Pre-Installation & Installation Manual Frameworx LCD Interface February 2012 / 57-900073-000
Frameworx LCD Interface Pre-Installation & Installation Manual © February 2012 by the Brunswick Bowling and Billiards Corporation. All rights reserved. Frameworx is a registered trademark of the Brunswick Bowling and Billiards Corporation. Reorder Part No. 57-900073-000 Notice: If available, updates to this manual can be found on-line at www.brunswickbowling.com. Confidential proprietary information. All information contained in this document is subject to change without notice.
SAFETY Throughout this publication, “Warnings”, and “Cautions” (accompanied by one of the International HAZARD Symbols) are used to alert the mechanic to special instructions concerning a particular service or operation that may be hazardous if performed incorrectly or carelessly. They are defined below. OBSERVE AND READ THEM CAREFULLY! These “Safety Alerts” alone cannot eliminate the hazards that they signal.
SAFETY NOTICE TO USERS OF THIS MANUAL This manual has been written and published by the Service Department of Brunswick Bowling and Billiards to aid the reader when servicing or installing the products described. It is assumed that these personnel are familiar with, and have been trained in, the servicing or installation procedures of these products, which includes the use of common mechanic’s hand tools and any special Brunswick or recommended tools from other suppliers.
Table of Contents Packaging......................................................................................................................................6 Site Survey..................................................................................................................................10 Interface Overview......................................................................................................................14 Interface Power Supply pre-Installation...........................
Packaging Page 1 of 1 Drawing Number: E3-300434-000 Rev. No: DESCRIPTION: MNC - FRAMEWORX LCD INTERFACE, FOR DOMESTIC REV. QTY. PART NUMBER 1.00 1.00 1.00* 2.00 1.00 1* 57-500527-000 57-861288-000 57-861441-400 57-863035-000 57-863382-400 57-900073-000 DESCRIPTION OF PACKAGE CABLE – IEC 320/C14 MALE TO IEC 320/C13 FEMALE PKG. - CABLE, POWER CORD, 7.5' LONG PKG. - FRAMEWORX LCD OVERHEAD SCRIPT FILES PKG. - CABLE, RS232 SERIAL, 6' NULL MODEM PKG.
Page 1 of 1 Drawing Number: E3-300433-000 Rev. No: DESCRIPTION: MNC - 46" SAMSUNG LCD DISPLAY, 220V REV. QTY. 1.00 PART NUMBER 57-863369-002 DESCRIPTION OF PACKAGE PKG. - MONITOR, 46" SAMSUNG 460MX-3, 220V Page 1 of 1 Drawing Number: E3-300432-000 Rev. No: DESCRIPTION: MNC - 40" SAMSUNG LCD DISPLAY, 220V REV. QTY. PART NUMBER 1.00 57-863368-002 DESCRIPTION OF PACKAGE PKG. - MONITOR, 40" SAMSUNG 400MX-3, 220V Page 1 of 1 Drawing Number: E3-300426-000 Rev.
Page 1 of 1 Drawing Number: E3-300421-000 Rev. No: DESCRIPTION: MNC - 32" SAMSUNG LCD DISPLAY, JAPANESE REV. QTY. PART NUMBER 1.00 57-863361-002 DESCRIPTION OF PACKAGE PKG. - MONITOR, 32" SAMSUNG 320MX-3, JAPANESE Page 1 of 1 Drawing Number: E3-300448-000 Rev. No: N/C DESCRIPTION: MNC - LCD MOUNTING BRACKET, WIDESCREEN, FOR CONTINUOUS REV. QTY. PART NUMBER 1.00 57-863325-000 DESCRIPTION OF PACKAGE PKG. - UNIVERSAL MOUNTING BRACKET, WIDESCREEN FOR CONTINUOUS OR STD.
Page 1 of 1 Drawing Number: E3-280102-000 Rev. No: N/C DESCRIPTION: MNC - VECTOR ANIMATIONS FOR FRAMEWORX - SET 2 REV. QTY. PART NUMBER 1.00 57-863352-400 DESCRIPTION OF PACKAGE PKG. – VECTOR ANIMATIONS FOR FRAMEWORX - SET 2 Page 1 of 1 Drawing Number: E3-280103-000 Rev. No: N/C DESCRIPTION: MNC - VECTOR ANIMATIONS FOR FRAMEWORX - SET 3 REV. QTY. PART NUMBER 1.00 57-863353-400 DESCRIPTION OF PACKAGE PKG.
Site Survey This site survey is to be completed by the sales team before order submission. 1. Verify the type of "Remote Video Board" the center has. There are two locations the "Remote Video Boards" can be located, in the Lane Group Processor (LGP) or the shaver console. Refer to Figures 1 & 2. The LGP is located on the curtain wall. If there is not an LGP then the "Remote Video Board" is located inside the shaver scoring console. Figure 1. Lane Group Processor Remote Video Board Location Figure 2.
IMPORTANT! The "Remote Video Boards" do not have to be removed to identify the part number. a. Does the center have video board, part number 57-300103-4xx? ______ b. Does the center have the 2000 video board, part number 57-301081-4xx? ______ c.
4. Does the center have TV-Only monitors currently installed? If No, skip to question 5. a. Does the center want to turn the TV-only monitor on or off from the front desk? i. If yes, then the FX LCD upgrade is required; specify the appropriate number of FX LCD upgrade tab codes needed for TV-Only monitors. ii. If No, see part c. b. Does the center want to use the existing AV Box? i.
6. What type of front desk does the center have? a. Command Network _______ b. Center Master _______ c. Vector Plus _______ 7. What version of Frameworx scorer software does the customer have? _______ NOTE: Command Network must have Frameworx scorer software version 5.6. Vector Plus and Centermaster must have Frameworx scorer software version 6.3. If the customer does not have the proper software, please contact the CRC on behalf of the customer to obtain these disks.
Interface Overview Figure 3.
LCD Wide Screen Overhead Installation The LCD Wide Screen Overhead must be assembled with brackets and the LCD Interface before it can be installed on the weldment. Quantity One per LCD widescreen One per LCD widescreen Package Number 57-863325-000 57-863326-000 Description Hanging Brackets Hardware 1. After removing the LCD wide screen from it's package, set on foam packaging. Be sure not to scratch or damage LCD while assembling the hanging brackets and LCD Interface. 2.
3. Hang the LCD wide screen on the weldment. Use the handles of the LCD wide screen to raise into position. Refer to Figure 2. Figure 2.
4. Install the bracket lock (P/N 57-500757-001), to the hanging bracket. After the bracket lock is installed, use the M6 x 40mm screw (P/N 11-053784-009) to secure it in place. Refer to Figure 3. Figure 3.
Secure Interface Assembly to to LCD hanger brackets Figure 4.
Overview of Interface Figure 5. Frameworx LCD Interface Board I/O Connectors Location and Description The functions of the connectors and components of the Frameworx LCD Interface are: (1) Video In - The video input connector for the Frameworx video signal. (2) Video Out - The loop through Frameworx video signal (to the next lane) (3) LAN IN: The RS-485 serial communication input connector for the Frameworx communication channel.
(5) Power In - Use a power cable from an outlet of the building power to the "Power In" port of the LCD (6) Power Out - Use power cable (57-500527-000) to power the LCD from the "Power Out" port of the Interface (7) RGB Output - RGB output is red, green, blue and composite sync output for any LCD monitor that can accept analog RGB video signals with Composite Sync. The horizontal frequency is 15.72 kHz and vertical is 59.92 Hz.
Old Frameworx CRT Monitor Cabling TV-Only Figure 6.
Scoresheet Video Figure 7.
LCD INTERFACE CABLING Frameworx Scorer Cabling Figure 8.
LCD Cabling Figure 9.
DIP Switch Location and Configuration DIP Switch Location Figure 10. DIP Switches Figure 10 shows the Frameworx LCD Interface PCB DIP switch locations and descriptions: (1) SW1: position switch for LCD monitor selection. See Figure 11 for switch settings and LCD monitor selection. (2) SW2: 4 position DIP switch for video cable termination. The switch default is all switches are ON. The video cable is then terminated for each signal, red, green, blue and composite snyc with 124 Ohms resistors.
Configuration SW1 (Switch 1) Manufacturer of Monitor Brand Compatibility LEGACY NEC NEC 4000 NEC NEC MULTISYNC LG LG L3200T SAMSUNG SYNCMASTER 323T & 403T OLEVIA OLEVIA 232 OLEVIA OLEVIA 242 & 237 OLEVIA OLEVIA 232T12, 232 & S13 SAMSUNG SYNCMASTER MX SERIES DEBUG MONITOR Description LEGACY monitor is selected. This is an unsupported monitor. NEC 4000 monitor is selected. This is an unsupported monitor.
Monitor Type Switch Settings OVERHEAD TV this Frameworx LCD controller is connected to a Center TV. OVERHEADSCORE SHEET MONITOR this Frameworx LCD controller is connected to an Overhead Scorer Monitor. Figure 12. Switch 1 - Monitor Type Testing Switch Settings OVERRIDE 1 forces the monitor ON unconditionally and ignores Scorer communications. OVERRIDE 2 allows the Scorer to control the monitor. Figure 13.
Software Installation IMPORTANT!: Install Batch files before upgrading CRT overheads to LCD this will avoid graphic card compatibility problems. 1. Log onto the system with an user I.D that has administrative rights. 2. Load the CD on the Centermaster/Vector Plus server. Description of files to be downloaded: - FRXLCD.SCP script file - Configures the Frameworx Scorer to use LCD overheads. UNFRXLCD.SCP script file - Changes the Frameworx Scorer to use CRT overheads. CER_CHIP.
3. Type FRXLCD.SCP in the other box. Figure 17.
4. Download the "FRXLCD.SCP" file to the Frameworx Scorer by pressing the “Other” button. NOTE: The Frameworx scorer will reboot automatically after the file is downloaded. Figure 18. Software Installation To use the CRT overheads follow steps 1 through 4 except use file “UNFRXLCD.SCP” in step 3. Command Network 1. Load the floppy or the Card Net/Dsk card server. At the Lane Status screen: 30 1. Press SCORER STATUS. 2. Type the lane number(s) that will be affected and press ADJUST. 3.
NOTE: The Frameworx scorers will reboot automatically after the file is downloaded. During this time the screen will display “Processing.” After the Frameworx score reboot is complete, the screen will display “Successful” or “Failed.” When the scorers have finished rebooting successfully, you may issue the lanes as normal. If the function failed, contact the Brunswick Customer Response Center for assistance. Jumper Settings and Description Figure 19.
(5) Jumper, JP5 - is the vertical sync signal selection jumper for PrPbY conversion. Default is open, no vertical sync selection. (6) Jumper, JP6 - is the horizontal sync signal selection jumper for PrPbY conversion. Default setting is 2-3 position, horizontal sync is same as composite sync from scorer. (7) Jumper, JP7 - is the Vertical Sync select jumper. Default setting is open position. Jumper closed will connect vertical sync signal on pin 14 at output RGB connector J5.
(21) Jumper, JP21 is the CS_ON select jumper. Default setting is on pins 2-3. The CS_ON signal will be self generated when Composite Sync signal from Frameworx scorer is present. With jumper on pins 1-2 position, the CS_ON signal will be generated and controlled with microcontroller. CS_ON signal can control optional relay if it is connected on J13 connector. (22) Jumper, JP22 - is the address select jumper for optional I2C EEPROM U28. Default setting is open, EEPROM is on address 01H.
(2) LED, D4 - is the RS-485 transmitting LED. The LED is blinking when the microcontroller is transmitting data to the RS-485 serial network. (3) LED, D5 - is a heart-beat LED. The LED is blinking when the microcontroller U10 is running. (4) LED, D8 - is board transmitting or receiving LED for RS-485 communication to the Frameworx Scoring computer. The LED is light ON if the board is in receiving mode. The LED is turn OFF if interface board is in transmitting mode.
Cable Prints Primary Console Global Video Front Control Desk Cable Assembly (P/N 57-300004-000) Overhead Monitor Video Input Cable Assembly (P/N 57-300026-000) Overhead Monitor Video Input Cable Assembly (P/N 57-300027-000) Local LAN Frameworx 27" TV-Only Overhead Cable Assembly (P/N 57-300031-000) Frameworx to LCD Interface Pre-Installation & Installation 35
Overhead TV-Only Lane Pair, to Lane Pair Cable Assembly (P/N 57-300139-000) Cable IEC 320 / C14Male to EC 320 / C13 Female.
