on the product. Press [ ] to move to Off Timer On/Off and press [ ] on the product. The following screen will appear.
7 Setup and Reset 7.11 Off Timer Setting The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number of hours. This menu is only available when Off Timer On/Off is set to On. 7.11.1 Configuring Off Timer Setting 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ ] on the product. Press [ ] to move to Off Timer Setting and press [ ] on the product. The following screen will appear.
7 Setup and Reset 7.12 Reset Return all the settings for the product to the default factory settings. 7.12.1 Initializing Settings (Reset) 1 2 3 Press [ MENU ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Reset and press [ ] on the product. ] on the product. The following screen will appear.
8 8.1 INFORMATION Menu and Others INFORMATION View the current input source, frequency and resolution. 8.1.1 Displaying INFORMATION 1 2 Press [ MENU ] on the product. Press [ ] to move to INFORMATION. The current input source, frequency and resolution will appear. PICTURE COLOR Analog SIZE&POSITION 67.6kHz 60Hz PP 1920 x 1080 SETUP&RESET INFORMATION EXIT Exit 8.
9 9.1 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center 9.1.1 Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check if your product is operating normally by using the product test function. If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC, perform a self-diagnosis test.
9 Troubleshooting Guide 9.1.3 Check the followings. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure. (Refer to "3.2 Connecting and Using a PC") Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the monitor and PC. The blank spaces found on the screen have nothing to do with the monitor.
9 Troubleshooting Guide Screen issue The screen appears unstable and shaky. There are shadows or ghost images left on the screen. Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product, and if required, change the settings, referring to Standard Signal Mode Table (106page) in this manual and the INFORMATION menu on the product. The screen is too bright. The screen is too dark. Adjust Brightness(60page) and Contrast(61page).
9 9.2 Troubleshooting Guide Q&A Question How can I change the frequency? Answer Set the frequency on your graphics card. z Windows XP: Select Control Panel Display Settings Appearance and Themes Advanced Monitor, and adjust Refresh rate under Monitor settings. z Windows ME/2000: Select Control Panel Advanced z Settings Monitor, and adjust Refresh rate under Monitor settings.
10 Specifications 10.1 General Model Name Panel Synchronization C27A650X / C27A650U Size 24 inches (61 cm) 27 inches (68 cm) Display area 531.36 mm (H) x 298.89 mm (V) 597.6 mm (H) x 336.15 mm (V) 20.9 inches (H) x 11.8 inches (V) 23.5 inches (H) x 13.2 inches (V) Horizontal Frequency 30~81 kHz Vertical Frequency 56~75 Hz Display Color Resolution C24A650X / C24A650U 16.
10 Specifications Class B device (broadcast communications device for home use) This Class B device designed for home use is registered for EMC requirements and can be used in all regions. (USA Only) Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website, www.samsung.
10 Specifications 10.2 PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power-savign mode only functions when the product is connected to a PC with a power-saving function.
10 Specifications 10.3 Standard Signal Mode Table z This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Therefore, a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for the screen size of your product. z Check the frequency when you exchange a CDT monitor (connected to a PC) for an LCD monitor.
Appendix Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com LATIN AMERICA ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 4004-0000 http://www.samsung.com CHILE 800-SAMSUNG (726-7864) http://www.samsung.
Appendix ASIA PACIFIC HONG KONG (852) 3698 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 3030 8282, 1800 3000 8282 http://www.samsung.com INDONESIA 0800-112-8888 021-5699-7777 http://www.samsung.com JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com PHILIPPINES 1-800-10-SAMSUNG (726-7864) 1-800-3-SAMSUNG (726-7864) 1-800-8-SAMSUNG (726-7864) 02-5805777 http://www.samsung.com SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.
Appendix Terminology OSD(On Screen Display) On screen display (OSD) allows you to configure on-screen settings to optimize the picture quality as required. It allows you to change the screen brightness, tint, size and many other settings using menus displayed on the screen. HUB HUB refers to a device that is a common connection point for multiple devices connected over a network. It is used to connect multiple PCs, video devices, office devices and/or LANs over a single network.
Appendix the screen refreshes 60 times per second. The screen scanning rate depends on the performance of the graphics cards in your PC and monitor. Horizontal Frequency Characters or images displayed on the monitor screen consist of numerous dots (pixels). Pixels are transmitted in horizontal lines, which are then arranged vertically to create an image.
Index A G About "Central Station" 31 Gamma 70 Appendix 107 General 103 Auto Source 91 Green 67 B H Before Connecting 47 HUB 74 Blue 68 Brightness 60 I Image Size 71 C INFORMATION 98 Checking the Contents 18 Installing the Product 25 Cleaning 3 Coarse 63 Color Tone 69 K Key Repeat Time 93 Configuring Brightness in the Startup Screen 98 Configuring the Central Station Monitor IP 42 L Connecting and Using a PC 48 Languagey 89 Connecting Headphones 55 Connecting the Product to a PC to
Index PC/AV Mode 90 PowerSaver 105 Q Q & A 102 R Red 66 Requirements Before Contacting Samsung Customer Service Center 99 Reset 97 Response Time 65 S Safety Precautions 4 Sharpness 62 Software Installation for Using "Central Station" 32 Standard Signal Mode Table 106 T Terminology 109 U Utilizing "Central Station" 39 Index 112
