SyncMaster 943EW/943EWX/2043EW/2043EWX/2243EW/2243EWX LCD Monitor User Manual Downloaded from ManualMonitor.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the monitor.
Safety Instructions DO NOT PLACE CANDLES,MOSQUITO REPELLANT,CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT. • Otherwise, this may cause fire. Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. Put down the monitor carefully.
Safety Instructions Do not spray cleaner directly onto the surface of the product. • Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off. Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10. When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire.
Safety Instructions Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. • Otherwise, this may result in electric shock or fire. When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. • Otherwise, this may result in electric shock or fire. If thunder or lightening is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire.
Safety Instructions Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. If you continually move closer to the product screen, your eyesight may be failing. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product.
Safety Instructions Do not drop any objects onto the product or cause any impact to the product. • Otherwise, this may result in electric shock or fire. Do not use a humidifier or kitchen table near the product. • Otherwise, this may result in electric shock or fire. When there is a gas leak, do not touch the product or the power plug but ventilate immediately. • If a spark occurs, it may cause an explosion or fire. If the product has been turned on for a long time, the display panel becomes hot.
Safety Instructions Downloaded from ManualMonitor.com Manuals • Adjust the angle so that light is not reflected on the screen. • Place your arms perpendicular to your sides and allow your arms to be level with the back of the hand. • Keep your elbow at 90 degrees. • Keep your knees at greater than 90 degrees, and keep your heels firmly on the floor. Keep your arms lower than your heart.
Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Note MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type2 Monitor & HAS stand Manuals Quick Setup Guide Warranty Card (Not available in all locations) Downloaded from ManualMonitor.
Introduction Cables D-Sub Cable Power Cord DVI Cable (option) Others Cleaning Cloth Note Cleaning Cloth is only provided for highly polished black products as a product feature. Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count.
Introduction Front MENU button [MENU/ ] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Customized Key[ ] You can customize key assignment for the Custom button according to your preferences. Note You can configure the customized key for a required function via Setup > Customized Key. Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness.
Introduction Note If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. >> Click here to see an animation clip AUTO button Use this button for auto adjustment. >> Click here to see an animation clip Power button [ ] Use this button for turning the product on and off. Power Indicator This light is lit when operating normally, and blinks once when your adjustments are saved.
Introduction Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor. Kensington Lock The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. Note The location of the Kensington Lock may be different depending on its model. Using the Anti-Theft Kensington Lock 1.
Connections {943EW/943EWX} Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
Connections {943EW/943EWX} Using the Stand Monitor Assembly Simple Stand HAS Stand Monitor and Bottom HAS Stand A. Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. Downloaded from ManualMonitor.
Connections Simple Stand HAS Stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
Connections {2043EW/2043EWX} Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card.
Connections {2043EW/2043EWX} Using the Stand Monitor Assembly Simple Stand HAS Stand Monitor and Bottom HAS Stand A. Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. Downloaded from ManualMonitor.
Connections Simple Stand HAS Stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
Connections {2243EW/2243EWX} Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card.
Connections {2243EW/2243EWX} Using the Stand Monitor Assembly Simple Stand HAS Stand Monitor and Bottom HAS Stand A. Stand Stopper Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad. Downloaded from ManualMonitor.
Connections Simple Stand HAS Stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CDROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization". 3. Click "Personalization" and then "Display Settings". 4.
Using the Software If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System Downloaded from ManualMonitor.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will..." then click "Next" and then click "Have disk". Downloaded from ManualMonitor.
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button. Microsoft® Windows® Millennium Operating System 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7.
Using the Software 5. Set a Keyboard for your computer. 6. The next screen is for setting your monitor. 7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.) 9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your monitor.
Using the Software How to delete the Natural Color software program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select Natural Color from the list and then click the "Add/Delete" button. MagicTune™ Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file.
Using the Software System Requirements OS • Windows 2000 • Windows XP Home Edition • Windows XP Professional • Windows Vista™ It is recommended using MagicTune™ in Windows® 2000 or later. Hardware • 32 MB Memory above • 60 MB Hard disk space above For more information, visit the MagicTune™ website. Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows® Control Panel. Perform the following steps remove MagicTune™. 1.
Using the Software MagicRotation Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. Note If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MagicRotation executable file on the CD. 3. Select installation Language, Click "Next". 4. When the Installation Shield Wizard window appears, click "Next". 5.
Using the Software • Select the Orientation (90, 180, 270) you want to view the application. • Relaunch the application. In most cases this should fix the problem. 3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the orientation mode selected (90, 180, 270). e.g. 3D games 4. DOS based applications in Full Screen Mode will not function as per the orientation mode selected (90, 180, 270). 5. Dual is not supported in Windows®‚ 98, ME, NT 4.0. 6.
Using the Software 1. Go to [Task Tray] → [Start] → [Settings] and select [Control Panel] in the menu. If the program runs on Windows® XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3. In the "Add or Remove Programs" screen, scroll down to find "MagicRotation." Click on it to highlight it. 4. Click the "Change/Remove" button to remove the program. 5. Click "Yes" to begin the uninstall process. 6.
Using the Software 9. When the installation is complete, the Multiscreen executable icon appears on your desktop. Double-click the icon to start the program. Multiscreen execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installation Problems The installation of MultiScreen can be affected by such factors as the video card, motherboard and the network environment.
Adjusting the Monitor {943EW/943EWX} Direct Functions AUTO When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine, Coarse and Position are adjusted automatically. (Available in Analog mode only) If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy.
Adjusting the Monitor When pressing the MENU button after locking the OSD This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment lock function. Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment lock function. Downloaded from ManualMonitor.
Adjusting the Monitor Note Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust Customized Key ( ) using the Direct button. Customized key You can customize key assignment for the Custom button according to your preferences. To view the operating screen displayed when pressing the [ ] button after configuring the customized key for a function, click the name of each function.
Adjusting the Monitor Brightness When OSD is not on the screen, push the Brightness ( SOURCE Selects the video signal while the OSD is off. Downloaded from ManualMonitor.com Manuals ) button to adjust brightness.
Adjusting the Monitor {943EW/943EWX} OSD Function Picture Brightness Contrast MagicBright Color MagicColor Color Tone Color Con- Color Effect Gamma trol Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Reset Customized Key Off Timer Auto Source Image Size Information Picture Brightness (Not available in MagicBright mode of Dynamic Contrast.
Adjusting the Monitor You can use the on-screen menus to change the contrast according to personal preference. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → → , → → , → MENU MagicBright Push the button to circle through available preconfigured modes. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Cus- Downloaded from ManualMonitor.
Adjusting the Monitor tom, Text, Internet, Game, Sport, Movie and Dynamic Contrast. Each mode has its own pre-configured brightness value. You can easily select one of seven settings by simply pressing Customized Key control button. • Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.
Adjusting the Monitor MagicColor MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. • Off - Returns to the original mode. • Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. • Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Adjusting the Monitor Color Tone The tone of the color can be changed and one of four modes can be selected. • Cool - Makes whites bluish. • Normal - Keeps whites white. • Warm - Makes whites reddish. • Custom - Select this mode when you want to adjust the image according to your preferences. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor Color Control Adjusts individual Red, Green, Blue color balance. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → → , → MENU Color Effect You can change the overall mood by changing the screen colors. ( Not available in MagicColor mode of Full and Intelligent. ) Downloaded from ManualMonitor.
Adjusting the Monitor • Off • Off - This applies an achromatic color to the screen to adjust the screen effects. • Grayscale - The default colors of black and white are displayed. • Green - This applies the green color effect to a black and white screen. • Aqua - This applies the aqua color effect to a black and white screen. • Sepia - This applies the Sepia color effect to a black and white screen.
Adjusting the Monitor Image Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in Analog mode only) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). (Available in Analog mode only) MENU → , → → Sharpness Downloaded from ManualMonitor.
Adjusting the Monitor Changes the clearance of image. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → MENU H-Position Changes the horizontal position of the monitor's entire display. (Available in Analog mode only) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor V-Position Changes the vertical position of the monitor's entire display. (Available in Analog mode only) MENU → , → → , → → OSD Language You can choose one of nine languages. Downloaded from ManualMonitor.
Adjusting the Monitor Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. MENU → , → → → , → MENU H-Position You can change the horizontal position where the OSD menu appears on your monitor. MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor V-Position You can change the vertical position where the OSD menu appears on your monitor. MENU → , → → , → → , → MENU Transparency Change the transparency of the background of the OSD. • Off MENU → • , → On → Downloaded from ManualMonitor.
Adjusting the Monitor Display Time The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off. • 5 sec MENU → • , → 10 sec → Setup Reset Downloaded from ManualMonitor.
Adjusting the Monitor Reverts the product settings to factory defaults. • No MENU → • , → Yes → → , → MENU Customized Key You can specify a function which will be activated when the Customized Key ( MENU → , → → Off Timer Downloaded from ManualMonitor.com Manuals , → → , →MENU )is pressed.
Adjusting the Monitor The monitors will turn off automatically at the specified time. • Off MENU → • , → On → , → → , → → , → MENU Auto Source Select Auto Source for the monitor to automatically select the signal source. • Auto MENU → • , → Manual → Downloaded from ManualMonitor.
Adjusting the Monitor Image Size You can change the size of the screen displayed on your monitor. • Auto • Wide • Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals. • Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals. Note • Signals not available in the standard mode table are not supported.
Adjusting the Monitor Information Shows a video source, display mode on the OSD screen. MENU → , →MENU {2043EW/2043EWX} Direct Functions AUTO When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Downloaded from ManualMonitor.
Adjusting the Monitor Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine, Coarse and Position are adjusted automatically. (Available in Analog mode only) If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy. If you change resolution in the control panel, auto function will be executed automatically.
Adjusting the Monitor This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment lock function. Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment lock function.
Adjusting the Monitor Customized key You can customize key assignment for the Custom button according to your preferences. ] button after configuring the To view the operating screen displayed when pressing the [ customized key for a function, click the name of each function. ( Image Size - MagicBright - MagicColor - Color Effect) Note You can configure the customized key for a required function via Setup > Customized Key. Downloaded from ManualMonitor.
Adjusting the Monitor Brightness When OSD is not on the screen, push the Brightness ( SOURCE Selects the video signal while the OSD is off. Downloaded from ManualMonitor.com Manuals ) button to adjust brightness.
Adjusting the Monitor {2043EW/2043EWX} OSD Function Picture Brightness Contrast MagicBright Color MagicColor Color Tone Color Con- Color Effect Gamma trol Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Reset Customized Key Off Timer Auto Source Image Size Information Picture Brightness (Not available in MagicBright mode of Dynamic Contrast.
Adjusting the Monitor You can use the on-screen menus to change the contrast according to personal preference. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → → , → → , → MENU MagicBright Push the button to circle through available preconfigured modes. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Cus- Downloaded from ManualMonitor.
Adjusting the Monitor tom, Text, Internet, Game, Sport, Movie and Dynamic Contrast. Each mode has its own pre-configured brightness value. You can easily select one of seven settings by simply pressing Customized Key control button. • Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.
Adjusting the Monitor MagicColor MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. • Off - Returns to the original mode. • Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. • Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Adjusting the Monitor Color Tone The tone of the color can be changed and one of four modes can be selected. • Cool - Makes whites bluish. • Normal - Keeps whites white. • Warm - Makes whites reddish. • Custom - Select this mode when you want to adjust the image according to your preferences. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor Color Control Adjusts individual Red, Green, Blue color balance. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → → , → MENU Color Effect You can change the overall mood by changing the screen colors. ( Not available in MagicColor mode of Full and Intelligent. ) Downloaded from ManualMonitor.
Adjusting the Monitor • Off • Off - This applies an achromatic color to the screen to adjust the screen effects. • Grayscale - The default colors of black and white are displayed. • Green - This applies the green color effect to a black and white screen. • Aqua - This applies the aqua color effect to a black and white screen. • Sepia - This applies the Sepia color effect to a black and white screen.
Adjusting the Monitor Image Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in Analog mode only) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). (Available in Analog mode only) MENU → , → → Sharpness Downloaded from ManualMonitor.
Adjusting the Monitor Changes the clearance of image. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → MENU H-Position Changes the horizontal position of the monitor's entire display. (Available in Analog mode only) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor V-Position Changes the vertical position of the monitor's entire display. (Available in Analog mode only) MENU → , → → , → → OSD Language You can choose one of nine languages. Downloaded from ManualMonitor.
Adjusting the Monitor Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. MENU → , → → → , → MENU H-Position You can change the horizontal position where the OSD menu appears on your monitor. MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor V-Position You can change the vertical position where the OSD menu appears on your monitor. MENU → , → → , → → , → MENU Transparency Change the transparency of the background of the OSD. • Off MENU → • , → On → Downloaded from ManualMonitor.
Adjusting the Monitor Display Time The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off. • 5 sec MENU → • , → 10 sec → Setup Reset Downloaded from ManualMonitor.
Adjusting the Monitor Reverts the product settings to factory defaults. • No MENU → • , → Yes → → , → MENU Customized Key You can specify a function which will be activated when the Customized Key ( ed. MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor Off Timer The monitors will turn off automatically at the specified time. • Off MENU → • , → On → , → → , → → , → MENU Auto Source Select Auto Source for the monitor to automatically select the signal source. Downloaded from ManualMonitor.
Adjusting the Monitor • Auto MENU → • , → Manual → , → → , →MENU Image Size You can change the size of the screen displayed on your monitor. • Auto • Wide • Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals. • Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals. Note • Signals not available in the standard mode table are not supported.
Adjusting the Monitor Information Shows a video source, display mode on the OSD screen. MENU → , →MENU {2243EW/2243EWX} Direct Functions AUTO When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Downloaded from ManualMonitor.
Adjusting the Monitor Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine, Coarse and Position are adjusted automatically. (Available in Analog mode only) If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy. If you change resolution in the control panel, auto function will be executed automatically.
Adjusting the Monitor This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment lock function. Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment lock function.
Adjusting the Monitor Customized key You can customize key assignment for the Custom button according to your preferences. ] button after configuring the To view the operating screen displayed when pressing the [ customized key for a function, click the name of each function. ( Image Size - MagicBright - MagicColor - Color Effect) Note You can configure the customized key for a required function via Setup > Customized Key. Downloaded from ManualMonitor.
Adjusting the Monitor Brightness When OSD is not on the screen, push the Brightness ( SOURCE Selects the video signal while the OSD is off. Downloaded from ManualMonitor.com Manuals ) button to adjust brightness.
Adjusting the Monitor {2243EW/2243EWX} OSD Function Picture Brightness Contrast MagicBright Color MagicColor Color Tone Color Con- Color Effect Gamma trol Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Reset Customized Key Off Timer Auto Source Image Size Information Picture Brightness (Not available in MagicBright mode of Dynamic Contrast.
Adjusting the Monitor You can use the on-screen menus to change the contrast according to personal preference. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → → , → → , → MENU MagicBright Push the button to circle through available preconfigured modes. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Cus- Downloaded from ManualMonitor.
Adjusting the Monitor tom, Text, Internet, Game, Sport, Movie and Dynamic Contrast. Each mode has its own pre-configured brightness value. You can easily select one of seven settings by simply pressing Customized Key control button. • Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.
Adjusting the Monitor MagicColor MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. • Off - Returns to the original mode. • Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. • Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Adjusting the Monitor Color Tone The tone of the color can be changed and one of four modes can be selected. • Cool - Makes whites bluish. • Normal - Keeps whites white. • Warm - Makes whites reddish. • Custom - Select this mode when you want to adjust the image according to your preferences. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor Color Control Adjusts individual Red, Green, Blue color balance. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → → , → MENU Color Effect You can change the overall mood by changing the screen colors. ( Not available in MagicColor mode of Full and Intelligent. ) Downloaded from ManualMonitor.
Adjusting the Monitor • Off • Off - This applies an achromatic color to the screen to adjust the screen effects. • Grayscale - The default colors of black and white are displayed. • Green - This applies the green color effect to a black and white screen. • Aqua - This applies the aqua color effect to a black and white screen. • Sepia - This applies the Sepia color effect to a black and white screen.
Adjusting the Monitor Image Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in Analog mode only) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). (Available in Analog mode only) MENU → , → → Sharpness Downloaded from ManualMonitor.
Adjusting the Monitor Changes the clearance of image. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → MENU H-Position Changes the horizontal position of the monitor's entire display. (Available in Analog mode only) MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor V-Position Changes the vertical position of the monitor's entire display. (Available in Analog mode only) MENU → , → → , → → OSD Language You can choose one of nine languages. Downloaded from ManualMonitor.
Adjusting the Monitor Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. MENU → , → → → , → MENU H-Position You can change the horizontal position where the OSD menu appears on your monitor. MENU → , → → Downloaded from ManualMonitor.
Adjusting the Monitor V-Position You can change the vertical position where the OSD menu appears on your monitor. MENU → , → → , → → , → MENU Transparency Change the transparency of the background of the OSD. • Off MENU → • , → On → Downloaded from ManualMonitor.
Adjusting the Monitor Display Time The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off. • 5 sec MENU → • , → 10 sec → Setup Reset Downloaded from ManualMonitor.
Adjusting the Monitor Reverts the product settings to factory defaults. • No MENU → • , → Yes → → , → MENU Customized Key You can specify a function which will be activated when the Customized Key ( MENU → , → → Off Timer Downloaded from ManualMonitor.com Manuals , → → , →MENU )is pressed.
Adjusting the Monitor The monitors will turn off automatically at the specified time. • Off MENU → • , → On → , → → , → → , → MENU Auto Source Select Auto Source for the monitor to automatically select the signal source. • Auto MENU → • , → Manual → Downloaded from ManualMonitor.
Adjusting the Monitor Image Size You can change the size of the screen displayed on your monitor. • Auto • Wide • Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals. • Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals. Note • Signals not available in the standard mode table are not supported.
Adjusting the Monitor Information Shows a video source, display mode on the OSD screen. MENU → , →MENU Downloaded from ManualMonitor.
Troubleshooting {943EW/943EWX} Self-Test Feature Check Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged.
Troubleshooting Useful Tips A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
Troubleshooting A: You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. A: Adjust the maximum resolution and frequency that the monitor can handle properly. A: If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1440 x 900 60 Hz" message is displayed.
Troubleshooting Q: Have you adjusted the resolution or frequency to the monitor? A: Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes). Q: The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. Q: Have you adjusted the resolution or frequency on the monitor? A: Adjust the resolution and frequency of the video card.
Troubleshooting A: To check whether your PC is available for MagicTune™ feature, follow the steps below (When Windows is XP); Control Panel → Performance and Maintenance → System → Hardware → Device Manager → Monitors → After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. A: MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor.
Troubleshooting A: Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjusts the resolution? A: Windows XP: Set the resolution in the Control Panel → Appearance and Themes → Display → Settings. A: Windows ME/2000: Set the resolution in the Control Panel → Display → Settings. * Contact the video card manufacturer for details.
Troubleshooting If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
Troubleshooting Check List Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. No images on the screen. I cannot turn on the monitor. Q: Is the power cord connected properly? A: Check the power cord connection and supply.
Troubleshooting A: The monitor is in PowerSaver mode. A: Press a key on the keyboard to activate the monitor and restore the image on the screen. A: If there is still no image, press the ' /SOURCE' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
Troubleshooting LED is blinking but no images on the screen. Q: Is the frequency properly adjusted when checking the Display Timing on the menu? A: Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
Troubleshooting A: Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune Q: Did you install the program? A: Reboot the computer after installing the program for the first time. If a copy of the program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program.
Troubleshooting A: Windows XP: Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). A: Windows ME/2000: Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
Troubleshooting Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor.
Troubleshooting (Connected using the DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press ‘ /SOURCE’ button to have the monitor double-check the input signal source.
Troubleshooting The screen shows strange colors or just black and white. Q: Is the screen displaying only one color as if looking at the screen through a cellophane paper? A: Check the signal cable connection. A: Make sure the video card is fully inserted in its slot. Q: Have the screen colors become strange after running a program or due to a crash between applications? A: Reboot the computer.
Troubleshooting Set the resolution at the Control Panel → Display → Settings. Q: Has the video card been set properly? A: Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Q: Have you installed the monitor driver? A: Install the monitor driver according to the Driver Installation Instructions. Q: See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Troubleshooting If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution.
Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Downloaded from ManualMonitor.
Specifications General General Model Name SyncMaster 943EW LCD Panel Size 19 inch (48 cm) Display area 408.24 mm (H) x 255.15 mm (V) Pixel Pitch 0.2835 mm (H) x 0.2835 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Resolution Optimum resolution 1440 x 900@60 Hz Maximum resolution 1440 x 900@75 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ± 5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.
Specifications Dimensions (W x H x D) / Weight (HAS Stand) 439 x 357.3 x 190 mm (17.2 x 14.0 x 7.48 inch) (With Stand)/ 5.0 kg (11.0 lbs) VESA Mounting Interface 75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.
Specifications State Normal Operation Power saving mode Power off (Power button) EPA/ENERGY 2000 Power Consumption 20 watts 1 watts 1 watts This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Specifications Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate.
Specifications Signal Cable DVI-D to DVI-D connector, Detachable Dimensions (W x H x D) / Weight (Simple Stand) 439 x 290x 68.4 mm (17.2 x 11.4 x 2.69 inch) (Without Stand) 439 x 368 x 185 mm (17.2 x 14.4 x 7.48 inch) (With Stand)/ 3.8 kg (8.4 lbs) Dimensions (W x H x D) / Weight (HAS Stand) 439 x 290 x 65.5 mm (17.2 x 11.4 x 2.57 inch) (Without Stand) 439 x 357.3 x 190 mm(17.2 x 14.0 x 7.48 inch) (With Stand)/5.0 kg(11.
Specifications on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) VESA, 1280 X 960 60.000 60.000 108.000 +/+ VESA, 1280 X 1024 63.981 60.020 108.000 +/+ VESA, 1280 X 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1440 x 900 70.635 74.984 136.
Specifications Input Signal, Terminated TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V) Maximum Pixel Clock 146 MHz (Analog, Digital) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable Dimensions (W x H x D) / Weight (Simple Stand) 469.3 x 307.8 x 72.3 mm (18.5 x 12.1 x 2.8 inch) (Without Stand) 469.3 x 393.8 x 217.5 mm (18.5 x 15.5 x 8.6 inch) (With Stand)/5.1 kg (11.
Specifications Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.) PowerSaver This monitor has a built-in power management system called PowerSaver.
Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 X 768 47.776 60.000 79.500 -/+ VESA, 1280 X 768 60.289 74.893 102.250 -/+ VESA, 1280 X 800 49.702 59.810 83.
Specifications Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ± 5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V) Maximum Pixel Clock 146 MHz (Analog, Digital) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable Dimensions (W x H x D) / Weight (Simple Stand) 469.3 x 307.8 x 72.3 mm (18.5 x 12.1 x 2.8 inch) (Without Stand) 469.
Specifications Dot Acceptable For example, the number of TFT-LCD sub pixels contained in this product are 5,292,000. Note Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.
Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 1024 x 768 48.363 60.004 65.
Specifications Display Color 16.7M Resolution Optimum resolution 1680 x 1050@60 Hz Maximum resolution 1680 x 1050@60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ± 5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.
Specifications Plug and Play Capability conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen.
Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.
Specifications LCD Panel Display area 473.76 mm (H) x 296.1 mm (V) Pixel Pitch 0.282 mm (H) x 0.282 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Resolution Optimum resolution 1680 x 1050@60 Hz Maximum resolution 1680 x 1050@60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ± 5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.
Specifications Environmental considerations Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Information {943EW/943EWX} For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFTLCD.
Information During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD, are subject to image retention. This is not a product defect.
Information • Recommended settings: Bright colors with little difference in luminance • Change the characters color and background color every 30 minutes Ex) • Every 30 minutes, change the characters with movement. Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions.
Information Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II Downloaded from ManualMonitor.
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.
Appendix Europe 0825 08 65 65 (€ 0.15/Min) GERMANY 01805 - SAMSUNG (7267864, € http://www.samsung.de 0.14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com/hu ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.com/lu NETHERLANDS 0900 - SAMSUNG (7267864, € http://www.samsung.com/nl 0.10/Min) NORWAY 3-SAMSUNG (7267864) POLAND 0 - 801 - 1SAMSUNG (172678) http://www.samsung.com/pl http://www.samsung.
Appendix Asia Pacific MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800 SAMSUNG(0800 726 786) http://www.samsung.com/nz PHILIPPINES 1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG(726-7864) http://www.samsung.com/sg THAILAND 1800-29-3232 http://www.samsung.com/th 02-689-3232 TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.
Appendix while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.
Appendix Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
