SyncMaster 225MD SyncMaster 225MD Install Driver
Model SyncMaster 225MD Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode.
Do not use a damaged or loose plug. z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. (Class l Equipment only.) Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. z Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor.
z Any increase in the internal temperature may cause fire. Put down the monitor carefully. z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly onto the monitor. z This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center. z This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. z z This may cause a malfunction, electric shock or fire.
Never insert anything metallic into the monitor openings. z This may cause electric shock, fire or injury. Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
Place the product out of children's reach, as they could damage by hanging onto it. z A falling product may cause injury to the person or even fatality. When not using the product for an extended period of time, keep the product unplugged. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product.
height so that the top of the monitor is slightly below eye level. z Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. z Keep your arms level with the back of your hands. z Keep the angle of the elbow perpendicular. z Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
Model SyncMaster 225MD Features Features of Digital Broadcasting - All multimedia broadcasting processes including program creation, transmission, and receiving are processed digitally, which allows users to enjoy a very high screen quality without any signal loss as well as benefit from various additional services.
Without Stand With Stand Manual Quick Setup Guide Warranty Card (Not available in all locations) D-Sub Cable Stereo Cable Power Cord Remote Control Batteries (AAA X 2) Cleaning Cloth User's Guide, Monitor Driver Cable Other Sold separately
TV Antenna Cable (Coaxial Cable) RCA Cable (Video-Yellow, Audio-Red and White) Component(PR, PB, Y) Cable S-VIDEO Cable Earphones/Headphones SCART Cable DVI Cable DVI to HDMI cable HDMI Cable RCA to stereo (for PC) cable Digital audio optical output cable This is an accessory that can be added depending on the model. Front 1. TV/DTV 2. PIP 3. ▼, ▲ 4. -, + 5. MENU 6. 7. Remote Control Sensor 8. [ ] Power button 9. Power indicator 10.
1. TV/DTV This button is used to switch between normal and DTV broadcasting signals. [TV] → [DTV] >>Click here to see an animation clip 2. PIP - Available in PC/DVI Mode In PC mode, turns on Video or TV screens in PIP mode. 3. ▼, ▲ Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects TV channels. 4. -, + Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. 5.
Rear (The configuration at the back of the monitor may vary from product to product.) 1. POWER z 2. Connect the power cord for your monitor to the POWER on the back of the monitor. This product may be used with 100 ~ 240VAC(+/10%). DVI/PC IN / HDMI/PC/DVI-D AUDIO IN 1. PC : Connect the signal cable to the PC port on the back of your monitor. 2. DVI-D : Connect the DVI cable to the DVI-D port on the back of your monitor. 3.
4. ANT IN z 5. Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the monitor. Make sure to use a TV antenna cable (sold separately) as the antenna cable. HDMI IN / DIGITAL AUDIO OUT(OPTICAL) 1. HDMI IN : Connect the HDMI IN terminal at the back of your monitor to the HDMI terminal of your digital output device using a HDMI cable. 2.
8. z 9. The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. COMMON INTERFACE z This contains information on CAM inserted in the CI slot and displays it. The Application Info inserting is about the CI CARD. You can install the CAM anytime whether the TV is ON or OFF. 10. S-VIDEO / VIDEO / R - AUDIO - L 1.
Remote Control The performance of the remote control may be affected by a TV or other electronic device operated near the monitor, causing malfunction due to interference with frequency. 1. POWER 2. Number button 3. -/-- 4. TV/DTV 5. CH LIST 6. 7. MENU 8. MUTE 9. Up-Down Left-Right buttons 10. ENTER 11. RETURN 12. SOURCE 13. PRE-CH 14. GUIDE 15. D.MENU 16. P 17. EXIT 18. INFO 19. TTX/MIX 20. COLOR BUTTONS 21. P.MODE, M/B (MagicBright™) 22. S.MODE 23. AUTO 24. P.SIZE 25.
5. CH LIST It display "Channel List" on the screen. 6. Adjusts the audio volume. 7. MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. 8. MUTE Press to mute the sound temporarily. Displayed on the bottom left of the screen. Press the MUTE button again to cancel the Mute function. Alternatively press the buttons to cancel the Mute function. 9. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 10.
Then press the button again to circle through available preconfigured modes. ( Dynamic → Standard → Movie → Custom ) PC / DVI Mode : M/B ( MagicBright™ ) MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes. ( Entertain→ Internet → Text → Custom ) 22. S.MODE When you press this button, current mode is displayed on the lower center of the screen.
Model SyncMaster 225MD Connecting the monitor 1.Connecting to a Computer 1. Connect the power cord for your monitor to the POWER on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Use appropriate connection for your computer. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the PC port on the back of your monitor. [PC] 2-2. Using the DVI (Digital) connector on the video card.
1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the D-SUB port on the Macintosh computer. [PC] 2. Turn on the monitor and Macintosh. Connecting to Other devices This monitor allows the user to connect it to such input devices as a DVD player, a VCR or camcorder, or a DTV or TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product.
2. Connect the the AUDIO OUT port of DVD/VCR/Camcoder to the R-AUDIO-L port of the monitor. 3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. 4. Select AV or S-Video using the SOURCE. 2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART. Connect to the DVD Devices input if the device has a EXT (RGB) jack. You can watch DVD simply by hooking up the DVD player with the monitor as long as the power is on. 1.
3. Select TV using the TV/DTV. 4. Select a desired TV channel. Is weak signal causing poor reception? Purchase and install a signal amplifier for better reception. 4. Connecting DVD/DTV Set Top Box Connect to the DVD/DTVSet Top Box input if the device has a DVD/DTV connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on. 1. Connect the the AUDIO OUT port of DVD / DTV Set-Top Box to the R-AUDIO-L port of the monitor. 2.
HDMI cable. 2. Then, start the DVD with a DVD disc inserted. 3. Select HDMI using the SOURCE button. 6. Connecting Using a DVI to HDMI Cable 1. Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the monitor using a DVI to HDMI cable. 2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the HDMI / PC / DVID AUDIO IN terminal of the monitor. 3.
2. Set the Internal Mute On in the Sound menu using the MENU button. 3. Adjust the sound volume using the Volume button of your amplifier 4. If the connections are set up, power up your monitor and amplifier. Because no sound is emitted from the monitor, you need to use an amplifier. For information on how to connect a speaker and amplifier, refer to the respective user manuals provided by their manufacturers. 8. Connecting COMMON INTERFACE You can install the CAM anytime whether the TV is ON or OFF.
1. Connect your headphones to the Headphone connection terminal. Using the Stand This monitor supports various types of VESA-standard bases. You need to either fold or remove the base in use in order to install a VESA base. 1. Folding the base The monitor may be reclined from -1 to 23 degrees. 2. Attaching a base This monitor accepts a 100 mm X 100 mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2.
z z z z z z z Do not use screws longer than the standard dimension, as they may damage the inside of the Monitor. For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications. Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage. http://www.samsung.com/ 5. Monitor driver installation is completed. Installing the monitor driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor.
5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message “Windows needs…” is displayed, as shown in the figure below, click "Continue". This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 6. Click "Update Driver…" in the "Driver" tab. 7.
8. Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor Homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. 2. 3. 4. 5. 6. 7. 8. 9. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor.
Model SyncMaster 225MD Input Available Mode : PC / DVI : TV : DTV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description Source List Use to select PC, TV, or other external input SOURCEs connected to the Monitor. Use to select the screen of your choice. - The direct button on the remote control is the 'SOURCE' button.
7) Component 8) HDMI 9) DTV PIP When external AV devices such as VCRs or DVDs are connected to the monitor, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off / On) - Available in PC / DVI Mode Only 1) PIP : Turn the PIP Screen on or off. - The direct button on the remote control is 'PIP' button. Off On 2) Source : Select the input SOURCE for the PIP. - The direct button on the remote control is 'SOURCE' button. PC / DVI : TV / Ext.
Available Mode : PC / DVI : TV : DTV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Text, Internet, Entertain and Custom.
4) Custom Adjusts the individual R, G, B Colour Controls. 1) R-Gain 2) G-Gain 3) B-Gain Colour Control If you adjust picture by using Colour Control function, Colour Tone will turn to the Custom mode. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitter and shimmer. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again.
Available Mode : PC / DVI : TV : DTV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description Mode The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie", and "Custom") that are preset at the factory. You can activate either Dynamic, Standard, Movie, or Custom.
2) 16:9 3) Zoom1 4) Zoom2 5) 4:3 Digital NR - Digital Noise Reduction. You can turn the Noise Elimination feature Off / Low / Medium / High / Auto. The Digital Noise Elimination feature allows you to enjoy clearer and crisper images. 1) Off 2) Low 3) Medium 4) High 5) Auto Film Mode You can turn Film Mode Off / On. The Film Mode feature offers you a theater-quality viewing experience. - This function supports the resolution only up to 480i/576i when the input mode is Component or HDMI.
: Choose Music when watching music videos or concerts. 3) Movie : Choose Movie when viewing movies. 4) Speech : Choose Speech when watching a show that is mostly dialogue (i.e., news). 5) Custom : Choose Custom if you want to adjust the settings according to personal preference. Custom The sound settings can be adjusted to suit your personal preference. 1) Bass : Emphasize low frequency audio. 2) Treble : Emphasize high frequency audio.
Available Mode : PC / DVI : TV : DTV : Ext. : AV : S-Video : Component : HDMI The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Description Country Select the country in which the product is being used before you use the Auto Store feature. If you do not see your country in the list, select Others.
blocking certain broadcast or video programs. The Child Lock feature can be selected only from the remote. Sort It's used to exchange the numbers of two channels. Name If channel name information is broadcast when you store the channels either manually or automatically, the names are assigned to the channels directly. You can however change these names or assign new names as required. Fine Tune Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly.
Transparency 1) High 2) Medium 3) Low 4) Opaque Blue Screen If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the "Blue screen" mode to "Off". Off On HDMI Black Level When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc.
| Starting | Channel | Guide | Setup | Language The company does not guarantee the normal operation of the DTV menu for countries other than the 6 supported countries (United Kingdom, Germany, France, Italy, Spain, Austria) because only these country standards are supported. In addition, when the country of the broadcast stream differs from the country selected by the current user, the string appearing in the channel banner, Info, Guide, Channel Manager, etc. may not be displayed properly.
| | Starting Channel | Guide | Setup | Language | Auto Store / Manual Store / Edit Favourite Channels / Channel List ◈ Updating the Channel List Automatically You can update the channel list when the broadcaster adds new Services or if you move the TV to a new location. 1. Press the D.MENU button to display the DTV menu. 2. Press the or ENTER button. button to select "Channel", then press the 3. Press the ENTER button again, to select "Auto Store". Press the ENTER button. 4.
6. Press the EXIT button to exit. - Add You can use this function when one or more favourite channels have been selected. 1. Press the D.MENU button to display the DTV menu. 2. Press the button. or button to select "Channel", then press the ENTER 3. Press the or button to select "Edit Favourite Channels", then press the ENTER button. 4. Press the red button in the "Edit Favourite Channels" menu. To add more channels, refer to the step 5 on the previous description. 5.
◈ Selecting Channel List You can exclude the channels you have chosen from the channels you have scanned.When you scan through the stored channels, those you have chosen to skip are not displayed. All channels that you do not specifically choose to skip are displayed during scanning. 1. Press the D.MENU button to display the DTV menu. 2. Press the or button to select "Channel", then press the ENTER button. 3. Press the or button to select "Channel List". Press the ENTER button. 4. Press the "Default".
While viewing a channel, additional information about the current programme may be displayed. 1. While viewing a programme, press the INFO button The programme information is displayed. 2. To exit from banner information, press the INFO button.
| | Starting | Channel | Guide Setup | Language | Now & Next Guide / Full Guide / Scheduled List / Default Guide ◈ Viewing the EPG (Electronic Programme Guide) Information The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information becomes available.
Teletext, Languages of Subtitle or Teletext, and brief summary of the highlighted programme are included on the detailed information. "..." will be appeared if the summary is long. Six channels are displayed. To scroll between channels, move to a channel using the page, use the P or or button. To display page by button.
1. Press the D.MENU button to display the DTV menu. 2. Press the ENTER button again, to select "Guide". 3. Select the your required guide ("Now & Next Guide" or "Full Guide") by pressing the 4. Press the ENTER button. or button. 5. Press the green button. All the channel lists and the favorite channel lists will be toggled. 6. Select a programme of your choice by pressing the ; , , , or button. 7. Press the INFO button to display information about the highlighted programme. 8.
| | Starting Channel | Guide | Setup | Language | Menu Transparency / Parental Lock / Subtitle / Subtitle Mode / Audio Format / Digital Text / Time Zone / System ◈ Adjusting the Menu Translucency You can set the translucency of the menu. 1. Press the D.MENU button to display the DTV menu. 2. Press the or 3. Press the or ENTER button. button to select "Setup", then press the ENTER button. button to select "Menu Transparency" then press the 4.
1. Press the D.MENU button to display the DTV menu. 2. Press the 3. Press the button. or button to select "Setup", then press the ENTER button. or button to select "Subtitle ", then press the ENTER 4. Select "On" by pressing the or 5. Press the EXIT button to exit. button. Press the ENTER button. ◈ Setting the Subtitle Mode Use this menu to set the Subtitle Mode. "Normal" under the menu is the basic subtitle and "Hard of hearing" is the subtitle for a hearing-impaired person. 1. Press the D.
◈ Selecting the Time Zone (Spain only) Select the time zone where locate 1. Press the D.MENU button to display the DTV menu. 2. Press the 3. Press the button. or button to select "Setup", then press the ENTER button. or button to select "Time Zone", then press the ENTER 4. Select the time zone where you locate by pressing the Press the ENTER button. or button. The following options are available The Iberian Peninsula and Balears Islands - Canarian Islands 5. Press the EXIT button to exit.
Press the ENTER button, then the current software version is shown. To display the software version information, press the ENTER button again. - Manual Upgrade Press the ENTER button to search for new software from the currently broadcasting channels. - Standby Mode Upgrade : On / Off Press the ENTER button. To continue software upgrade with master power on, Select On by pressing the or button. 45 minutes after entering standby mode, a manual upgrade is automatically conducted.
2. Press the 3. Press the button. or button to select "Setup", then press the ENTER button. or button to select "System", then press the ENTER 4. Press the or ENTER button button to select "Common Interface", then press the 5. Select to "CI Menu" by pressing the button. or 6. Select the required option by pressing the ENTER button. button, and press the ENTER or button, and press the 7. Press the EXIT button to exit. Select the CI Menu based on the menu PC Card.
| | Starting Channel | Guide | Setup | Language | Audio Language / Subtitle Language / Teletext Language / Preference ◈ Selecting the Preferred Language (Audio, Subtitle or Teletext) You can change the default value for subtitle, audio teletext languages. Displays the language information for the incoming stream. 1. Press the D.MENU button to display the DTV menu. 2. Press the button. or button to select "Language", then press the ENTER 3.
Model SyncMaster 225MD Self-Test Feature Check Check the following items yourself before calling for service. Contact the service center for problems that you cannot solve by yourself. Self-Test Feature Check | Not Optimum Mode | Display Adapter Driver Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are supported by the monitor. 3. Display Adapter Driver Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot install the monitor driver. 1. Checking Adapter Driver Click Start Settings Control Panel Display Settings Advanced Adapter.
the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Installation | Screen | Audio | Remote Control 1. Problems related to Installation Problems related to the monitor installation and their solutions are listed. Problems PC Mode TV Mode Solutions It appears the PC does not function normally. z The monitor screen flickers.
dark shadows. White color is poor. Power Indicator blinks green. z Screen is blank and power indicator light is steady green or blinks every 0.5 or 1 seconds z The screen is blank and is blinking. z z The monitor is currently saving the changes made in settings to the OSD memory. The monitor is using its power management system.
* Contact the video card manufacturer for details. How can I set the Power Saving function? z z How can I clean the outer case/LCD Panel? Windows XP : Set the resolution in the Control Panel→Appearance and Themes→Display→Screen Saver . Set the function in the BIOS-SETUP of the computer. (Refer to Windows/Computer Manual). Windows ME/2000 : Set the resolution in the Control Panel→Display→Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to Windows/Computer Manual).
Model General General Model Name SyncMaster 225MD LCD Panel Size 22" Wide diagonal (55 cm) Display area 473.76 mm(H) x 296.1 mm(V) Pixel Pitch 0.282 mm(H) x 0.282 mm(V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7 M Resolution Optimum resolution 1680 x 1050 @ 60 Hz Maximum resolution 1680 x 1050 @ 60 Hz Input Signal, Terminated RGB Analog TTL level (V high ≥ 2.0V, V low ≤ 0.8V) 0.
520.0 X 439.0 X 201.9 mm / 20.5 X 17.3 X 7.9 inch / 7.1 kg / 15.7 lbs (With Stand) 520.0 X 386.0 X 65.5 mm / 20.5 X 15.2 X 2.6 inch (Without Stand) VESA Mounting Interface 100 mm X 100 mm Environmental considerations Operating Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% to 80%, Non-condensing Storage Temperature: -4 °F ~113 °F(-20 °C ~ 45 °C) Humidity: 5% to 95%, Non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Input Source Supported Systems AV(CVBS) NTSC-3.58, NTSC-4.43, PAL 60, PAL, SECAM S-VIDEO NTSC-3.58, NTSC-4.43, PAL 60, PAL, SECAM EXT TV(Analog) DTV NTSC-3.58, NTSC-4.
Model SyncMaster 225MD Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805-121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.
TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) 8000-4726 http://www.samsung.com/mea Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals.
country regardless of the location of the viewer. Sound Balance Balances the levels of the sound coming from each speaker in televisions with two speakers. Cable TV Whereas the terrestrial broadcasting is delivered via frequency signals through the air, cable broadcasting is transmitted via a cable network. In order to view cable TV, one must purchase a cable receiver and hook it up to the cable network.
organization that has been organized to promote its development and management. EIAJ Electronic Industries Association of Japan. DVI DVI is the acronym for Digital Video Interface. It is a new type of video interface technology that provides the maximum screen quality for high quality display devices and high-end graphics cards including flat panel LCD monitors.
This screen is shown when scenes are captured using digital broadcasting equipment and they are sent in HDTV (16:9) mode. This screen is shown when scenes are converted to analog broadcasting signals before being sent. Humans and objects appear heavier than in reality. This screen is shown when scenes created via analog signals are displayed while watching HDTV broadcasting. If temporary stops, mosaic screens, or jagged screens occur, this is not a TV problem.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
