LCD MONITOR quick start guide 320 PX ii
Select Language Main Page Model Safety Instructions Introduction Package Contents Your LCD Display Machanical Layout Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Batteries (AAA X 2) Remote Control (Not available in all Cover-Hole locations) BNC to RCA Adaptor Jack Semi Stand Sold separately Wall Mount KIT Speaker Set DVI Cable BNC Cable Stand KIT Your LCD Display Front 1) MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2) Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values.
Activates a highlighted menu item. 5) SOURCE Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] → [BNC] → [DVI] → [AV] → [S-Video] → [Component] >> Click here to see an animation clip. 6) PIP Push the PIP button to turn the PIP screen On / Off. More than one PIP cannot overlap on screen as BNC and the component use the same terminal. >> Click here to see an animation clip.
MDC(Multiple Display Control) Program Port 2) DVI / PC IN [RGB] (PC Video Connection Terminal) Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) 3) DVI / PC IN [DVI(HDCP)] (PC Video Connection Terminal) Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) 4) DVI / PC IN [PC/DVI/BNC AUDIO IN] (PC/DVI/BNC Audio Connection Terminal (Input)) 5) COMPONENT AUDIO IN [L-AUDIO-R] (Component Audio Connection Terminal (Input)) 6) BNC/COMPONENT OUT [R/PR, G/Y, B/PB, H, V] (BNC/Component Connectio
For using a locking device, contact the place of purchase. Note • See Connecting the LCD Display for further information regarding cable connections. Remote Control Note • The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. 1. ON / OFF 2. MAGICNET 3. MDC 4. LOCK 5. MagicNet buttons 6.+100 -/-7. VOL 8. MUTE 9. TTX/MIX 10. MENU 11. ENTER 12. P.MODE 13. AUTO 14. PRE-CH 15 .
- This fuction does not work for this monitor. 7) VOL Adjusts the audio volume. 8) MUTE Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. TTX/MIX 9) TV channels provide text information services via teletext. - This fuction does not work for this monitor. 10) MENU Opens the on-screen menu and exits from the menu screen or closes the screen adjustment menu.
SRS DUAL/MTS 25) DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. MTSYou can select MTS (Multichannel Television Stereo) mode. Audio Type MTS/S_Mode FM Stereo Mono Mono Stereo Mono ↔ Stereo SAP Mono ↔ SAP Default Manual Change Mono - This fuction does not work for this monitor. 26) PIP Every time you press the button, a PIP screen appears.
Select Language Main Page Model SyncMaster 320PX Safety Instructions Introduction Connections Installing the Stand KIT Connecting the LCD Display Using the Software The color and appearance of the product may vary depending on the model, and the product specifications are Adjusting the LCD Display subject to change without prior notice for reasons of performance enhancement.
This stand is designed for adjusting the screen angle. The company is not responsible for any problem caused when using this stand. Under no circumstances use the product as a stand for placing something on. Installing the Stand KIT (sold separately) 1) A 'Cover-Protector' is used to protect the hole at the bottom of the LCD Display , where the stand is inserted.
1) Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Trun on the power switch. 2) There are 3 ways to connect the D-sub to your LCD Display. Choose one of the following: 2-1) Using the D -sub (Analog) connector on the video card. Connect the D -sub to the 15-pin, RGB port on the back of your LCD Display and the 15 pin D sub Port on the computer. 2-2) Using the DVI (Digital) connector on the video card.
Connecting Digital DVD Note • Input devices such as digital DVD are connected to the DVI IN terminal of the monitor using the DVI cable. • Then, start the DVD with a DVD disc inserted. • Select Digital using the SOURCE button. Note • The monitor has DVI IN connection terminals to connect DVI input devices digital DVD. Connecting to a VCR 1) AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S -VIDEO] of the LCD Display using an S-VHS or BNC cable.
1) Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the DVD player. 2) Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the DVD player. Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the DVD Player with a DVD disc inserted.
• The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. Connecting to a DTV Set Top Box Note • The connections for a typical Set Top Box are shown below. 1) Connect a Component cable between the BNC / COMP ONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the Set Top Box.
Note • Connect the speaker connection cable between the speaker connection jack on the back of the SET and the speaker connection jack on the back of the speaker. Note • Do not move the SET while the SET is connected to the speakers. The speaker-bracket for connecting the SET speaker my become damaged. Connecting to an Audio System Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the AUDIO OUT [L-AUDIO-R] on LCD Display. © 1995~2007 SAMSUNG.
Select Language Main Page Model SyncMaster 320PX Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Self-Test Feature Check Check List Q&A Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Note • Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a Samsung cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly.
Problems related to the Installation (PC Mode) Note • Problems related to the LCD Display installation and their solutions are listed. Problems The LCD Display screen flickers. Solutions z Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note • Problems related to the LCD Display screen and their solutions are listed.
The screen is blank and it is z If you see the "TEST GOOD" message on the screen when you pressing the MENU button, check the cable connection between blinking. the LCD Display and the computer to ensure that the connector is properly connected. Problems related to Audio Note • Problems related to audio signals and their solutions are listed below. Problems No sound.
the Windows / Computer Manual). How can I clean the outer Disconnect the power cord and then clean the LCD Display with a soft case/LCD Panel? cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the LCD Display. © 1995~2007 SAMSUNG.
