SyncMaster 757MB/957MB
Main Page On-Screen Display General Highlight Zone Highlight Zone II MouScreen™ Safety Instructions Troubleshooting Notational Check List Power Q&A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Unpacking General Specifications Front Preset Timing Modes Rear PowerSaver Bottom Setup Information Connecting Your Monitor Service Installing the Monitor Driver Terms Automatic Regulatory Manual Natural Color Base Installation MouScreen™ Authority
Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. z Notational Power If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Installation Clean Other Do not use a damaged or loose plug. z This may cause an electric shock or fire.
Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Notational Power Installation Clean Other Put your monitor in a location with low humidity and a minimum of dust. z An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or human body. Place the monitor on a flat and stable surface. z The monitor can cause injury by falling. Set down the monitor carefully.
Notational Power Installation Clean Other When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using.
Do not remove cover(or back). No user serviceable parts inside. z z Notational This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. z This may cause an electric shock or a fire. Do not place any heavy objects on the monitor.
Keep the monitor away from any magnetic substances. z This may cause discoloring or distortion of the image.
Monitor and Stand Power Cord Unpacking Stand Front Rear Bottom Signal Cable (Option) (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Unpacking Front Rear Bottom 1. Highlight button 2. Exit/MagicBright button The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. Use this button to exit or conrtol the MagicBright. 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5.
1. Attaching Monitor | 2. Detaching Monitor(Option) Unpacking 1. Attaching Monitor Front Rear Bottom (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal Cable Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 2.
3 3. BNC Connectors (Option) Connect the signal cable to the BNC signal port on the back of your monitor. 4. USB Connector (Option) Connect the USB cable to the USB port on the back of your monitor. Note: See Connecting Your Monitor for further information regarding cable connections.
Unpacking Front Rear Bottom 1. Signal Cable 2. Power port 3. Tilt/Swivel Base Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Connect the power cord for your monitor to the power port on the back of the monitor. You can separate the base from the monitor.
1. Attaching Monitor | 2. Detaching Monitor(Option) Connecting Your Monitor 1. Attaching Monitor Installing the Monitor Driver Base Installation 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3.
1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin D-sub connector on the back of your monitor. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included).
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Connecting Your Monitor Installing the Monitor Driver Base Installation Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.
4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
Connecting Your Monitor When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Installing the Monitor Driver Base Installation Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test.
Tilt/Swivel Base | Attaching and Removing the Base Connecting Your Monitor Installing the Monitor Driver With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. Base Installation Note: The base is detachable. Attaching the Base 1. 2. 3. 4. Place the monitor upside-down on a flat work surface. Align the tabs on the base with the corresponding slots on the bottom of the monitor.
position. ii * Do not bend the snap. Removing the Base 5. Squeeze and pull up on the release latch on the base. 6. Push the base toward the back of the monitor and lift up to remove the base. Note: The base will align with the monitor slots in only one position.
On-Screen Display 1. Highlight button : The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. 2. Exit/MagicBright button : Use this button to exit or to activate the MagicBright menu. 3. Adjust buttons : These buttons allow you to highlight and adjust items in the menu. 4. Menu button : Use this button to open the OSD and activate a highlighted menu item.
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Check List Q&A Self-Test Feature Check Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection. Have the screen colors become strange after running a program or due to a crash between applications? Reboot the computer. Has the video card been set properly? Set the video card by referring to the video card manual.
( g ) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Tips for Highlight Zone 1. To protect CDT against the screen brightness, the Highlight Zone function persists for three hours and then automatically stops. So please reset it to continue. 2.
1. General Q & A | 2. Highlight Zone II Q & A | 3. MouScreen Q & A 1. General Q & A Check List Q&A Self-Test Feature Check Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows ME/2000/XP: Set the resolution at the Control Panel, Display, Settings.
i "USB N t d" ( )C it saying, Nott C Connected" )Connectt th the monitor properly before using it. Neither Automatic Detect or nor Manual Detect function while the icon shows the message, "USB Not Connected". You can only exit the program. Started a multimedia program but the Highlight Zone function does not automatically activate. Check the Highlight Zone II menu and see if Disable Auto Detect is selected. When selected, the Highlight Zone function is not automatically activated.
p connected to a root port or a hub USB port connected to the computer. If not connected properly, the MouScreen program will not run, displaying the following message: If you see the above message even when the monitor port is correctly connected to the computer, this means the operating system does not recognize the USB monitor. In this case, disconnect and then reconnect the USB port/cable before running the program. The operating system should now recognize the USB monitor.
Self-Test Feature Check | Warning Messages | Environment | Useful Tips Check List Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Q&A Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If your monitor works normally, the following screen appears. Failure of any of the boxes to appear indicates a problem with your monitor.
1 If there are any woofer speakers near the monitor, monitor unplug and relocate the woofer to another 1. room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. 3. Degauss the monitor if any devices were removed from the area. z z A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Sync.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 757MB Picture Tube Type 17"(43cm) MagicBright™ (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes PowerSaver Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 957MB Picture Tube Type 19"(48cm) MagicBright™ (45.8cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes PowerSaver Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM. 640 x 480 31.469 59.940 25.175 -/- IBM.
Service Terms Regulatory Natural Color MouScreen™ Authority U.S.A. : Samsung Computer Products Customer Service 400 Valley Road, Suite 201, Mt. Arlington, NJ 07856 Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864) Fax. : (973)601-6001 http://samsungusa.com/monitor/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc.
Samsung Electronics S.A. S El t i Comercial C i l Iberica, Ib i SA Ciencies, 55-65 (Poligono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 261 67 00 Fax. : (93) 261 67 50 http://samsung.es/ United Kingdom : Samsung Electronics (UK) Ltd. Samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0208) 391 0168 Fax. : (0208) 397 9949 < European Service Center & National Service > Stafford Park 12 Telford, Shropshire, TF3 3BJ Tel. : (0870) 242 0303 Fax.
http://www samsung pt/ http://www.samsung.pt/ NETHERLANDS/BELGIUM/LUXEMBOURG : Samsung Electronics Benelux B. V. Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS Service and informatielijn ; Belgium :0800-95214, http://www.samsung.be/ Netherlands : 0800-2295214, http://www.samsung.nl/ CHILE : SONDA S.A. Teatinos 550, Santiago Centro, Santiago, Chile Fono: 56-2-5605000 Fax: 56-2-5605353 56-2-800200211 http://www.sonda.com/ http://www.samsung.cl/ MEXICO : Samsung Electronics Mexico S.A. de C.V. Saturno 44 Col.
Dot Pitch Service The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Terms Vertical Frequency Regulatory The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
Service Terms Regulatory Natural Color MouScreen™ Authority FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice (Europe only) Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
What does labelling involve? This product meets the requirements for the TCO'95 scheme, which provides for international environmental labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and Technical Development in Sweden).
TCO'95 The relevant TCO 95 requirement: Neither CFCs nor HCFCs may be used during the manufacturing of the product or its packaging. z TCO'99-Ecological requirements for personal computers (TCO applied model only) Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use.
eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available.
Natural Color Software Program Service Terms Regulatory Natural Color MouScreen™ Authority One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem.
MouScreen™ S/W Service Terms Regulatory Natural Color MouScreen™ Authority MouScreen Program requires built-in USB for use with SyncMaster Products. (Note: SyncMaster 1200NF does not support MouScreen.) MouScreen is a software program that controls your monitor settings using the USB (Universal Serial Bus) interface. All monitor settings, adjustments and controls can be managed by the use of the mouse alone.
Information in this document is subject to change without notice. © 2002 Samsung Electronics Co., Ltd. All rights reserved. Service Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Terms Regulatory Natural Color MouScreen™ Authority Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
