! ! ! SyncMaster 711ND Install drivers Install programs !
Notation Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause an electric shock or fire.
Installation Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and chemical substances, or where it will be operated for 24 hours continuously such as an airport, train station or etc. Failure to do so may cause serious damage to your set. Put your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause an electric shock or fire inside the monitor.
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in internal temperature may cause fire. Set down the monitor carefully. The monitor could be damaged or broken. Do not place the monitor face down. The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector may cause an electric shock or fire. Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.
This may cause an electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause malfunction, an electric shock or fire. Especially avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center. The monitor may malfunction, causing an electric shock or fire.
This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury. Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports. It may cause a fire or an electric shock. If an alien substances or water flows into the product, turn the product off, unplug the power connector from the wall outlet and contact Service Center.
Failure to disconnect a cable may damage it and lead to fire or an electric shock. Place the product out of children's reach, as they could damage it by hanging onto it. A falling product could cause physical damage even death. When not using the product for an extended time period, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
Features What is a network monitor? This is a new concept monitor that accesses the PC and LAN services to display images, video clips, documents, etc. by connecting to the host PC. It also has an additional function that remotely connects to the host PC for Internet services, independently of the host PC. MagicNet, which is provided with the product, remotely accesses the network to adjust the time and type of the display contents on each network monitor as well as switching the power on/off remotely.
Package Contents Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Keyboard (USB) Mouse (USB) Your Monitor Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™ button [ ] MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available : Custom, Text, Internet, Game, Sport and Movie. Each mode has its own preconfigured brightness value.
5) Sport For watching motion pictures such as a sport. 6) Movie For watching motion pictures such as a DVD or Video CD. >> Click here to see an animation clip Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Adjust buttons [ Adjust items in the menu. ] Enter button [ ] / SOURCE button Activates a highlighted menu item. / Push the 'SOURCE', then selects the video signal while the OSD is off.
Cable Fix Ring When connecting the cable is finished, fix the cables to the Cable Fix Ring. USB (USB Connection Terminal) Connect USB devices such as a mouse, keyboard and external storage devices (e.g. DSC, MP3, external storage, etc.). LAN (LAN Connection Terminal) Connect when using it as a monitor. See Connecting Cables for further information regarding cable connections.
Up-Down Left-Right buttons ENTER AUTO LOCK MagicNet Remote Control ON / OFF Use these buttons to turn the monitor on or off. NUM, ENG Used to enter numbers or text in English. SYMBOL : Used to enter symbols. DEL Functions as the backspace. ENTER Activates a highlighted menu item. BRIGHT buttons When OSD is not on the screen, push the button to adjust brightness. PAGE Selection Used to select a page. MagicNet MagicNet Quick Launch Button. PC A shortcut button for analog mode.
Connecting Cables Connect to the host PC using a LAN cable Host PC Hub LAN Cable Monitor Connect the power cord to the power terminal at the back of the monitor. Connect the mouse and the keyboard to the USB ports. Connect the LAN port on the back of the monitor and the hub. Connect the hub and the LAN port of the host PC. The host PC must have an IP address. After connecting the LAN and setting the IP address, you can view the host PC screen on the monitor.
Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analog) connector on the video card. - Connect the D-Sub Cable to the VGA IN port on the back of your monitor. [VGA IN] To use the D-Sub (analog) output through another device (monitor, TV, projector, etc.) - Connect the VGA OUT port of the monitor and the D-Sub port of another device using the D-Sub cable.
USB (USB Connection Terminal) Connect USB devices such as a mouse, keyboard and external storage devices (e.g. DSC, MP3, external storage, etc.). (You cannot use these devices without connecting to the host PC or switching to the MagicNet.) LAN (LAN Connection Terminal) Connect the LAN cable. D-sub 15-pin port [VGA OUT] Use it by connecting it to another monitor. (The picture of the main monitor is displayed on the connected monitor.
It can execute a file(s) registered with the host PC. And it can also locate and run any external devices connected to other network monitors. When using MagicNet with MagicNet Server Program : execute Network mode. Photo JPEG, BMP file format is supported. Movie AVI, MPEG1/2, DivX 4.x, DivX 5.x file format is supported. OFFICE/HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. RDP Allows you to connect to the host PC.
Right-click it and select 'New User'. Enter the user name, password and properties and select 'Create'. A new account is now created.
Right-click the new account and select 'Properties'. Select 'Add'. Select 'Advanced'.
Select the 'Find Now' button. Select 'Remote Desktop User'.
Click 'OK'. The new group is displayed in the 'Remote Desktop Users' list.
Select one of the old group and click 'Delete'. Click 'Apply' and then 'OK'. A new account is now created.
Other Useful Functions You can share a program installed on the host PC with other users. Before Using The host PC should be installed using Windows 2000/ 2003 Server. Windows XP Home/Professional does not support multiple access by two users at the same time. If the installed OS does not recognize the mouse, disconnect it and then reconnect it. MagicNet supports the FAT format and does not support other formats including NTFS.
The default monitor password is “000000". Using the Stand Pivot Stand Stand Stopper You can only rotate the screen when the screen is lifted to its maximum height. Do not rotate the screen by force, as this might damage the stand. Using the Stand Using Other Stands Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Monitor Mounting interface pad ( Sold separately ) Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove four screws and then remove the stand from the LCD monitor. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
MagicNet ( Host PC ) MagicNet Installation | MagicNet Help MagicNet Installation Insert the installation CD into the CD-ROM drive. Click the MagicNet installation file. Select installation Language, Click "Next". When the InstallShield Wizard window appears, click "Next." Select "I agree to the terms of the license agreement" to accept the terms of use.
You are required to log in to the MagicNet Server program. Please enter the password to login. The password cannot be changed when you are logged in. Select SyncMaster 711ND. When selecting an Combination, install it only in the integration format of the 400Pn/460Pn and 711ND models. When selecting a single model, some functions may not work so make sure to install the appropriate programs.
Choose a folder to install the MagicNet program. Click "Install." The "Installation Status" window appears.
It is recommended restarting the system for the normal operation of the MagicNet Server program. Click "Finish." When the installation is complete, the MagicNet executable icon appears on your desktop.
MagicNet transmits media files (photo and movie files) and office files (PowerPoint, Excel, Word, HTML and PDF files) existing on a server to monitors using the Ethernet network of the server/client architecture. Several monitors can be connected to a server, and any file can be transmitted to any monitor over the network.
3. Update You can update a monitor's MagicNet from the server. However, this function only works when it is connected to a server/monitor with MagicNet2 or higher. 4. Controlling Local Storage Devices/USB File Control of Monitors You can copy or Deletes to a monitor's local storage device or via USB connected to the monitor.
Date Monitors connected via the Network Fields Window Registering to the Library Registering to the Library The library consists of a collection of files which can be played from a monitor connected to the MagicNet program. The monitor can only play files with the supported formats registered in the library. The library only accepts files of the supported formats. z z z z Press the "Reg. Library" button to select files that can be registered to the library.
Network The status bar next to the monitor name will display the overall network status (traffic) of all the monitors connected to the server. For example, assume that the network system capability is 100Mbs and a 100Mbs network card is installed in the server. If there is no network traffic used for other purposes, three monitors are connected, and each monitor uses 10Mbs of traffic, the progression will be indicated as about 30%.
Displays the next file. z z Stop z Full Screen When the files are selected in the library list : Stops the slide show. When monitoring information is being played from a schedule : Stops the slide show. When monitoring the information which the monitor user is selecting and playing : This function is disabled. Enlarges/shrinks an image file to fit to the full screen. Double-click the screen to return to the original image size.
1. When selecting a file from among the files already registered, or selecting a random file from the schedule registration window, the file is selected as a schedule file through the library registration procedures. 2. When selecting an image file for the schedule file, you can add background music from among the following music files. If a schedule file is not an image file, the add/delete button for the background music is not activated.
Date Displays the registered schedules in the Fields window ( ) whose date are later than today ( ). Monitors Connected via the Network Lists the names of monitors registered via the network. When a monitor is connected to the network, its background color changes to yellow-green. z Reconnect to the other server automatically 1.
In addition, you can change the name of the monitors. The server program's Power-On option works only if the monitor's power is completely shut off. Please make sure not to use the Power-On option when the monitor is in the process of shutting up since it can possibly cause systemetic error on the monitor. 2. Select Monitor : The schedules of the relevant monitor is queued. z Rename Type a new name and click confirm. The new name will be saved. Fields Window Displays the status of a file.
In this case, when running menus that cannot be adjusted in the output source, the warning 'Adjustment unavailable' will appear. Furthermore, when running adjustable menus, the selected values will be applied to the monitor, and the results will be applied to the MDC status window. If not applied to the monitor, it will also not be applied to the MDC status window. The MDC functions comply with the specifications for running the monitor.
Volume : When changing the volume, the changed details will appear in an OSD on the monitor screen. z 0 ~ 100 Source In the source tab, the output source of the monitor can be changed. When selecting the following output source, it will change to the relevant output source. When the relevant device is not connected, a screen with 'Connection required' will appear.
sources. z z 16 : 9 4:3 2. Color In TV/AV sources from the PC Adjusts the contrast, brightness and R,G,B. z z z z z Contrast Brightness Red Green Blue Time 1. Current Time Establishes the standard time of the monitor. In Hour, Minute and AM/PM, select the time, and click the Apply button. The current standard time of the monitor will be set. To activate the On/Off Timer at the set time, the Current Time must be set. z z z Hour Minute AM/PM 2.
z z z z z Large Small Double1 Double2 Double3 2. Source When selecting sources to be output to PIP, the relevant source will be applied to PIP. When trying to change a source where PIP cannot be applied or the combination of Main/Sub is incompatible, a warning message will appear on the monitor. z z z z z z PC BNC DVI AV S-Video Component Setting 1. Audio Adjust the Bass, Treble and Balance, and set Main/Sub for the Sound Select of Dolby Virtual ON/OFF, BBE ON/OFF and PIP.
z Manual 2. Scroll This function prevents the screen status changing when the same screen is maintained continuously. If you select the Period and Time and press the Apply button, the screen will scroll downwards at the speed of the previously set time in Period. For example, for Period 1, Time 5, the screen will be renewed every hour at a speed of 5 seconds. z z Period Time 3. Video Wall This offers a function that enables you to use several monitors as one screen.
Power Select Power ON/OFF. z z ON OFF Source Select an external source to adjust. z z PC MagicNet Image Adjusts the color density, MagicBright and Reset. z z z Color MagicBright Reset Setting Adjusts the settings for the picture quality, position and auto adjustment.
Message When entering a message to the server and setting the options needed before sending it, the message is displayed on the selected client monitor. z Display Option : - Displays a sentence one line at a time. z z z z z z Start : Displays a message on the selected monitor. Stop : Stops displaying a message on the selected monitor. Clear : Allows you to change the text in the message edit box. Display Period : Marked in Hour and Minute.
Login / Logout Before using MagicNet, you first need to login. After a successful login, the Login button changes to a Logout button. A successful login is required to use the majority of functions. When installing MagicNet for the first time, the administrator account is provided on the basis of the password entered by the user. When adding an account, you can select from among three account types, and the selected account type decides the scope of using MagicNet.
When adding an account, select from among three account types, and the selected account type decides the scope of using MagicNet. You may modify or delete the accounts of existing users as well as adding new users. Account Type Administrator z z z Scope You have the authority to use all functions of MagicNet. Power User You are not authorized to use the Options menu and the Update function from among the MagicNet functions.
If the monitor to the server is changed to SyncMaster 400Pn/460Pn or an integral model (mixed type), the server will be adjusted according to the model. Note that the supportable file formats, MDC and message-related functions will vary depending on the selected monitor model. z z z SyncMaster 400Pn/460Pn SyncMaster 711ND Combination Help 1. Help Runs program help. 2. About MagicNet Indicates the program version and the copyright details.
z When you see no menu in a zoomed-in picture Move up to the top of the image Move down to the bottom of the image Move to the left of the image Move to the right of the image MUSIC (Applicable only to SyncMaster 400Pn/460Pn) Supported File Formats Music File : MP3 Remote Control z When the files are selected in the library list.
Supported File Formats Video File : MPEG1/2, DivX 4.x/5.x (SyncMaster 400Pn/460Pn) Video File : MPEG1/2/4, DivX 4.x/5.
Move to the next page Move to the previous page Exit PDF z Excel Move to the upper cell Move to the lower cell Move to the left cell Move to the right cell Move to the previous page Move to the next page Move to the right sheet Move to the left sheet Exit Excel z Power point Normal Move to the top Move to the previous page Move to the previous page Move to the next page Slideshow Exit Power point z Power point Slideshow Stop slideshow Move to the top Move to the bottom Move to the previous page Move
Exit Power point z Word Move to the top Move to the bottom Move to the previous page Move to the next page Exit Word z HTML Move to the top Move to the bottom Move to the previous page Move to the next page Exit HTML z Internet Move the mouse cursor up Move the mouse cursor down Move the mouse cursor to the left Move the mouse cursor to the right Click when the cursor is placed over a link (move to the link) Exit the Internet Introduction to Schedule MDC Upper | | | | MagicNet OSD Adjustment Menu
To remove MagicNet, complete the following steps. 1. Select [Start] → [Settings] → [Control Panel]. 2. For Windows XP, select [Start] → [Control Panel]. 3. Double-click the [Add or Remove Programs] icon in the Control Panel. 4. Click the MagicNet in the [Add or Remove Programs] window to highlight it. 5. Click [Change/Remove] to remove it. 6. Click OK to start removal of MagicNet. 7. Wait until the window appears which indicates that program removal is completed.
Introduction to Schedule MDC Upper | | | | MagicNet OSD Adjustment Menu Remote Removing Control | |Troubleshooting|Specifications Program Adjustment Specifications Supported File Format Spec (SyncMaster 400Pn/460Pn) Audio Bitrate File Format Resolution VBR Sampling rate Peak bitate - 9Mbps or less - CBR MPEG1 Video MPEG2 (PS) 720x480 or less 9Mbps or less MP3 - Available JPEG 3500 x 2625 or less - - - - - - DivX 4.x DivX 5.
For a LAN-connected environment, the connectable number of devices may be reduced depending on the availability of neighboring networks. Server System Configuration CPU RAM Minimum P1.8 256 M Recommended P3.0 Ghz Ethernet OS Application 100 M Windows XP Windows 2000 (Service Pack 4) WMP 9 or later 512 M Local Device (USB) Connection Speed For a mass storage device such as a USB hard disk, it takes approximately 3 - 4 seconds for loading 1 GB.
Click the "Install" button in the "Warning" window. Monitor driver installation is completed. Windows XP/2000 Insert CD into the CD-ROM drive. Click "Windows XP/2000 Driver". Choose your monitor model in the model list, then click the "OK" button. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo, and this installation don't damage your system.
Windows XP | Windows 2000 | Windows ME | Windows NT | Linux Microsoft® Windows® XP Operating System Insert CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. Select "Don't search ,I will...
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo, and this installation don't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click the "Close" button then click "OK" button continually.
Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install Click "Start" , "Setting" , "Control Panel". Double click the "Display" icon. Select the "Settings" tab and click "Advanced Properties" button.
Click "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
How to delete the Natural Color software program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select Natural Color from the list and then click the "Add/Delete" button. Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Overview What is MagicTune™? Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors.
2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the InstallationShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use. 6. Choose a folder to install the MagicTune™ program.
7. Click "Install." 8. The "Installation Status" window appears. 9. Click "Finish.
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop. Double-click the icon to start the program. MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installation Problems The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation.
MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z z OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Pivot is functioning, part of MagicTune™ Program may not operate normally. AutoRotation : AutoRotation will automatically pivots the monitor to 0, 90, 180degrees when you pivots the monitor.
3. 4. 5. 6. MagicBright™ Game : For watching motion pictures such as a Game. Sport : For watching motion pictures such as a Sport. Movie: For watching motion pictures such as a DVD or Video CD. Custom: Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu. MagicBright control mode will be different according to monitor models.
automatically get the play screen highlighted (it will be supported in players of Gom, Adrenalin, KCP, Window Media, and Power DVD etc., )Some other players also can be highlighted but could have some problems. { Tusk menu Adjust the tint of the color. HUE Saturation Adjusts the color saturation. MagicColor Brightness Adjusts the Brightness. Sharpness Adjusts the difference between the lightest and darkest areas of the display. Zone Off Turn off the zone that you have captured.
z Image Setup z Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. Position Adjusts the screen location horizontally and vertically. Sharpness Changes the clearance of image.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Color Calibration Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . 1. Control "Brightness control bar" for matching the brightness of control patch and the brightness of background pattern 2.
Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows™ Control Panel. Perform the following steps remove MagicTune™. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to highlight it. 4.
An error occurs when the video card driver is not installed properly. This happens when the current video card list is not displayed normally. You can check this via Start → Setup → System → Hardware → Device Manager → Display adaptor. Visit the video card maker's homepage and download and install the latest driver. For more information about the video card, contact the card manufacturer. To ensure normal operation, please restart your system.
MagicTune™ doesn't work properly. z z Have you changed your PC or video graphic card? Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magicTune Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades. Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
* WindowsT is registered trademark of Microsoft Corporation,Inc. Overview | Installation | Interface | Uninstall | Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. 3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Installation Status" window appears.
9. Click "Finish." Have to reboot the system in order for the MagicRotation to work properly. 10. When the installation is complete, the MagicRotation executable icon appears on your desktop. Installation Problems The installation of MagicRotation can be affected by the factors such as video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation. Limitation 1. The "Display Driver" should be properly loaded for the MagicRotation to work properly.
2. If some applications like Windows™ Media Player, Real Player, etc. are not displaying movie files properly in 90, 180 and 270 orientations then do the following : { Close the application. { Select the Orientation (90, 180, 270) you want to view the application. { Relaunch the application. In most cases this should fix the problem. 3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the orientation mode selected (90, 180, 270). e.g. 3D games 4.
The Menu on task bar Menu pop up at the mouse right button click. Rotate : Display will get rotated by the unit of 90 degree Rotate to 0 : Display will get rotated to 0 degree from the current angle of rotation. Rotate to 90 : Display will get rotated to 90 degree from the current angle of rotation.
Rotate to 180 : Display will get rotated to 180 degree from the current angle of rotation. Rotate to 270 : Display will get rotated to 270 degree from the current angle of rotation.
Hot key : Hot Keys are available by default and can be changed by user. It can be assigned by user directly with keyboard after changing the existing HotKey. User can create the hot key with the combination of Shift, Ctrl, Alt and general keys. In case only general key is pressed, it will be assigned in the form of Alt+general key. Help : It shows the HELP of MagicRotation program. About : It shows the version and copyright of MagicRotation program. Exit : It exits from MagicRotation program.
7. After uninstall restart the system to complete the uninstallation. Visit the MagicRotation website for technical support for MagicRotation, FAQs (questions and answers) and software upgrades. * Windows™ is registered trademark of Microsoft Corporation,Inc.
MagicNet In the OSD image of MagicNet, Network mode is the same as Device. Menu Description Network When using MagicNet with MagicNet Server Program : execute Network mode. Device When using MagicNet with the device directly connected to monitor : execute Device mode. Internet Connects to the Internet. You can set various functions in MagicNet mode. You must enter the password to access Setup mode. Play/Stop Schedule View The preset password on the monitor is "000000".
numeric format TCP/IP Schedule View Remote Desktop TCP/IP Setup Displays a schedule. Allows you to adjust the connection settings of the host PC. You can change the TCP/IP settings. DHCP, STATIC Homepage You can change the Internet primary address. Network Setup You can modify the network settings. Change You can change the password. Password Administrator (Setup), User (Network-Photo, Movie, Office/HTML) Menu Description JPEG, BMP file format is supported.
Control Buttons [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. [ ] These buttons allow you to adjust items in the menu. [ ] Press this button to activate a highlighted menu item. [AUTO] When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. The values of fine, coarse and position are adjusted automatically. To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. AUTO Available in analog Mode Only If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy.
Menu Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). OSD Lock & Unlock You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu MagicBright™ Description Push the MagicBright™ button to circle through available preconfigured modes.
Brightness Menu Brightness Description When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu SOURCE Description Selects the Video signal while the OSD is off.
OSD Function Picture Brightness Contrast Color MagicColor Color Tone Color Control Gamma Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Image Reset Color Reset Information Picture Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. Off Demo Returns to the original mode. The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. Full Displays not only vivid natural color but also more realistic natural skin color with clearness.
Color Tone The tone of the color can be changed and one of four modes can be selected -Cool, Normal, Warm and Custom. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → Color Control , → → , → , → → MENU Adjusts individual Red, Green, Blue color balance. - Red, Green, Blue ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → , → → → , → MENU Gamma correction changes the luminance of the colors with intermediate luminance.
Changes the clearance of image. Available in analog Mode Only Sharpness MENU → , → , → → → , → MENU Changes the horizontal position of the monitor's entire display. H-Position Available in analog Mode Only MENU → , → , → → → , → MENU Changes the vertical position of the monitor's entire display. V-Position Available in analog Mode Only MENU → , → , → → → , → MENU OSD Menu Description You can choose one of eight languages.
MENU → Transparency → → , → , → → MENU Change the transparency of the background of the OSD. MENU → Display Time , , → → , → , → → MENU The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off. - 5 Sec, 10 Sec, 20 Sec, 200 Sec MENU → , → → , → , → → MENU Setup Menu Image Reset Description Image parameters are replaced with the factory default values.
Menu Information Description Shows a video source, display mode on the OSD screen.
Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom Check List Solutions No images on the screen. I cannot turn on the monitor. Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? Check the signal cable connection.
I cannot see the On Screen Display. Have you locked the On Screen Display (OSD) Menu to prevent changes? Unlock the OSD by pressing the [ The screen shows strange colors or just black and white. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection. Have the screen colors become strange after running a program or due to a crash between applications? Reboot the computer.
→ After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune MagicTune™ doesn't work properly. Have you changed your PC or video graphic card? Download the latest program. The program can be downloaded http://www.
How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor. Self-Test Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
Specifications General Model Name SyncMaster 711ND LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog, 0.
Signal Cable 15pin to 15pin D-sub cable, Detachable, 1.8 m Signal Connectors 15pin 3-row D-Sub connector Power Consumption Less than 45 W Dimensions (W x D x H) / Weight 370.0 x 60 x 316.0 mm / 14.6 x 2.4 x 13.5 inch (Without Stand) 370.0 x 200 x 404.0 mm / 14.6 x 7.9 x 15.9 inch (With Basic Stand) / 5.8 kg VESA Mounting Interface 100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.
Local Device (USB) Connection Speed When booting up a monitor, a blank screen may appear for 3 ~ 4 seconds until the MagicNet screen appears. If you turn the monitor off while booting, it may damage the product.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.
Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate.
Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 38 322 887 http://www.samsung.com/dk FINLAND 09 693 79 554 http://www.samsung.com/fi FRANCE 08 25 08 65 65 (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,12/Min) http://www.samsung.de HUNGARY 06 40 985 985 http://www.samsung.com/hu ITALIA 199 153 153 http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0.10/Min) http://www.samsung.
SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) http://www.samsung.com/mea Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit : mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user.
This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD sub pixels that is contained in this product are 3,932,160. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out softly. If excessive force is applied, you can have a stain on it.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
