SyncMaster 510MP / 710MP
INDEX Main Page Adjusting Your LCD Monitor User Controls Safety Instructions Notational Power Installation Cleaning Other Introduction On-Screen Display Troubleshooting Check before Calling for Service Problems and Solutions Q&A Specifications Unpacking General Specifications Front PowerSaver Rear Preset Timing Modes Remote Control Information Setup Connecting Your Monitor Installing the Monitor Driver Installing a VESA Base Service Center Terms Regulatory Natural Color For Better Display Au
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage.
Installation Put your monitor in a location with low humidity and a minimum of dust. z An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or human body. Place the monitor on a flat and stable surface. z The monitor can cause injury by falling. Set down the monitor carefully. z It could be damaged or broken. Do not place the monitor face down. z The TFT-LCD surface may be damaged.
Cleaning When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly on the monitor. z This may cause damage, electric shock or a fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. z A dirty connector can cause an electric shock or fire.
타 Ohther Do not remove cover(or back). No user serviceable parts inside. z z This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. z This may cause an electric shock or fire. Be careful not to let water drip into the monitor or expose the monitor to moisture.
Ohther Do not use or store inflammable substances near the monitor. z This may cause an explosion or fire. Never insert anything metallic into the monitor openings. z This may cause an electric shock, fire or injury. Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor. z z This may cause malfunction, an electric shock or a fire.
Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Front For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor. The monitor's front configuration may vary slightly depending on the monitor model. 1. SOURCE button 5. Left-Right / Volume button 2. MagicBright™ button 6. MENU button 3. AUTO / EXIT button 7. Power button 4. Up-Down / Channel button 8.
Rear For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model. Remove the cover to connect the cables. (Pull the joining part to remove the cover.) A. Power port Connect the power cord for your monitor to the power port on the back of the monitor. B. Signal port Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. C.
Remote Control For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls > User Control Buttons > Remote Control buttons. The remote control's configuration may vary slightly depending on the monitor model. The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and right of the monitor's Remote Control Reception sensor. 1. Button Names 1. POWER button 2. MagicBright™ button 3. MUTE button 4.
Connecting to a Computer Turn on your computer and monitor. If your monitor displays an image, installation is complete. 1. Connecting to a Computer 1. Connect the power cord for your monitor to the power port on the back of the monitor. 2. Connect the signal cable to the video port on your computer. 3. Connect the audio cable for your monitor to the audio port on the back of your computer. 4. Turn on both your computer and the monitor. 5.
Connecting to other devices AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor. For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor. 1. Connecting AV Devices The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on. 1.
Connecting to other devices 2. Connecting TV You may view television programs on the monitor if it is connected to an antenna or CATV cable without installing any separate TV reception hardware or software on your computer. 1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor. You need to use a coaxial antenna cable. 2. Turn on the monitor. 3. Select TV using Source button among the external signal adjustment buttons. 4. Select a desired TV channel.
Connecting to other devices 4. Connecting Headphones You may connect your headphones to the monitor. 1. Connect your headphones to the Headphone-out port.
Installing the Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.
Installing the Monitor Driver 2. Windows XP/2000 Refer to "Installing the Monitor Driver and User Manual" CD-ROM supplied with the monitor. When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up automatically, click monsetup.exe twice in the CD-ROM drive folder of Windows Explorer. 1. Insert CD into the CD-ROM driver. 2. Click " Windows XP/2000 Driver". .3 Choose your monitor model in the model list, then click the " OK" button. .
Installing the Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.
Installing the Monitor Driver 4. Click the Properties" button on the " Monitor" tab and select " Driver" tab. 5. Click " Update Driver.." and select " Install from a list or.." then click " Next" button. .6 Select " Don't search ,I will.." then click " Next" and then click " Have disk". 7. Click the " Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the " Next" button.
Installing the Monitor Driver 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. h T is monitor driver is under certifying MS logo,and this installation don't damage your system. h T e certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/ .9 Click the " Close" button then click " OK" button continually. 10. Monitor driver installation is completed.
Installing the Monitor Driver 케이블 연결 2. Microsoft® Windows® 2000 Operating System * When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose " OK" button on the " Insert disk" window. 2. Click the " Browse" button on the " File Needed" window. 3. Choose A:(D:\Driver) then click the " Open" button and then click " OK" button. * How to install 1. Click " Start" , " Setting" , " Control Panel". 2. Double click the " Display" Icon. .
Installing the Monitor Driver 케이블 연결 4. Microsoft® Windows® NT 4.0 Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings a T b and then click All Display Modes. .3 Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. .4 Click Apply button if you see the screen working normally after clicking Test.
Installing a VESA base The monitor may be reclined from 0 to 90 degrees. When fully folded (reclined), the base becomes a handy holder for moving the monitor around. 1.
Installing a VESA base 케이블 연결 2. Folding Base You may install a VESA base when the monitor base is fully folded.
Installing a VESA base 케이블 연결 The monitor supports VESA mounting standard for use with various VESA mounting devices. This monitor accepts a 75mm x 75mm VESA-compliant mounting interface pad. You need to fold the monitor base before installing a VESA base. Align the four bolt holes the base with the four bolts on the monitor base with the holes on the VESA base and then fasten supplied. Only the supplied bolts should be used.
User Controls 케이블 연결 The control button configuration may vary slightly depending on the monitor model. Monitor Buttons For more information about screen adjustment, refer to On-Screen Display. 1. Source button Turns on the indicator to indicate the currently displayed input signal. To switch Screen modes : PC TV Video S-Video (Press here to view Screen Mode Switching Animation Clips) 2.
User Controls Remote Control Buttons For more information on the screen adjustment functions, refer to On-Screen Display. 1. POWER button 2. MagicBright™ button 3. MUTE button 4. AUTO / Previous channel button 5. CAPTION button 6. CHANNEL button 7. SOURCE button 8. Up-Down / Channel button 9. Left-Right / Volume button 10. MENU button 11. EXIT button 12. +100 button 13. DISPLAY button 1. Power button Use this button to turn the monitor on and off. 2.
User Controls 케이블 연결 Remote Control Buttons For more information on the screen adjustment functions, refer to On-Screen Display. 1. POWER button 2. MagicBright™ button 3. MUTE button 4. AUTO / Previous channel button 5. CAPTION button 6. CHANNEL button 7. SOURCE button 8. Up-Down / Channel button 9. Left-Right / Volume button 10. MENU button 11. EXIT button 12. +100 button 13. DISPLAY button 8. Up-Down / Channel button Moves from one menu item to another vertically or adjusts the selected menu value.
User Controls 케이블 연결 Direct-Access Features let you display Monitor Adjustment Menu by simply pressing Auto button once. Or they are used to adjust monitor functions. You need to activate functions other than Auto Adjustment only when Auto-Access Features are off. Auto Adjustment | OSD Lock/Unlock | Volume | Channel 1. Auto Adjustment The monitor display becomes more stabilized if adjusted by Auto Adjustment functions when the monitor is installed for the first time.
User Controls 케이블 연결 3. Volume When OSD is not on the screen, push the 1. Push the 2. Push the or button to adjust volume. button to decrease the volume. button to increase the volume. 4. Channel When OSD is not on the screen, push the number. 1. Push the 2. Push the or button to select channel button to decrease the channel number. button to increase the channel number. This function is available in TV mode only.
On-Screen Display Characters and icons become highlighted in blue during adjustment for each menu. 1. PC Screen For detailed information on Screen Adjustment in the PC mode, refer to PC Screen Adjustment Animation Clips. Contrast Adjust Contrast. Brightness Adjust Brightness. Color Control The tone of color can be changed from redish white to bluish white. The individual color components are also user customizable. 1) Normal : Plain white. 2) Warm : Reddish white. 3) Cool : Bluish white.
On-Screen Display 케이블 연결 2. TV Screen For detailed information on Screen Adjustment in TV mode, refer to TV Screen Adjustment Animation Clips. Screen Adjustment in TV mode does not affect the PC screen at all. Channel The channel system can be set in several different ways. 1) ANT / CATV Select a channel system that is being used in your region. • ANT • STD • HRC • IRC • AFN STD, HRC, IRC and AFN identify various types of cable TV systems.
On-Screen Display 케이블 연결 3. Video Screen For detailed information on Screen Adjustment in the Video mode, refer to Video Screen Adjustment Animation Clips. Screen Adjustment in the Video mode does not affect the PC screen at all. Picture Controls Video screen properties such as Contrast, Brightness, Sharpness, Color and Tint. 1) Contrast : Adjust the contrast of video without affecting PC RGB's contrast. 2) Brightness : Adjust the brightness of video without affecting PC RGB's brightness.
On-Screen Display 5. OSD Control For detailed information on screen adjustment functions, refer to OSD Screen Adjustment Animation Clips. Language You can choose one of 4 languages. (English, French, Spanish, Portuguese) Note: The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Position Move the OSD Window to the vertical and horizontal direction. Halftone Change the opaqueness of the background of the OSD.
Check before calling for service 케이블 연결 Check the following items yourself before calling for service. Contact the service center for problems that you cannot solve by yourself. Self-Test Feature Check | Video mode not supported | Display Adapter Driver | Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
Check before calling for service 3. Display Adapter Driver Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot install the monitor driver. 1. Checking Adapter Driver Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced --> Adapter. If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly installed.
Problems and Solutions The following table lists possible problems and their solutions. Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. 1. Problems related to Installation Problems related to the monitor installation and their solutions are listed.
Problems and Solutions Problems Picture image is unstable and vibrates. Solutions z Ghost images are shown in the picture. The image is too light or too dark z Screen color is inconsistent. z Check if the resolution and frequency set for the computer video card falls in the range supported by the monitor. If not, reset them referring to the current Information under the monitor menu and Preset Timing Modes. Adjust the Brightness and Contrast.
Q&A Frequently asked questions are summarized here for your reference. Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows XP: Reset resolution by clicking Control Panel Theme Display Settings. Windows ME/2000: Set the resolution at the Control Panel Settings.
General Specifications Design and specifications are subject to change without prior notice. General Model Name SyncMaster 510MP LCD Panel Size 15.0 inch (Diagonal) Display area 304.1 (H) x 228.1 (V) Pixel Pitch 0.297 (H) x 0.297 (V) Type a-si TFT active matrix Synchronization Horizontal 31 ~ 61 kHz Vertical 56 ~ 75 Hz Display Color 16,194,277 Colors Resolution Optimum resolution 1024 x 768@60Hz Maximum resolution 1024 x 768@75Hz Input Signal, Terminated RGB Analog, Composite H/V, 0.
General Specifications SyncMaster 510MP Environmental considerations Operating Temperature : 50°F ~ 104°F(10°C ~ 40°C) Humidity : 10% ~ 80%, non-condensing Storage Temperature : -4°F ~113°F (-20°C ~ 45°C) Humidity : 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings.
General Specifications Design and specifications are subject to change without prior notice. General Model Name SyncMaster 710MP LCD Panel Size 17.0 inch (Diagonal) Display area 337.92 (H) x 270.336 (V) Pixel Pitch 0.264 (H) x 0.264 (V) Type a-si TFT active matrix Synchronization Horizontal 31 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,194,277 Colors Resolution Optimum resolution 1280 x 1024@60Hz Maximum resolution 1280 x 1024@75Hz Input Signal, Terminated RGB Analog, Composite H/V, 0.
General Specifications SyncMaster 710MP Environmental considerations Operating Temperature : 50°F ~ 104°F(10°C ~ 40°C) Humidity : 10% ~ 80%, non-condensing Storage Temperature : -4°F ~113°F (-20°C ~ 45°C) Humidity : 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings.
PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
Preset Timing Modes SyncMaster 510MP If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.
Preset Timing Modes SyncMaster 710MP If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.
Service Center U.S.A. : Samsung Computer Products Customer Service 400 Valley Road, Suite 201, Mt. Arlington, NJ 07856 Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864) Fax. : (973)601-6001 http://www.samsungusa.com/monitor/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc. 7037 Financial Drive Mississauga, Ontario L5N 6R3 Tel.
Service Center PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA S.A. Rua Mário Dioniso, No2 - 1° Drt. 2795-140 LINDA-A-VELHA Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120 http://www.samsung.pt/ NETHERLANDS/BELGIUM/LUXEMBOURG : Samsung Electronics Benelux B. V. Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS Service and informatielijn ; Belgium :0800-95214, http://www.samsung.be/ Netherlands : 0800-2295214, http://www.samsung.nl/ CHILE : SONDA S.A.
Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Types of Sync Signals Separate This is a scheme of transmitting individual vertical sync signals to the monitor. Composite This is a scheme of combining vertical sync signals into one composite signal and transmitting it to the monitor.
Regulatory FCC Information | IC Compliance Notice | MPR II Compliance | European Notice (Europe only) | PCT Notice | VCCI | TCO'95-Ecological requirements for personal computers (TCO'95 applied model only) TCO'99-Ecological requirements for personal computers (TCO'99 applied model only) TCO'03-Ecological requirements for personal computers (TCO'03 applied model only) TCO'03 Recycling Information (TCO'03 applied model only) FCC Information User Instructions The Federal Communications Commission Radio Freque
Regulatory MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice (Europe only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
Regulatory TCO'95-Ecological requirements for personal computers (TCO'95 applied model only) AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
Regulatory Environmental Requirements Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances. These are related to another group of environmental toxins, PCBs, which are suspected to give rise to similar harm, including reproductive damage in fish eating birds and mammals, due to the bioaccumulative processes.
Regulatory TCO'99-Ecological requirements for personal computers (TCO'99 applied model only) Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Regulatory Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Regulatory TCO'03-Ecological requirements for personal computers (TCO'03 applied model only) Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.
Regulatory TCO'03 Recycling Information (TCO'03 applied model only) For recycling information for TCO'03 certified monitors, for the residents in the following countries, please contact the company corresponding to your region of residence. For those who reside in other countries, please contact a nearest local Samsung dealer for recycling information for the products to be treated in environmentally acceptable way. [U.S.A. Residents Only] COMPANY ADDRESS [European Residents Only] U.S.A.
Natural Color Natural Color Software Program One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
For Better Display For Better Display 1. Adjust computer resolution and screen injection rate (refresh rate) in control panel of computer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. SyncMaster 510MP { { Resolution: 1024 x 768 Vertical frequency (refresh rate): 60 Hz SyncMaster 710MP { { Resolution: 1280 x 1024 Vertical frequency (refresh rate): 60 Hz 2.
Authority Information in this document is subject to change without notice. © 2003 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
