SyncMaster 2280HD SyncMaster 2280HD Install drivers
Model SyncMaster 2280HD Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.
z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. (Class l Equipment only.) Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.
Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. z Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor.
z Any increase in the internal temperature may cause fire. Put down the monitor carefully. z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly onto the monitor. z This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center. z This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. z z This may cause a malfunction, electric shock or fire.
Never insert anything metallic into the monitor openings. z This may cause electric shock, fire or injury. Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
Place the product out of children's reach, as they could damage by hanging onto it. z A falling product may cause injury to the person or even fatality. When not using the product for an extended period of time, keep the product unplugged. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product.
height so that the top of the monitor is slightly below eye level. z Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. z Keep your arms level with the back of your hands. z Keep the angle of the elbow perpendicular. z Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
Model SyncMaster 2280HD Features Features of Digital Broadcasting - All multimedia broadcasting processes including program creation, transmission, and receiving are processed digitally, which allows users to enjoy a very high screen quality without any signal loss as well as benefit from various additional services.
Without Stand With Stand Manual Quick Setup Guide Warranty Card (Not available in all locations) User's Guide, Monitor Driver Cable D-Sub Cable BN39-00244B Power Cord 3903-000085 CBF-stereo Cable BN39-00061B Remote Control BN59-00580A Batteries (AAA X 2) 4301-000121 Cleaning Cloth Other Sold separately
RCA Cable (Video-Yellow, Audio-Red and White) Audio cable Component(PR, PB, Y) Cable TV Antenna Cable (Coaxial Cable) S-VIDEO Cable Earphones/Headphones HDMI Cable Digital audio optic output cable DVI Cable This is an accessory that can be added depending on the model. Front 1. TV/DTV 2. PIP 3. 4. – + 5. MENU 6. 7. Remote Control Sensor 8. [ ] Power button 9. Power indicator 10. Speaker 1. TV/DTV This button is used to switch between normal and DTV broadcasting signals. 2.
3. Moves from one menu item to another vertically or adjusts selected menu values. In TV/DTV mode, selects TV/DTV channels. 4. – + Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. 5. MENU Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. 6. Press the ' ' button to change the input signal source.
(The configuration at the back of the monitor may vary from product to product.) 1. POWER z 2. HDMI IN/PC Power terminal Connect the power cord for your monitor to the POWER on the back of the monitor. This product may be used with 100 ~ 240VAC(+/- 10%). 1. HDMI IN : Connects to the HDMI jack of a device with an HDMI output. No sound connection is needed for an HDMI to HDMI connection. Use the HDMI IN terminal for a DVI connection to an external device.
output terminal of the external device using a VIDEO cable. 3. S-VIDEO : Connect the [S-VIDEO] terminal of your monitor to the SVIDEO output terminal of the external device using a S-VIDEO cable. 4. ANT IN 1. Connects to an air antenna. 2. Connects to a cable system. For more information on how to connect antennas, see "Connecting TV" in the Installation section. 5. DVI/PC IN 1. DVI-D : Connect the DVI cable to the [DVI-D] port on the back of your monitor. (With DVI, only PC input signals are supported.
8. z 9. Kensington Lock z Connect your headphones to the Headphone connection terminal[ ]. The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. See Connecting the monitor for further information regarding cable connections. Contact a Service Center to purchase any products sold separately.
2. Number button 3. - button 4. TV/DTV 5. CH LIST 6 + VOL - 7. MUTE 8. MENU 9. 10. Up-Down Left-Right buttons ENTER 11. SOURCE 12. PRE-CH 13. ANTENNA 14. ADD/DEL 15. CH 16. EXIT 17. PIP 18. INFO 19. SLEEP 20. P.MODE, M/B 21. S.MODE 22. AUTO 23. P.SIZE 24. SOURCE 25. POSITION 26. SIZE 27. MTS 1. POWER Turns the monitor On/Off. 2. Number button Selects TV/DTV channels in the TV/DTV mode. Used to change channels when PIP is selected and the PIP SOURCE is set to TV/DTV. 3.
6. + VOL Adjusts the audio volume. 7. MUTE Press to mute the sound temporarily. Displayed on the bottom left of the screen. Press the MUTE button again to cancel the Mute function. Alternatively press the - VOL + buttons to cancel the Mute function. 8. MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. 9. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 10.
PC / DVI ( M/B=MagicBright™) MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes. ( Entertain → Internet → Text → Custom ) 21. S.MODE When you press this button, current mode is displayed on the lower center of the screen. The monitor has a built-in high fidelity stereo amplifier. Then press the button again to circle through available preconfigured modes.
Model SyncMaster 2280HD Connecting the monitor 1. Connecting to a Computer 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Use appropriate connection for your computer. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the [PC] port on the back of your monitor. [PC] 2-2. Using the DVI (Digital) connector on the video card.
2. Connecting to a Macintosh 1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the D-SUB port on the Macintosh computer. [PC] Turn on the monitor and Macintosh. Connecting to Other devices This monitor allows the user to connect it to such input devices as a DVD player, a VCR or camcorder, or a DTV or TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product.
the monitor using the AV or S-Video cable. 2. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [L- AUDIO-R] port of the monitor. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. Select AV or S-Video using the ' '. 2. Connecting TV - Connecting VHF and UHF Antennas If your antenna has a set of leads that look like the diagram to the right, see "Antennas with 300 Ω Flat Twin Leads" below.
bottom of the rear panel. 2. Connecting TV - Connecting Cable TV To connect to a cable TV system, follow the instructions below. 1. Cable without a Cable Box If you are using an off-air antenna (such as a roof antenna or "rabbit ears") that has 300Ω twin flat leads, follow the directions below. 1- Plug the incoming cable into the ANT 2 IN (CABLE) 1. terminal on the back of the TV. z Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels. 2.
3-5. Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch. 3-6. Connect the last RF cable between the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the set. After you have made this connection, set the A/B switch to the "A" position for normal viewing. Set the A/B switch to the "B" position to view scrambled channels.
2. Connecting HDMI You can connect digital output devices to your monitor. You can enjoy better screen and sound quality. 2-1. Connecting Using a HDMI Cable 1. Input devices such as digital DVD are connected to the [HDMI IN] terminal of the monitor using the HDMI cable. 2. When all the connections are completed, connect the power cords for the monitor and DVD (or the device connected to the digital output terminal). 3. Select "HDMI" using the ' ' button. 2-2. Connecting Using a DVI to HDMI Cable 1.
If you just connect using the DVI to HDMI cable without connecting to the sound source, you cannot hear sound. Connecting the audio output terminal of a digital device to the [R-AUDIO-L] of [AV IN] of the monitor using an audio cable will not give you sound. Make sure to connect to the [HDMI/PC DVI-D AUDIO IN] terminal of the monitor. 3.
z Connect your headphones to the Headphone connection terminal. Using the Stand This monitor supports various types of VESA-standard bases. You need to either fold or remove the base in use in order to install a VESA base. 1. Folding the base The monitor may be reclined from -1 to 23 degrees. 2. Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2.
four screws that came with the arm-type base, wall mount hanger or other base. To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10cm away from the wall surface. Contact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Please use Wall Mount according to the International standards.
Installing the Monitor Driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. z Internet web site : http://www.samsung.
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ 6. Click "Update Driver…" in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". 9.
10. Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System 1. Insert the CD into the CD-ROM driver. 2. Click "Start" click "Control Panel" and then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced.
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver." and select "Install from a list or." then click "Next" button. 6. Select "Don't search, I will" then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed.
4. Choose "Monitor." Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. 5. Click "Driver" and then click "Update Driver" then click the "Next" button. 6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk." 7.
Model SyncMaster 2280HD Input Available Source List : PC / DVI : TV : AV : S-Video : Component : HDMI The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Source List Use to select PC, TV or other external input source connected to the Monitor. Use to select the screen of your choice. The direct button on the remote control is "SOURCE" button.
super-imposed on the PC Video signal. (On/Off) When PIP is in operation, the sound in PIP Source will be selected. While V-Chip is in operation, the PIP function cannot be used. - Available in PC/DVI Mode Only PIP : Turn the PIP Screen on or off. Off / On The direct button on the remote control is "PIP" button. - MENU → ＋ → ＋ → ▼ → ＋ → ▼▼ → Source : Select the input source for the PIP.
Available Mode : PC / DVI : TV : AV : S-Video : Component : HDMI The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Play/Stop MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Entertain, Internet, and Text.
Color Control Adjusts the individual R, G, B color controls. - Available in PC/DVI Mode Only. R-Gain G-Gain B-Gain - MENU → ▼ → ＋ → ▼ → ＋ → → -+▼▼ → MENU If you adjust picture by using Color Control function, Color Tone will turn to the Custom mode. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitter and shimmer. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again.
Available Mode : PC / DVI : TV : AV : S-Video : Component : HDMI The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Mode The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie", and "Custom") that are preset at the factory. You can activate either Dynamic, Standard, Movie, or Custom.
Digital NR Digital Noise Reduction. If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. Off / Low / Medium / High / Auto →▼→ → ▼▼ → - MENU → ▼ → Film Mode The Film Mode feature offers you a theater-quality viewing experience. In Component mode, film mode is only available for 480i and 576i input.
Balance : Allows you to adjust the sound balance between the left and right speakers. You can hear the sound even when the sound value is set to 0. - MENU → ▼ → ＋ → ▼ → ＋ → → -+▼▼ → MENU Auto Volume Reduces the differences in volume level among broadcasters. Off / On - MENU → ▼ → ＋ → ▼ → ＋ → ▼▼ → Internal Mute If you set this menu "On", sound output from the speakers is muted in case of using the home theater.
Menu Description Antenna You can select a normal or wired channel. If the antenna is connected to ANT 1 IN (AIR),select "Air" and if it is connected to ANT 2 IN(CABLE), select "Cable". If both ANT 1 IN (AIR) and ANT 2 IN (CABLE) are connected, select the antenna input you want. If the antenna input is not selected properly, noise may appear on the screen. The direct button on the remote control is 'ANTENNA' button.
Available Mode : TV : PC / DVI : AV : S-Video : Component : HDMI The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Language Description Play/Stop You can choose one of 3 languages. The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
Analog TV Caption Off / On Channel Mode Caption / Text Field Channel 1 /2 Caption Field 1 /2 Caption Mode DTV Caption Off / On Caption Options Size Caption Mode Default / Service1 ~6 / CC1~4 / Text1~4 Caption Options Size : Default, Small, Standard, Large Font Style : Default, Style0, Style1, Style2, Style3, Style4, Style5, Style6, Style7 Foreground Color : Default, White, Black, Red, Green , Blue, Yellow, Magenta. Cyan Background Color : Default, White, Black, Red, Green , Blue, Yellow, Magenta.
Model SyncMaster 2280HD Self-Test Feature Check Check the following items yourself before calling for service. Contact the service center for problems that you cannot solve by yourself. Self-Test Feature Check | Not Optimum Mode | Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
supported by the monitor. 3. Maintenance and Cleaning 1. Maintaining the Monitor Case. Clean with a soft cloth after disconnecting the power cord. z z Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend a Samsung cleansing agent is used to prevent damage to the screen. 2. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. z z Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.
TV signal is not received z Select "Auto Program" to configure the channel system automatically. (Refer to the Auto Program) 2. Problems related to Screen Problems related to the monitor screen and their solutions are listed. Problems Solutions Screen is blank and power indicator is off z "Check Signal Cable" message z z "Not Optimum Mode" message z z Picture rolls vertically. z Image is not clear. Picture is blurred. z z z Picture image is unstable and vibrates.
No sound z z The sound level is too low. z Check the volume level. (Refer to the Volume) If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. z Adjust the Treble and Bass to appropriate level. z Sound is too high pitched or too low pitched Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card.
For example, while watching a sports game, you can view various data on your favorite player or you can view all or selected screens which have been captured from different angles for a specific scene. In addition, you can retrive information on a previous story or drama or you can buy home shopping products such as an accessory currently on TV. Digital TV broadcasting allows you to easily access various information services in your home creating a more information-oriented home.
Model General General Model Name SyncMaster 2280HD LCD Panel Size 22" Wide diagonal (55 cm) Display area 473.76 mm(H) x 296.1 mm(V) Pixel Pitch 0.282 mm(H) x 0.282 mm(V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1680 x 1050 @ 60 Hz < Analog/Digital > Maximum resolution 1680 x 1050 @ 60 Hz < Analog/Digital > Input Signal, Terminated RGB Analog TTL level (V high ≥ 2.0V, V low ≤ 0.8V) 0.
0.0 X 439.0 X 201.9 mm / 20.5 x 17.3 x 7.9 inch / 7.1 kg / 15.65 lbs (With Stand) 520.0 X 386.0 X 65.5 mm / 20.5 x 15.2 x 2.6 inch (Without Stand) VESA Mounting Interface 100 mm X 100 mm Environmental considerations Operating Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% to 80%, Non-condensing Storage Temperature: -4 °F ~113 °F(-20 °C ~ 45 °C) Humidity: 5% to 95%, Non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.
Model SyncMaster 2280HD Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805-121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.
TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) 8000-4726 http://www.samsung.com/mea Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals.
country regardless of the location of the viewer. Sound Balance Balances the levels of the sound coming from each speaker in televisions with two speakers. Cable TV Whereas the terrestrial broadcasting is delivered via frequency signals through the air, cable broadcasting is transmitted via a cable network. In order to view cable TV, one must purchase a cable receiver and hook it up to the cable network.
organization that has been organized to promote its development and management. EIAJ Electronic Industries Association of Japan. DVI DVI is the acronym for Digital Video Interface. It is a new type of video interface technology that provides the maximum screen quality for high quality display devices and high-end graphics cards including flat panel LCD monitors.
This screen is shown when scenes are captured using digital broadcasting equipment and they are sent in HDTV (16:9) mode. This screen is shown when scenes are converted to analog broadcasting signals before being sent. Humans and objects appear heavier than in reality. This screen is shown when scenes created via analog signals are displayed while watching HDTV broadcasting. If temporary stops, mosaic screens, or jagged screens occur, this is not a TV problem.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
