User Manual SyncMaster S27A850D The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality. ⓒ 2011 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics. Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation.
Before Using the Product Icons used in this manual The following images are for reference only. Real-life situations may differ from what is shown in the images. Symbols for safety precautions A serious or fatal injury may result if instructions are not followed. Warning Caution Personal injury or damage to properties may result if instructions are not followed. Activities marked by this symbol are prohibited. Instructions marked by this symbol must be followed.
Before Using the Product Cleaning Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Take the following steps when cleaning. 1. Power off the monitor and computer. 2. Disconnect the power cord from the monitor. Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result. 3. Wipe the monitor with a clean, soft and dry cloth.
Before Using the Product Securing the Installation Space z Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. The exterior may differ depending on the product. 10 cm 10 cm 10 cm 10 cm 10 cm Precautions for storage High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby.
Before Using the Product Safety Precautions Electricity and Safety The following images are for reference only. Real-life situations may differ from what is shown in the images. Warning Do not use a damaged power cord or plug, or a loose power socket. z An electric shock or fire may result. Do not plug many products into the same power socket. z Otherwise, the socket may overheat and cause a fire. Do not touch the power plug with wet hands. z Otherwise, an electric shock may result.
Before Using the Product Caution Do not unplug the power cord when the product is in use. z The product may become damaged by an electric shock. Do not use the power cord for products other than authorized products supplied by Samsung. z ! An electric shock or fire may result. Keep the power socket where the power cord is connected unobstructed. z If any problem occurs in the product, unplug the power cable to completely cut the power to the product.
Before Using the Product Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.). z The product may fall and break or cause a personal injury. z Using the product in an area with excess vibration may damage the product or cause a fire. Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke. z ! An electric shock or fire may result.
Before Using the Product Put down the product carefully. z The product may fall and break or cause a personal injury. ! SAMSUNG ! Installing the product in an unusual place (a place exposed to a lot of fine particles, chemical substances or extreme temperatures, or an airport or train station where the product should operate continuously for an extended period of time) may seriously affect its performance.
Before Using the Product During a lightning or thunderstorm, power off the product and remove the power cable. z ! An electric shock or fire may result. Do not drop objects on the product or apply impact. z An electric shock or fire may result. ! Do not move the product by pulling the power cord or any cable. z Otherwise, the power cable may be damaged and product failure, an electric shock or fire may result. If a gas leakage is found, do not touch the product or power plug.
Before Using the Product 100 Do not insert a metallic object (a chopstick, coin, hair pin, etc.) or inflammable object (paper, match, etc.) into the vent or ports of the product. z If water or any foreign substance enters the product, be sure to power off the product, remove the power cord, and contact Samsung Customer Service Center (81page). z Product failure, an electric shock or fire may result.
Before Using the Product Do not let water enter the DC power device or get the device wet. z An electric shock or fire may result. z Avoid using the product outdoors where it can be exposed to rain or snow. z Be careful not to get the DC power adapter wet when you wash the floor. Do not put the DC power adapter near to any heating apparatus. z Otherwise, a fire may result. Keep the DC power adapter in a well-ventilated area.
Before Using the Product Exercise caution when adjusting the product angle or stand height. ! z Otherwise, children's fingers or hands may become stuck and injured. z Tilting the product excessively may cause it to fall and result in personal injury. Do not place heavy objects on the product. z Product failure or personal injure may result. Correct posture to use the product Use the product in the correct posture as follows: z Straighten your back.
Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS CONNECTING AND USING A SOURCE DEVICE 2 Copyright 3 3 Icons used in this manual Symbols for safety precautions 4 Cleaning 4 5 5 Cleaning Securing the Installation Space Precautions for storage 6 Safety Precautions 6 7 9 Electricity and Safety Installation Operation 13 Correct posture to use the product 18 Checking the Contents 18 19 Removing the Packaging Checking the Components 20 Parts 20 22 Frontal Buttons Reverse Side 23 I
Table Of Contents SCREEN SETUP CONFIGURING TINT 29 Connecting and Using a PC 29 30 31 32 Connecting to a PC Driver Installation Setting Optimum Resolution Changing the Resolution Using a PC 35 Connecting Headphones 36 Connecting the Product to a PC as a USB HUB 36 36 Connecting a PC to the Product Utilizing the Product as a USB HUB 37 Connecting the Power 38 MAGIC 38 39 SAMSUNG MAGIC Bright SAMSUNG MAGIC Color 40 Brightness 40 Configuring Brightness 41 Contrast 41 Configuring Contr
Table Of Contents RESIZING OR RELOCATING THE SCREEN SETUP AND RESET 48 Gamma 48 Configuring Gamma 49 PBP 49 50 Mode Contrast 51 Image Size 51 Changing the Picture Size 52 H-Position & V-Position 52 Configuring H-Position or V-Position 53 ECO 53 55 58 59 Eco Motion Sensor Eco Light Sensor Eco Saving Eco Icon Display 61 Menu Transparency 61 Changing Menu Transparency 62 Language 62 Changing the Language 63 PC/AV Mode 63 Configuring PC/AV Mode 64 Auto Source 64 Configuring
Table Of Contents INFORMATION MENU AND OTHERS TROUBLESHOOTING GUIDE SPECIFICATIONS APPENDIX 68 Off Timer On/Off 68 Configuring Off Timer On/Off 69 Off Timer Setting 69 Configuring Off Timer Setting 70 Reset 70 Initializing Settings (Reset) 71 INFORMATION 71 Displaying INFORMATION 71 Configuring Brightness in the Startup Screen 72 Requirements Before Contacting Samsung Customer Service Center 72 72 72 Testing the Product Checking the Resolution and Frequency Check the followings.
1 1.1 Preparations Checking the Contents 1.1.1 Removing the Packaging 1 Open the packaging box. Be careful not to damage the product when you open the packaging with a sharp instrument. 2 Remove the Styrofoam from the product. 3 Check the components and remove the Styrofoam and plastic bag. 4 z The appearance of actual components may differ from the image shown. z This image is for reference only. Store the box in a dry area so that it can be used when moving the product in the future.
1 Preparations 1.1.2 Checking the Components z Contact the dealer from whom you purchased the product if any item is missing. z The appearance of the components and items sold separately may differ from the image shown. Components Quick Setup Guide Warranty Card User Manual (Not available in all locations) Power cable DC power adapter USB 3.0 cable Dual-link DVI cable DP cable (optionally) Stand base Components may differ in different locations.
1 1.2 Preparations Parts 1.2.1 Frontal Buttons The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Icons Description z Open or close the onscreen display (OSD) menu, or return to the last menu. z OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings. To lock the OSD control, press the MENU button [ ] for five seconds.
1 Preparations Icons Description Configure Customized Key and press [ enabled. z ]. The following options will be ECO - MAGIC - Image Size To configure Customized Key, go to SETUP&RESET Customized Key and select the mode you want. Adjust the screen brightness. Volume can be adjusted if a cable is connected to the [DP IN] or [AUDIO IN] port. Confirm a menu selection. Pressing the [ ] button when the OSD menu is not displayed will change the input source (Digital1/Digital2/DisplayPort).
1 Preparations 1.2.2 Reverse Side The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Port Description Connects to the DC power adapter. Connects to a PC via a DVI cable. Connects to a PC via a DP cable. Connect to a USB device. Compatible with a USB cable version 3.0 or lower. Connects to the stereo cable Connects to an audio output device such as headphones. Connects to a PC via a USB cable.
1 1.3 Preparations Installation 1.3.1 Attaching the Stand Place a protective cloth or cushion on a flat surface. Next, place the product with the face down on top of the cloth or cushion. Insert the stand base into the stand in the direction of the arrow. Do not remove the fixing pin until you are finished attaching the stand. Tightly fasten the screw to the bottom of the base. After installing the stand, place the product upright. You can remove the fixing pin and adjust the stand now.
1 Preparations 1.3.2 Adjusting the Product Tilt and Height The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. z To adjust the height, remove the fixing pin. z The monitor tilt and height can be adjusted. z Hold the top center of the product and adjust the height carefully. 1.3.3 Rotating the Monitor Screen You can rotate your monitor as shown below. z Be sure to fully extend the stand before rotating the monitor.
1 Preparations 1.3.4 Installing a Wall-mount Kit or Desktop Stand Before Installation Power the product off and remove the power cable from the power socket. Place a protective cloth or cushion on a flat surface. Next, place the product with the face down on top of the cloth or cushion. Unfasten the screw from the back of the product. Lift and detach the stand.
1 Preparations Notes z Using a screw longer than the standard length can damage the internal components of the product. z The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications. z Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit or desktop stand using excessive force. The product may get damaged or fall and cause personal injury.
1 1.4 Preparations "MagicRotation Auto" The "MagicRotation Auto" function detects the rotation of monitors that are fitted with a rotation sensor and rotates the Windows screen accordingly. [Software Installation] 1 2 Insert the user manual CD provided with the product into the CD-ROM drive. Follow the instructions given on the screen to proceed with installation. After installation, the on-screen display (OSD) menu will be displayed in the language of the operating system.
2 2.1 Connecting and Using a Source Device Before Connecting 2.1.1 Pre-connection Checkpoints z Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. z Do not connect the power cable until all connections are completed. Connecting the power cable during connection may damage the product. z Check the types of ports at the back of the product you want to connect.
2 2.2 Connecting and Using a Source Device Connecting and Using a PC 2.2.1 Connecting to a PC z Select a connection method suitable for your PC. Connecting parts may differ in different products. Connection using a Dual-link DVI cable (digital type) DVI IN 1 2 Connect the DVI cable to the [DVI IN] port on the back of the product and the DVI port on the PC. Connect the DC power adapter to the product and a power socket, and turn on the power switch on the PC. (For details, refer to "2.
2 Connecting and Using a Source Device If audio is supported, the Volume can be adjusted using the [ ] buttons on the front of the product. 2.2.2 Driver Installation z You can set the optimum resolution and frequency for this product by installing the corresponding drivers for this product. z An installation driver is contained on the CD supplied with the product. z If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com) and download the file.
2 Connecting and Using a Source Device 2.2.3 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language and change the resolution to the optimum value. The optimal resolution for this monitor is as follows: 2560 x 1440 60Hz Follow the above settings to set the resolution.
2 Connecting and Using a Source Device 2.2.4 Changing the Resolution Using a PC z Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. z The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel Display Settings and change the resolution.
2 Connecting and Using a Source Device Changing the Resolution on Windows Vista Go to Control Panel Personalization Display Settings and change the resolution.
2 Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution and change the resolution.
2 2.3 Connecting and Using a Source Device Connecting Headphones AUDIO IN 1 Connect the stereo cable to the [AUDIO IN] port on the back of the product and the AUDIO OUT port on the PC. If the stereo cable is connected, the Volume can be adjusted using the [ ] buttons on the front of the product. 2 Connect an audio output device such as headphones or speakers to [ ] on the product.
2 2.4 Connecting and Using a Source Device Connecting the Product to a PC as a USB HUB 2.4.1 Connecting a PC to the Product The product can function as a HUB by connecting to a PC via a USB cable. You can connect a source device directly to the product and control the device from the product, without having to connect the device to the PC. To use the product as a USB hub, connect the product to a PC using a USB cable. Connect the USB cable to [ ] on the back of the product and USB [ ] on the PC.
2 2.5 Connecting and Using a Source Device Connecting the Power Put the DC power adapter in the groove, with the switch facing upward. - Push the adapter until you hear a “click.” Connect the power cable to the DC power adapter. Next, connect the DC power adapter to the product. Plug in the power cable to the power socket. - Removing the DC power adapter To remove the DC power adapter, lift it outwards from the bottom as shown in the image.
3 3.1 Screen Setup Configure the screen settings such as brightness and color tone. MAGIC This feature optimizes the brightness and colors according to how the product will be used. 3.1.1 SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. z This menu is not available when Eco Light Sensor or Eco Saving is set to On.
3 Screen Setup 3.1.2 SAMSUNG MAGIC Color SAMSUNG MAGICColor is a new picture-quality improvement technology developed independently by Samsung, which delivers vivid natural colors without picture quality degradation. z SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. z This menu is not available when PBP is set to On. SAMSUNG Configuring MAGIC Color 1 2 3 4 Press [ ] on the product.
3 3.2 Screen Setup Brightness Adjust the general brightness of the picture. (Range: 0~100) A higher value will make the picture appear brighter. z SAMSUNG This menu is not available when MAGIC Bright is set to Dynamic Contrast mode. z This menu is not available when Eco Light Sensor or Eco Saving is set to On. 3.2.1 Configuring Brightness 1 2 3 Press [ ] on the product. Press [ ] to move to PICTURE and press [ Press [ ] to move to Brightness and press [ ] on the product. ] on the product.
3 3.3 Screen Setup Contrast Adjust the contrast between the objects and background. (Range: 0~100) A higher value will increase the contrast to make the object appear clearer. z SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 3.3.1 Configuring Contrast 1 2 3 Press [ ] on the product.
3 3.4 Screen Setup Sharpness Make the outline of objects more clear or blurry. (Range: 0~100) A higher value will make the outline of objects clearer. z SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. z This menu is not available when PBP is set to On. 3.4.1 Configuring Sharpness 1 2 3 Press [ ] on the product.
3 3.5 Screen Setup Response Time Accelerate the panel response rate to make video appear more vivid and natural. z It is best to set Response Time to Normal or Faster when you are not viewing a movie. z The functions available on the monitor may vary depending on the model. Refer to the actual product. z This menu is not available when PBP is set to On. 3.5.1 Configuring Response Time 1 2 3 Press [ ] on the product. Press [ ] to move to PICTURE and press [ ] on the product.
4 Configuring Tint SAMSUNG Adjust the tint of the screen. This menu is not available when MAGIC Bright is set to Cinema or Dynamic Contrast mode. Red Adjust the value of the color red in the picture. (Range: 0~100) A higher value will increase the intensity of the color. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. z This menu is not available when PBP is set to On. 4.1.1 Configuring Red 1 2 3 Press [ ] on the product.
4 Green Adjust the value of the color green in the picture. (Range: 0~100) A higher value will increase the intensity of the color. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. z This menu is not available when PBP is set to On. 4.2.1 Configuring Green 1 2 3 Press [ ] on the product. Press [ ] to move to COLOR and press [ Press [ ] to move to Green and press [ ] on the product. ] on the product. The following screen will appear.
4 Blue Adjust the value of the color blue in the picture. (Range: 0~100) A higher value will increase the intensity of the color. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. z This menu is not available when PBP is set to On. 4.3.1 Configuring Blue 1 2 3 Press [ ] on the product. Press [ ] to move to COLOR and press [ Press [ ] to move to Blue and press [ ] on the product. ] on the product. The following screen will appear.
4 Color Tone Adjust the general color tone of the picture. z SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. z This menu is not available when PBP is set to On. 4.4.1 Configuring the Color Tone Settings 1 2 3 Press [ ] on the product. Press [ ] to move to COLOR and press [ Press [ ] to move to Color Tone and press [ ] on the product. ] on the product. The following screen will appear.
4 Gamma Adjust the mid-range brightness (Gamma) of the picture. This menu is not available when PBP is set to On. 4.5.1 Configuring Gamma 1 2 3 Press [ ] on the product. Press [ ] to move to COLOR and press [ ] on the product. Press [ ] to move to Gamma and press [ ] on the product. The following screen will appear. COLOR Red 50 Green 50 Blue Color Tone 1RUPDO Gamma 4.
5 PBP The PBP (Picture by Picture) function separates the screen in half displaying output from two different source devices simultaneously on the left and right sides of the screen. Compatible with Windows 7 only. 5.1.1 Mode 1 2 3 4 Press [ ] on the product. Press [ ] to move to SIZE&POSITION and press [ Press [ ] to move to PBP and press [ Press [ ] to move to Mode and press [ ] on the product. ] on the product. ] on the product. The following screen will appear. PBP 5.
5 Resizing or Relocating the Screen z The PBP function may not be available depending on the specifications of the graphics card used. If the screen is blank in PBP mode when the optimum resolution (1280 x 1440) is selected, go to Control Panel Display Screen Resolution and click Detect on the PC. (Instructions are based on Windows 7.) If the screen is blank when the resolution is set to 1280 x 1440, change the resolution to 1280 x 1024.
5 5.2 Resizing or Relocating the Screen Image Size Change the picture size. This menu is not available when PBP is set to On. 5.2.1 Changing the Picture Size 1 2 3 Press [ ] on the product. Press [ ] to move to SIZE&POSITION and press [ Press [ ] to move to Image Size and press [ ] on the product. ] on the product. The following screen will appear.
5 5.3 Resizing or Relocating the Screen H-Position & V-Position H-Position: Move the screen to the left or right. V-Position: Move the screen up or down. z This menu is only available when Image Size is set to Screen Fit. z This menu is not available when PBP is set to On. 5.3.1 Configuring H-Position or V-Position 1 2 3 Press [ ] on the product. Press [ ] to move to SIZE&POSITION and press [ ] on the product. Press [ ] to move to H-Position or V-Position and press [ ] on the product.
6 6.1 Setup and Reset ECO The Eco Motion Sensor, Eco Light Sensor, and Eco Saving options are displayed on the same menu page so that you can conveniently configure the power saving settings. 6.1.1 Eco Motion Sensor The Eco Motion Sensor activates to save power when it does not detect any movement within a specified area for a specified period of time. Eco Motion Sensor is not available when the monitor is used in portrait mode. Configuring Eco Motion Sensor 1 2 3 4 Press [ ] on the product.
6 Setup and Reset 6 The selected option will be applied. Configuring Backlight 1 2 3 4 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Backlight and press [ ] on the product. ] on the product. ] on the product. The following screen will appear.
6 Setup and Reset 6.1.2 Eco Light Sensor The Eco Light Sensor feature optimizes the view condition and contributes to power saving by adjusting the screen brightness depending on the ambient light intensity. z SAMSUNG This menu is not available when MAGIC Bright is set to Dynamic Contrast mode. z This menu is not available when Eco Saving is set. Configuring Eco Light Sensor 1 2 3 4 Press [ ] on the product.
6 Setup and Reset Configuring Sensitivity 1 2 3 4 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Sensitivity and press [ ] on the product. ] on the product. ] on the product. The following screen will appear.
6 Setup and Reset Configuring Brightness Level 1 2 3 4 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Brightness Level and press [ ] on the product. ] on the product. ] on the product. The following screen will appear.
6 Setup and Reset 6.1.3 Eco Saving The Eco Saving function reduces power consumption by controlling the electric current used by the monitor panel. z SAMSUNG This menu is not available when MAGIC Bright is set to Dynamic Contrast mode. z This menu is not available when Eco Light Sensor is set. Configuring Eco Saving 1 2 3 4 Press [ ] on the product.
6 Setup and Reset 6.1.4 Eco Icon Display Configuring Eco Icon Display 1 2 3 4 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Eco Icon Display and press [ ] on the product. ] on the product. ]. The following screen will appear.
6 Setup and Reset bar level will decrease with a moon image displayed. The brightness slide bar will be displayed for 3 seconds after the sensor activates. You've saved * tree(s). z A pop-up as shown above will appear when an energy tree completes while Eco Icon Display is On. If the above picture is displayed, it means the Eco Icon Display option is On. Change this setting to Off if you do not want to display the pop-up.
6 6.2 Setup and Reset Menu Transparency Set the transparency for the menu windows: 6.2.1 Changing Menu Transparency 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Menu Transparency and press [ ] on the product. ] on the product. The following screen will appear.
6 6.3 Setup and Reset Language Set the menu language. z A change to the language setting will only be applied to the onscreen menu display. z It will not be applied to other functions on your PC. 6.3.1 Changing the Language 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Language and press [ ] on the product. ] on the product. The following screen will appear.
6 6.4 Setup and Reset PC/AV Mode Set PC/AV Mode to AV. The picture size will be enlarged. This option is useful when you view a movie. This menu is not available when PBP is set to On. 6.4.1 Configuring PC/AV Mode 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to PC/AV Mode and press [ ] on the product. ] on the product. The following screen will appear.
6 6.5 Setup and Reset Auto Source Activate Auto Source. This menu is not available when PBP is set to On. 6.5.1 Configuring Auto Source 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Auto Source and press [ ] on the product. ] on the product. The following screen will appear.
6 6.6 Setup and Reset Display Time Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified period of time. Display Time can be used to specify the time after which you want the OSD menu to disappear. 6.6.1 Configuring Display Time 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Display Time and press [ ] on the product. ] on the product. The following screen will appear.
6 6.7 Setup and Reset Key Repeat Time Control the response rate of a button when the button is pressed. 6.7.1 Configuring Key Repeat Time 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Key Repeat Time and press [ ] on the product. ] on the product. The following screen will appear.
6 6.8 Setup and Reset Customized Key You can set Customized Key to the mode you want as follows. This menu is not available when PBP is set to On. 6.8.1 Configuring Customized Key 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Customized Key and press [ ] on the product. ] on the product. The following screen will appear.
6 6.9 Setup and Reset Off Timer On/Off Enable or disable the off timer that automatically powers off the product. 6.9.1 Configuring Off Timer On/Off 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Off Timer On/Off and press [ ] on the product. ] on the product. The following screen will appear.
6 Setup and Reset 6.10 Off Timer Setting The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number of hours. This menu is only available when Off Timer On/Off is set to On. 6.10.1 Configuring Off Timer Setting 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Off Timer Setting and press [ ] on the product. ] on the product. The following screen will appear.
6 Setup and Reset 6.11 Reset Return all the settings for the product to the default factory settings. This menu is not available when PBP is set to On. 6.11.1 Initializing Settings (Reset) 1 2 3 Press [ ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Reset and press [ ] on the product. ] on the product. The following screen will appear.
7 7.1 INFORMATION Menu and Others INFORMATION View the current input source, frequency and resolution. 7.1.1 Displaying INFORMATION 1 2 Press [ Press [ ] on the product. ] to move to INFORMATION. The current input source, frequency and resolution will appear. PICTURE COLOR 'LJLWDO SIZE&POSITION N+] +] 11 [ SETUP&RESET INFORMATION Move Exit 7.
8 8.1 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center 8.1.1 Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check if your product is operating normally by using the product test function. If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC, perform a self-diagnosis test.
8 Troubleshooting Guide Screen issue Not Optimum Mode is displayed. This message appears if the signal from the graphics card exceeds the maximum resolution or frequency for the product. Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (79page). The images on the screen look distorted. Check the cable connection to the product (Refer to "2.2 Connecting and Using a PC") The screen is not clear. The screen is blurry.
8 Troubleshooting Guide Source device issue A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is booting, have your PC serviced.
8 8.2 Troubleshooting Guide Q&A Question How can I change the frequency? Answer Set the frequency on your graphics card. z Windows XP: Select Control Panel Themes Display Settings Appearance and Advanced Monitor, and adjust Refresh rate under Monitor settings. z Windows ME/2000: Select Control Panel Settings Advanced Display Monitor, and adjust Refresh rate under Monitor settings.
8 Troubleshooting Guide Question How can I change the resolution? Answer z Windows XP: Go to Control Panel Display z Appearance and Themes Settings and adjust the resolution. Windows ME/2000: Go to Control Panel Display Settings and adjust the resolution. z Windows Vista: Go to Control Panel Personalization Personalize Appearance and Display Settings and adjust the resolution.
9 9.1 Specifications General Model Name Panel Synchronization Size 27 inches (68 cm) Display area 596.74mm(H) x 335.66mm(V) Horizontal Frequency 31~90 kHz Vertical Frequency 56~76 Hz Display Color Resolution S27A850D 16.7 M (True 8 bit) Optimum resolution 2560 x 1440 @ 60 Hz Maximum resolution 2560 x 1440 @ 60 Hz Maximum Pixel Clock 270 MHz (DVI-D, DP) Power Supply This product uses 100 to 240V.
9 Specifications This Class B device designed for home use is registered for EMC requirements and can be used in all regions. (USA Only) Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278 - 0799 9.
9 9.3 Specifications Standard Signal Mode Table This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Therefore, a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for the screen size of your product.
9 Specifications Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA,1600 x 1200 75.000 60.000 162.000 +/+ VESA,1680 x 1050 65.290 59.954 146.250 -/+ VESA,1920 x 1200 74.556 59.885 193.250 -/+ VESA, 2560 x 1440(RB) 88.787 59.951 241.500 +/- z Horizontal Frequency The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle.
Appendix Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca http://www.samsung.com/ch_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com LATIN AMERICA ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 4004-0000 http://www.samsung.
Appendix EUROPE ALBANIA 42 27 5755 http://www.samsung.com AUSTRIA 0810 - SAMSUNG (7267864, € 0.07/min) http://www.samsung.com BELGIUM 02-201-24-18 http://www.samsung.com/be (Dutch) http://www.samsung.com/be_fr (French) BOSNIA 05 133 1999 http://www.samsung.com BULGARIA 07001 33 11 http://www.samsung.com CROATIA 062 SAMSUNG (062 726 7864) http://www.samsung.com CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com Samsung Zrt.
Appendix EUROPE PORTUGAL 808 20 - SAMSUNG (808 20 http://www.samsung.com 7267) RUMANIA From landline : 08010-SAMSUNG http://www.samsung.com (7267864) From landline & mobile : (+40) 21 206 01 10 SERBIA 0700 Samsung (0700 726 7864) http://www.samsung.com SLOVAKIA 0800 - SAMSUNG http://www.samsung.com (0800-726 786) SPAIN 902 - 1 - SAMSUNG (902 172 678) http://www.samsung.com SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com SWITZERLAND 0848-SAMSUNG (7267864, CHF 0.08/min) http://www.
Appendix CIS UKRAINE 0-800-502-000 http://www.samsung.com/ua http://www.samsung.com/ ua_ru BELARUS 810-800-500-55-500 http://www.samsung.com MOLDOVA 00-800-500-55-500 http://www.samsung.com ASIA PACIFIC AUSTRALIA 1300 362 603 http://www.samsung.com NEW ZEALAND 0800 SAMSUNG (0800 726 786) http://www.samsung.com CHINA 400-810-5858 http://www.samsung.com HONG KONG (852) 3698 - 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 1800 1100 11 http://www.samsung.
Appendix MIDDlE EAST IRAN 021-8255 http://www.samsung.com OMAN 800-SAMSUNG (726-7864) http://www.samsung.com KUWAIT 183-2255 http://www.samsung.com BAHRAIN 8000-4726 http://www.samsung.com EGYPT 08000-726786 http://www.samsung.com JORDAN 800-22273 http://www.samsung.com MOROCCO 080 100 2255 http://www.samsung.com SAUDI ARABIA 9200-21230 http://www.samsung.com U.A.E 800-SAMSUNG (726-7864) http://www.samsung.com AFRICA CAMEROON 7095- 0077 http://www.samsung.
Appendix Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
Appendix Terminology OSD(On Screen Display) On screen display (OSD) allows you to configure on-screen settings to optimize the picture quality as required. It allows you to change the screen brightness, tint, size and many other settings using menus displayed on the screen. HUB HUB refers to a device that is a common connection point for multiple devices connected over a network. It is used to connect multiple PCs, video devices, office devices and/or LANs over a single network.
Appendix Vertical Frequency One image is made of numerous horizontal lines. The vertical frequency is measured in Hz and represents how many images can be created per second by those horizontal lines. A vertical frequency of 60 means that an image is transmitted 60 times per second. The vertical frequency is also called "refresh rate" and affects screen flicker. Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen. It represents the level of display detail.
Index A INFORMATION 71 Auto Source 64 Installing the Product 23 B K Before Connecting 28 Key Repeat Time 66 Blue 46 Brightness 40 L Languagey 62 C Checking the Contents 18 Cleaning 4 Color Tone 47 M MAGIC 38 Menu Transparency 61 Configuring Brightness in the Startup Screen 71 Connecting and Using a PC 29 O Connecting Headphones 35 Off Timer On/Off 68 Contrast 41 Off Timer Setting 69 Copyright 2 Correct Disposal of This Product 86 Correct posture to use the product 13 Customized Key 67 P
Index S Safety Precautions 6 Sharpness 42 Standard Signal Mode Table 79 T Terminology 87 U Utilizing the Product as a USB HUB 36 Index 90
