User’s Manual Index Main Page On-Screen Display General Highlight Zone Safety Instructions Troubleshooting Natational Check List Power Q&A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Unpacking General Specifications Front Preset Display Modes Rear PowerSaver Bottom Setup Information Connecting Your Monitor Service Installing the Monitor Driver Terms — Windows 2000 Regulatory — Other Operating System Natural Color Base Installation Authority
User’s Manual 3 Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
User’s Manual 4 Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the flourescent substance on the inside of the CDT. • Do not use a damaged or loose plug. • • Do not pull the plug out by the wire nor touch the plug with wet hands.
User’s Manual 5 Safety Instructions Power • Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. • • Failure to do so may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. • This may cause a fire.
User’s Manual Safety Instructions Installation • Do not cover the vents on the monitor cabinet. • • Put your monitor in a location with low humidity and a minimum of dust. • • This may cause damage to the product or human body. Place the monitor on a flat and stable surface. • • An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. • • Bad ventilation may cause a breakdown or fire. The monitor can cause injury by falling.
User’s Manual 7 Safety Instructions Installation • Do not place the monitor face down. • • The CDT surface may be damaged. Do not use the monitor without the monitor stand. • • It could break down or cause a fire due to bad ventilation. If the monitor must be used without the supplied stand, take steps to insure proper ventilation.
User’s Manual 8 Safety Instructions Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using.
User’s Manual 9 Safety Instructions Other • Do not remove cover(or back). No user serviceable parts inside. • • • If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. • • This may cause an electric shock or a fire. For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. • • This may cause an electric shock or a fire.
User’s Manual 10 Safety Instructions Other • Do not try to move the monitor by pulling on the wire or the signal cable. • • Do not move the monitor right or left by pulling only the wire or the signal cable. • • This may cause a breakdown, electric shock or a fire due to damage to the cable. Never insert anything metallic into the monitor openings. • • This may cause a breakdown, electric shock or a fire due to damage to the cable. This may cause an electric shock, fire or injury.
User’s Manual Introduction Unparking • Monitor and Stand (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
User’s Manual 12 Introduction Front The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. Use this button to Exit the active menu or the OSD. 2. Exit button These buttons allow you to highlight and adjust items in the menu. 3. Adjust buttons Use this button to open the OSD and activate a highlighted menu item. 4. Menu button This light glows green during normal operation, and blinks amber once as the 5.
User’s Manual 13 Introduction Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal Cable Note: Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. See Connecting Your Monitor for further information regarding cable connections.
User’s Manual 14 Introduction Bottom 1. Signal Cable 2. Power Port 3. Tilt/Swivel Base Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Connect the power cord for your monitor to the power port on the back of the monitor. You can separate the base from the monitor.
User’s Manual 15 Setup Connecting Your Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter (Adapter not included). A PC-compatible computer does not need an adapter.
Setup When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungmonitor.com/ (USA) http://www.sec.co.kr/ (Korea) http://www.
Setup Windows XP/2000 1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button. 4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.
Setup When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.com/ (Europe) http://www.samsungmonitor.com/ (USA) http://www.sec.co.kr/ (Korea) http://www.
Setup 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
Setup This is your Thi monitor it driver di i under d certifying tif i MS logo,and l d this thi installation i t ll ti don't d 't damage d system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1.
Setup Microsoft® Windows® Millennium Operating System 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location.." then click "Next" button.
Setup 7. C Continue choosing "Close"" b button button the "Di "Display 7 ti h i "Cl tt and d "OK" b tt until til you close l th l Properties" dialogue box. Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4.
User’s Manual Setup Base Installation Tilt/Swivel Base With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. Note: The base is detachable.
User’s Manual 22 Setup Base Installation Attaching and Removing the Bose 1 Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3.Press the base onto the monitor until the tabs are fully engaged in the slots. 4. Push the base toward the front of the monitor until the release latch clicks into the locked position. * Do not bend the snap.
User’s Manual 23 Setup Base Installation Attaching and Removing the Bose 2 Removing the Base 5. Squeeze and pull up on the release latch on the base. Note: 6. Push the base toward the back of the monitor and lift up to remove the base. The base will align with the monitor slots in only one position.
User’s Manual On-Screen Display 1. Highlight button: The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. 2. Exit button: Use this button to Exit the active menu or the OSD. 3. Adjust buttons: These buttons allow you to highlight and adjust items in the menu. 4. Menu button: Use this button to open the OSD and activate a highlighted menu item.
User’s Manual 25 On-Screen Display Menu How to adjust Brightness/Contrast Adjust Brightness and Contrast. 1 2 Push the ◀▶ ( ◑ ) or ▲ ▼ ( ) button. The brightness/contrast display will appear. Push the ▲ button to increase the brightness or the ▼ button to decrease the brightness. Push the ◀ button to increase the contrast or the ▶ button to decrease the contrast. OSD lock/unlock 1 2 Push and hold in the Menu ( ) button for 10 seconds or more to Lock the OSD.
User’s Manual 26 On-Screen Display Menu How to adjust Position Follow these instructions to change the Position of the monitor's entire display. 1 2 3 Push the Menu( ) button. Push the Menu( ) button to open the Position adjustment screen. Use the ▲ and ▼ buttons to change the vertical position of the monitor's viewing area; use the ◀ and ▶ buttons to change the horizontal position of the monitor's viewing area. Size Follow these instructions to change the size of the monitor's entire display.
User’s Manual 27 On-Screen Display Menu How to adjust Zoom Follow these instructions to get a close-up or a longshot view of the monitor's viewing area. 1 2 3 4 Push the Menu ( ) button. Push the ◀ button or ▶ button until the Position/Size screen is displayed. Push the ▲ button or ▼ button to select zoom. Push the Menu ( ) button to open the zoom adjustment screen. Use the ◀ button to decrease the screen viewing area. Use the ▶ button to enlarge the screen viewing area.
User’s Manual 28 On-Screen Display Menu How to adjust Pincushion/Trapezoid Adjust the pincushion setting when the sides of the display are bowed in or bowed out; adjust the trapezoid setting when the top or bottom of the display is too large or small. 1 2 3 4 Push the Menu ( ) button. Push the ◀ button or ▶ button until the Geometry screen is displayed. push the▲ button or ▼ button to select Pincushion/Trapezoid. Push the Menu ( ) button to open the Pincushion/Trapezoid adjustment screen.
User’s Manual 29 On-Screen Display Menu How to adjust Linearity Adjust the linearity setting when the display image is compressed at the left,right or top,bottom. 1 2 3 4 Push the Menu ( ) button. Push the ◀ button or ▶ button until the Geometry screen is displayed. Push the ▲ button or ▼ button to select Linearity. Push the Menu ( ) button to open the Linearity adjustment screen. Use the ◀ button or ▶ button to adjust the vertical Linearity.
User’s Manual 30 On-Screen Display Menu How to adjust 9300K/6500K Color temperature is a measure of the "Warmth"of the image colors. The available range is between 6500 to 9300K. 1 2 3 Push the Menu ( ) button. Push the ◀ button or ▶ button until the Color screen is displayed. Push the ▲ button or ▼ button to select 9300K (Bluish colors) or 6500K (Reddish colors). Clear Moire A 'moiré' pattern can appear on your screen, looking like a series of concentric circles or arcs.
User’s Manual 31 On-Screen Display Menu How to adjust Degauss The Degauss feature will remove color impurities caused by magnetic fields. Do not use the Degauss feature more than once within a 30-minute period. Note: The monitor may buzz momentarily, the image colors may change and the image will jiggle for a few seconds. These effects are normal. 1 2 3 Push the Menu ( ) button. Push the ◀ button or ▶ button until the Advanced screen is displayed.
User’s Manual 32 On-Screen Display Menu How to adjust Video Input Level Some video cards use video signals higher than 1.0V which causes the display to be very bright. For those video cards, use this feature to select the 1.0 V Level. 1 2 3 4 Push the Menu ( ) button. Push the ◀ button or ▶ button until the Advanced screen is displayed. Push the ▲ button or ▼ button to select Video Input Level. Push the Menu ( ) button to open the Video Input Level selection screen. Use the ◀ or ▶ buttons to select 0.
User’s Manual 33 On-Screen Display Menu How to adjust Menu Duration The menu will automatically turn off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it turns off. 1 2 3 4 Push the Menu ( ) button. Push the ◀ button or ▶ button until the Menu screen is displayed. Push the ▲ button or ▼ button to select Menu Duration. Push the Menu ( ) button to open the Menu Duration selection screen.
User’s Manual 34 On-Screen Display Menu How to adjust Menu Color 1 2 3 4 Push the ( ) button. Push the ◀ button or ▶ button until the 'Menu' screen is displayed. Push the ▲ button or ▼ button to select Menu Color. Push the Menu ( ) button to open the Menu Color selection screen. Use the ▲ button or ▼ button to select Menu Color 1 or Menu Color 2. Halftone Use this function to see the transparent on-screen display. 1 2 3 4 Push the Menu ( ) button.
User’s Manual 35 On-Screen Display Menu How to adjust Highlight This function is to execute or cancel the Highlight Zone. 1 2 3 Push the Highlight ( ) button. Push the Menu ( ) button. Push the ◀ button or ▶ button to cancel, execute or enlarge the entire screen. Position This function is to move the Highlight Zone horizontally or vertically. 1 2 3 Push the Highlight ( ) button. Push the◀button or▶button to select the Screen Position Adjustment and then push the Menu ( ) button.
User’s Manual 36 On-Screen Display Menu How to adjust Size This function is to adjust the size of the Highlight Zone. 1 2 3 Push the Highlight ( ) button. Push the ◀ button or ▶ button to select the Screen Size Adjustment and then push the Menu ( ) button. Push the ◀ button or ▶ button to move the size of the Highlight Zone horizontally and use the push the ▲ button or ▼ button to move it vertically. Contrast This function is to use the Contrast of the Highlight Zone.
User’s Manual 37 On-Screen Display Menu How to adjust Color This function is to adjust the color of the Highlight Zone. 1 2 3 Push the Highlight ( ) button. Push the ◀ button or ▶ button to select the Color Adjustment and then push the Menu ( ) button. Push the ▲ button or ▼ button to select a color from R, G or B. Push the ◀ button or ▶ button to adjust the R, G or B color of the Highlight Zone. Zoom This function is to enlarge or reduce the Highlight Zone. 1 2 3 Push the Highlight ( ) button.
User’s Manual 38 On-Screen Display Menu How to adjust Sharpness This function is to adjust the sharpness of the Highlight Zone. 1 2 3 Push the Highlight ( ) button. Push the ◀ button or ▶ button to select the Sharpness Adjustment and then push the Menu ( ) button Push the ◀ button or ▶ button to adjust the sharpness of the Highlight Zone.
User’s Manual 39 Troubleshooting Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Symptom Check List Solutions No images on the screen. I cannot turn on the monitor. Is the power cord connected properly? Check the power cord connection and supply.
User’s Manual 40 Troubleshooting Check List Symptom The image on the screen is shaking. Check List Solutions Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) The signal from the video card exceeds the maximum resolution and frequency of the monitor. Are there any magnetic products such as a power adapter, speaker or a high voltage wire near by? Move the monitor away from anything that can create a strong magnetic field.
User’s Manual Troubleshooting Check List Symptom Check List Solutions The screen is partially distorted. Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor? Enter the OSD and perform a "Degauss". Keep the monitor away from any magnetic products. LED is blinking but no images on the screen.
User’s Manual 42 Troubleshooting Check List Check the following items if there is trouble with the monitor. 1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. 4.
User’s Manual 43 Troubleshooting Q&A Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows 95/98: Set the resolution at the Control Panel, Display, Settings. Windows 3.1: Change the resolution and the colors using the VGA Utility provided by the video card.
User’s Manual 44 Troubleshooting Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. . 3. Turn on the monitor. If your monitor works normally, the following screen appears. Failure of any of the boxes to appear indicates a problem with your monitor.
User’s Manual 45 Troubleshooting Self-Test Feature Check Werning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1.
Specifications General General Model Name SyncMaster 955b Picture Tube Type 19"(48cm) Full square type (45.8cm viewable) Deflection angle 90° Dot Pitch 0.22 mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask.
Specifications General Maximum Pixel Clock 185 MHz Power Supply 90 ~ 264VAC, 60/50 Hz ± 3Hz Power Consumption 110W (Max), 100W (Nom) Dimensions (WxDxH) 440x454x461mm (with Stand) Weight 19.0 kg Environmental considerations Operating Temperature: 32°F ~ 104°F(0°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Specifications General General Model Name SyncMaster 950b Picture Tube Type 19"(48cm) Full square type (45.8cm viewable) Deflection angle 90° Dot Pitch 0.22 mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask.
Specifications General Maximum Pixel Clock 185 MHz Power Supply 90 ~ 264VAC, 60/50 Hz ± 3Hz Power Consumption 110W (Max), 100W (Nom) Dimensions (WxDxH) 440x454x461mm (with Stand) Weight 19.0 kg Environmental considerations Operating Temperature: 32°F ~ 104°F(0°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.
Specifications PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
Specifications General General Model Name SyncMaster 955DF Picture Tube Type 19"(48cm) DynaFlat (45.8cm viewable) Deflection angle 90° Dot Pitch 0.22 mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask.
Specifications General Maximum Pixel Clock 185 MHz Power Supply 90 ~ 264VAC, 60/50 Hz ± 3Hz Power Consumption 110W (Max), 100W (Nom) Dimensions (WxDxH) 440x460x461mm (with Stand) Weight 21.0 kg Environmental considerations Operating Temperature: 32°F ~ 104°F(0°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.
Specifications PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
Specifications General Model Name SyncMaster 763DFX Picture Tube Type 17"(43cm) DynaFlat X (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask.
Specifications Storage Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice.
Specifications This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
Specifications If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.
Specifications General Model Name SyncMaster 765DFX Picture Tube Type 17"(43cm) DynaFlat X (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask.
Specifications Storage Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice.
Specifications This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
Specifications If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.
User’s Manual 52 Information Service ● U.S.A. Samsung Computer Products Customer Service 400 Valley Road, Suite 201, Mt. Arlington, NJ 07856 Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864) Fax. : (973)601-6001 http://samsungmonitor.com/ ● BRAZIL Samsung Eletronica da Amazonia Ltda.R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ ● CANADA Samsung Electronics Canada Inc.
User’s Manual 53 Information Terms • Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm • Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
User’s Manual 54 Information Regulatory • FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User’s Manual 55 Information Regulatory • IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numérique de classe Brespecte toutes les exigences du R?glemont ICES-003 sur les équipements produisant des interférences au Canada. • MPR II Compliance • European Notice (Europe only) This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. . . . . .
User’s Manual 56 Information Regulatory • TCO'95-Ecological requirements for personal computers (TCO applied model only) AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
User’s Manual 57 Information Regulatory TCO Development Unit 1996-11-29 On the page this folder you will find a brief summary of the environmental requirements met by this product. The complere environmental criteria document may be ordered from: TCO Development Unit S-11494 Stockholm Sweden Fax: +46 8 782 92 07 E-mail (Internet): development@tco.se Current information regarding TCO'95-approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.
User’s Manual 58 Information Regulatory • TCO'99-Ecological requirements for personal computers (TCO applied model only) Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
User’s Manual 59 Information Regulatory TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire.
User’s Manual 60 Information Natural Color • Natural Color Software Program Die Natural Color S/W ist die Lösung für dieses Problem. Dieses Programm ist ein Farbverwaltungssystem, daß von Samsung Electronics mit Zusammenarbeit von Korea Electronics & Telecommunications Forschungsinstitut (ETRI) entwickelt wurde. Dieses System ist nur bei einem Samsung Monitor anwendbar und ermöglicht, daß die Farbe des Bildes auf dem Monitor den gleichen Effekt zeigt, wie auf dem gedruckten bzw. gescannten Bild.
User’s Manual 61 Information Authority Information in this document is subject to change without notice. ⓒ 2001 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
