SyncMaster 225MW SyncMaster 225MW Install Driver
Model SyncMaster 225MW Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.
Do not use a damaged or loose plug. z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. z Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or the person carrying it.
z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes.
Do not spray water or detergent directly onto the monitor. z This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. z z This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center . z The monitor may malfunction, causing electric shock or fire.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.
When not using the product for an extended period of time, keep the product unplugged. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. z Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
z Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
Model SyncMaster 225MW Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
D-Sub Cable Audio Cable Power Cord Remote Control Batteries (AAA X 2) Cleaning Cloth TV Antenna Cable (Coaxial Cable) RCA Cable (Video-Yellow, Audio-Red and White) Component(PR, PB, Y) Cable S-VIDEO Cable Earphones/Headphones SCART Cable DVI Cable DVI to HDMI cable HDMI Cable Other Sold separately RCA to stereo (for PC) cable
Front 1. AUTO 2. PIP 3. 4. - + 5. MENU 6. 7. Remote Control Sensor 8. [ ] Power button 9. Power indicator 10. Speaker 1. AUTO (Available in PC mode only) When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Press to self-adjust to the incoming Analog signal. The values of fine,coarse and position are adjusted automatically. 2. PIP - Available in PC/DVI Mode In PC mode, turns on Video or TV screens in PIP mode. 3.
Rear (The configuration at the back of the monitor may vary from product to product.) 1. POWER z 2. Power terminal Connect the power cord for your monitor to the POWER on the back of the monitor. This product may be used with 100 ~ 240VAC(+/10%). DVI/PC IN / HDMI/PC/DVI-D AUDIO IN 1. PC : Connect the signal cable to the PC port on the back of your monitor. 2. DVI-D : Connect the DVI cable to the DVI-D port on the back of your monitor. 3.
4. ANT IN z 5. HDMI IN z 6. Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the monitor. Make sure to use a TV antenna cable (sold separately) as the antenna cable. Connect the HDMI IN terminal at the back of your monitor to the HDMI terminal of your digital output device using a HDMI cable. EXT(RGB) z Connect the EXT (RGB) port of the monitor to the DVD Player using a SCART jack. As for EXT(RGB) port of the monitor, it makes TV or Video signal input and output.
8. z 9. The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. S-VIDEO / VIDEO / R - AUDIO - L 1. S-VIDEO / VIDEO : Input devices such as DVD, VCR or Camcorder are connected to the VIDEO or S-VIDEO terminal of the monitor using the Video or S-Video cable. 2.
Remote Control The performance of the remote control may be affected by a TV or other electronic device operated near the monitor, causing malfunction due to interference with frequency. 1. POWER 2. Number button 3. -/-- 4. 5. MENU 6. MUTE 7. Up-Down Left-Right buttons 8. ENTER 9. INFO 10. SOURCE 11. PRE-CH 12. P 13. EXIT 14. P.MODE, M/B (MagicBright™) 15. S.MODE 16. STILL 17. P.SIZE 18. SOURCE 19. TTX/MIX 20. DUAL I-II 21. SLEEP 22. PIP 23. AUTO 1.
6. MUTE Press to mute the sound temporarily. Displayed on the bottom left of the screen. Press the MUTE button again to cancel the Mute function. Alternatively press the buttons to cancel the Mute function. 7. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 8. ENTER Activates a highlighted menu item. 9. INFO Current picture information is displayed on the upper left corner of the screen. 10.
21. SLEEP Turns the monitor off after a pre-determined period of time. 22. PIP - Available in PC/DVI Mode Push the PIP button to turn PIP screen On/Off. 23. AUTO - Available In PC mode Only Adjusts the screen display automatically.
Model SyncMaster 225MW Connecting the monitor 1.Connecting to a Computer 1. Connect the power cord for your monitor to the POWER on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Use appropriate connection for your computer. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the PC port on the back of your monitor. [PC] 2-2. Using the DVI (Digital) connector on the video card.
1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the D-SUB port on the Macintosh computer. [D-SUB] 2. Turn on the monitor and Macintosh. Connecting to Other devices This monitor allows the user to connect it to such input devices as a DVD player, a VCR or camcorder, or a DTV or TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. 1-1.
1-2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART. Connect to the DVD Devices input if the device has a EXT (RGB) jack. You can watch DVD simply by hooking up the DVD player with the monitor as long as the power is on. 1. Connect the EXT (RGB) port of the monitor to the DVD Player using a SCART jack. 2. Select Ext. by using the SOURCE. 2.
3. Connecting DVD/DTV Set Top Box Connect to the DVD/DTVSet Top Box input if the device has a DVD/DTV connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on. 1. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the R-AUDIO-L port of the monitor. 2. Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the PR, PB,Y input ports using a component video cable (PR, PB,Y). 3. Select Component using the SOURCE. 4-1.
1. Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the monitor using a DVI to HDMI cable. 2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the HDMI / PC / DVID AUDIO IN terminal of the monitor. 3. Then, start the DVD with a DVD disc inserted. 4. Select HDMI using the SOURCE button. 5.
1. Folding the base The monitor may be reclined from -1 to 23 degrees. 2. Attaching a base This monitor accepts a 100 mm X 100 mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Turn the fixing screw handle on the stand counterclockwise to loosen it and then separate it from the stand. 4.
Installing the monitor driver (Automatic) When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung.com/ (WorldWide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.
z Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) Microsoft® Windows Vista™ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization". 3. Click "Personalization" and then "Display Settings". 4. Click "Advanced Settings…". 5. Click "Properties" in the "Monitor" tab.
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ 6. Click "Update Driver…" in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". 9.
10. Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor Homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced..". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
Model SyncMaster 225MW Input Available Mode : PC / DVI : TV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description SOURCE List Use to select PC, TV, or other external input SOURCEs connected to the Monitor. Use to select the screen of your choice. - The direct button on the remote control is the 'SOURCE' button.
8) HDMI PIP When external AV devices such as VCRs or DVDs are connected to the monitor, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off / On) - Available in PC / DVI Mode Only 1) PIP : Turn the PIP Screen on or off. The direct button on the remote control is 'PIP' button. Off / On 2) SOURCE : Select the input SOURCE for the PIP. The direct button on the remote control is 'SOURCE' button.
Available Mode : PC / DVI : TV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Text, Internet, Entertain and Custom.
Auto Adjustment The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, auto function is performed. - The direct button on the remote control is the 'AUTO' button. - Available in PC Mode Only Size You can switch the Size. 1) Wide 2) 4:3 PIP Picture You can adjust the PIP Screen Settings. - Available in PC / DVI Mode Only 1) Contrast : Adjusts the Contrast of the PIP window on the screen.
1) Dynamic 2) Standard 3) Movie 4) Custom Custom You can use the on-screen menus to change the contrast and brightness according to personal preference. 1) Contrast : Adjusts the contrast. 2) Brightness : Adjusts the brightness. 3) Sharpness : Adjusts the picture sharpness. 4) Colour : Adjusts the picture colour. 5) Tint : Adds a natural tone to the display. The Tint is connected by switching to NTSC from PAL broadcasting and is displayed on the menu while watching.
Available Mode : PC / DVI : TV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description Mode The Monitor has a built-in high fidelity stereo amplifier. The direct button on the remote control is 'S.MODE' button. 1) Standard : Choose Standard for the standard factory settings. 2) Music : Choose Music when watching music videos or concerts.
Channel Available Mode : PC / DVI : TV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description Country Select the country in which the product is being used before you use the Auto Store feature. If you do not see your country in the list, select Others.
Sort It's used to exchange the numbers of two channels. Name If channel name information is broadcast when you store the channels either manually or automatically, the names are assigned to the channels directly. You can however change these names or assign new names as required. Fine Tune Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. Setup Available Mode : PC / DVI : TV : Ext.
Off On Reset Picture parameters are replaced with the factory default values. 1) Image Reset 2) Colour Reset HDMI Black Level When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected. In this case, adjust the screen quality of your TV by configuring the HDMI black level.
Model SyncMaster 225MW Self-Test Feature Check Check the following items yourself before calling for service. Contact the service center for problems that you cannot solve by yourself. Self-Test Feature Check | Not Optimum Mode | Display Adapter Driver Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
supported by the monitor. 3. Display Adapter Driver Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot install the monitor driver. 1. Checking Adapter Driver Click Start Settings Control Panel Display Settings Advanced Adapter. If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly installed.
Installation | Screen | Audio | Remote Control 1. Problems related to Installation Problems related to the monitor installation and their solutions are listed. Problems PC Mode TV Mode Solutions It appears the PC does not function normally. z The monitor screen flickers. z TV screen is blurred or shows noise signals. z TV signal is not received z Check if the Display Adapter Driver (VGA Driver) is properly installed.
Power Indicator blinks green. z Screen is blank and power indicator light is steady green or blinks every 0.5 or 1 seconds z The screen is blank and is blinking. z z The monitor is currently saving the changes made in settings to the OSD memory. The monitor is using its power management system.
function? z How can I clean the outer case/LCD Panel? Set the resolution in the Control Panel→Appearance and Themes→Display→Screen Saver . Set the function in the BIOS-SETUP of the computer. (Refer to Windows/Computer Manual). Windows ME/2000 : Set the resolution in the Control Panel→Display→Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to Windows/Computer Manual).
Model General General Model Name SyncMaster 225MW LCD Panel Size 22" Wide diagonal (55 cm) Display area 473.76 mm(H) x 296.1 mm(V) Pixel Pitch 0.282 mm(H) x 0.282 mm(V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1680 x 1050 @ 60 Hz < Analog/Digital > Maximum resolution 1680 x 1050 @ 60 Hz < Analog/Digital > Input Signal, Terminated RGB Analog TTL level (V high ≥ 2.0V, V low ≤ 0.8V) 0.7 Vp-p 5% Maximum Pixel Clock 146.
520.0 X 439.0 X 201.9 mm / 20.5 X 17.3 X 7.9 inch / 7.3 kg / 16.09 lbs (With Stand) 520.0 X 386.0 X 65.5 mm / 20.5 X 15.2 X 2.6 inch (Without Stand) VESA Mounting Interface 100 mm X 100 mm Environmental considerations Operating Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% to 80%, Non-condensing Storage Temperature: -4 °F ~113 °F(-20 °C ~ 45 °C) Humidity: 5% to 95%, Non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
(kHz) (Hz) (MHz) (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC,1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.
Model SyncMaster 225MW Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805-121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.
TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) 8000-4726 http://www.samsung.com/mea Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals.
country regardless of the location of the viewer. Sound Balance Balances the levels of the sound coming from each speaker in televisions with two speakers. Cable TV Whereas the terrestrial broadcasting is delivered via frequency signals through the air, cable broadcasting is transmitted via a cable network. In order to view cable TV, one must purchase a cable receiver and hook it up to the cable network.
organization that has been organized to promote its development and management. EIAJ Electronic Industries Association of Japan. For Better Display 1. Adjust the computer resolution and screen inection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. { { Resolution: 1680 x 1050 Vertical frequency (refresh rate): 60 Hz 2.
MÉXICO IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V. Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
