LCD DISPLAY quick start guide 700TSn-2,820TSn-2 ii
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type.
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. both sides of the package box. Remove the Styrofoam and vinyl cover.
Introduction LCD Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all locations) MagicInfo Software CD, MagicInfo Manual CD Cables Power Cord D-Sub Cable Remote Control Batteries (AAA X 2) (BP59-00138A) (Not available in all locations) Others Sold separately RGB to BNC Cable DVI Cable Wall Mount KIT 10 LAN Cable
Introduction Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, press the button to adjust volume.
Introduction Use this button for turning the LCD Display on and off. Brightness Sensor (Optional) Automatically detects the surrounding brightness it accordingly. Note This function is activated only on the models equipped with an auto brightness sensor. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions.
Introduction RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB/COMPONENT IN (PC Connection Terminal (Input)) • Use a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) • Connect the RGB/COMPONENT IN port on the monitor to the COMPONENT port on the external device using the D-SUB to COMPONENT cable. • Connect the RGB/COMPONENT IN port on the monitor to the BNC port on the PC using the D-SUB to BNC cable.
Introduction Note Up to 6 Full HD or 10 HD monitors can be connected (May differ depending on the product). AV IN [VIDEO] Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable. AUDIO OUT Headphone/External speaker output terminal. HDMI IN Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. Up to HDMI cable 1.0 can be supported.
Introduction RGB OUT LAN (LAN Connection Terminal) USB1,USB2 (USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. Note See Connecting Cables for further information regarding cable connections. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. POWER OFF Number Buttons DEL / GUIDE button + VOL SOURCE D.
Introduction 1. POWER Turns the product On. 2. OFF Turns the product Off. 3. Number Buttons 4. DEL ton / GUIDE but- Press to change the channel. The "-" button is used to select Digital channels. Electronic Program Guide (EPG) display. - This function does not work for this LCD Display. 5. + VOL - Adjusts the audio volume. 6. Press the button to change the input signal SOURCE. SOURCE Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time. 7.
Introduction broadcasting type by using the DUAL button on the remote control while watching TV. 14. ENTER/PRE-CH This button is used to return to the immediately previous channel. - This function does not work for this LCD Display. 15. MUTE Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio comes back on if MUTE or - VOL + is pressed in the Mute mode. 16. CH/P In TV mode, selects TV channels.
Introduction LCD Display Head Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display.
Introduction Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction There are two hinges(left and right). Use the correct one. 2. A- Captive Screw B- Wall Bracket C- Hinge (Left) D- Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.
Introduction 1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes. • Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. 3.
Introduction A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. Note You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the left or the right side of the product to adjust the angle.
Introduction Mechanical Layout (820TSn-2) Mechanical Layout LCD Display Head Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.
Introduction • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket.
Introduction Wall Bracket(1) Hinge(Left 1, Right Plastic Screw 1) Hanger (A)(11) (4) Screw (B)(4) Anchor (11) Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. 1. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. 2.
Introduction A3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1.
Introduction 2. Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes. • Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. 3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. 4.
Introduction A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. Note You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the left or the right side of the product to adjust the angle.
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, RGB/COMPONENT IN port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the DVI IN port on the back of your LCD Display and the DVI port on the computer.
Connections Using the HDMI (digital) output on the graphics card. • Connect the HDMI IN port on the monitor to the HDMI port on the PC using the HDMI cable. Note When the HDMI cable to the PC, ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted. Note that sound is only available when connected according to the option that follows.
Connections • The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. Connecting AV Devices 1. Connect the Video and [R-AUDIO-L] port of the DVD, VCR or DTV Set-Top Box to the Video and [R-AUDIO-L] LCD Display. 2. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted. 3. Select AV using the SOURCE . Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder.
Connections Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. Connecting Using a DVI Cable 1. Connect between the DVI OUT port on the LCD Display and the input port on another monitor using a DVI cable. 2. Connect between the AUDIO OUT port on the LCD Display and the audio input port on another monitor using a stereo cable. 3.
Connections 2. Select HDMI using the SOURCE button on the front of the LCD Display or on the remote control. Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable 1. Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable. 2.
Connections Connecting the Touch Screen USB hub Note To use the touch screen function in MagicInfo mode, flip the toggle switch to the left. To use the touch screen function in PC mode, connect the USB port on your PC to the product using the USB cable and then flip the toggle switch to the right. Connecting a LAN Cable Connect the LAN cable.
Connections You can connect USB devices such as a mouse or keyboard.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: "Check Signal Cable" message.
Troubleshooting Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory.
Troubleshooting A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Q&A Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.
Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
