WASHING MACHINE SWF-P8 SWF-P10 SWF-P12 SERVICE WASHING MACHINE Manual CONTENTS 1. SPECIFICATIONS 2. OVERVIEW OF THE WASHING MACHINE 3. OVERVIEW OF THE CONTROL PANEL 4. PROCESS TABLE 5. GENERAL REEOR FUNCTION 6. TROUBLE DIAGNOSIS 7. TEST MODE 8. DESIGNATION OF MAIN COMPONENTS 9. PCB SHEMATIC DIAGRAM PCB CIRCUIT DIAGRAM PCB PATTERN DIAGRAM WIRING DIAGRAM 10.ASSEMBLE AND DISASSEMBLE 11.TOOLS FOR DISASSEMBLY AND ASSEMLY 12.
! Caution for the safety during servicing 1. Do not allow the customer to repair the product. ☞ The person may be injured or the product life may be shortened. 2. Execute A/S after unplugging the power supply unit. ☞ Be care of the electric shock. 3. Do not plug several plugs in the same outlet. ☞ It may cause the fire due to overheat. 4. Check the damage, pressing or burning of the power plug or outlet. ☞ Replace it promptly if it has problem.(It may cause the electric shock or fire) 5.
1. Specifications WASH TYPE FRONT LOADING TYPE DIMENSION GROSS W 669mm X D 656mm X H 910mm NET W 598mm X D 555mm X H 844mm WATER PRESSURE 50 kPa ~ 800 kPa WEIGHT GROSS 80 kg NET 75 kg WASHand SPIN CAPACITY POWER CONSUMPTION 50 kg (DRY LAUNDRY) WASHING WASHING and HEATING SPIN 220 V 180 W 240 V 180 W 220 V 2400 W 240 V 2800 W MODEL SWF-P8 SWF-P10 SWF-P12 220 V 430 W 500 W 550 W 240 V 430 W 500 W 550 W PUMPING WATER CONSUMPTION SPIN REVOLUTION SAMSUNG ELECTRONICS CO.
2. Overview of the Washing Machine CONTROL-PANEL WATER SUPPLY VALVE DRAWER ASSY DOOR SENSOR PRESSURE TUB ADJUSTABLE LEG ASSY PUMP POWER CORD BUFFER SPRING WEIGHT-BALANCE DRAIN HOSE PULLEY BELT ASSY MOTOR 4 SHOCK ABSORBER SAMSUNG ELECTRONICS CO.
3. Overview of the control panel Cotton Remaining Time Synthetic Pre-wash o 12:00 Check C rpm Min Wash Rinse Delay Start Spin Delicate Wool Speedy Eco Fuzzy control Temp 1 2 3 Spin 4 Delay Start 5 Door open Function 6 7 8 9 10 1. Detergent dispenser 2. Display panel Displays the remaining wash cycle time, error messages and cancel —. 3.
SAMSUNG ELECTRONICS CO., LTD WATER SUPPLY WASHING RINSING 1 5.0 3.0 1.5 2.0 2.0 5.0 SPEEY PRE ECONOMY 1.5 WOOL DELICATE SYNTHETIC 2.5 COTTON 1.
5. General Error Function •· When an error occurs, this function starts to keep generating error melody sounds and displays error indicators as shown in the followings per corresponding error by blinking in 0.5sec interval until the error status is completely cleared out. In this case, all the driving devices are turned off until the error is cleared out. 1.
6. Trouble Diagnosis °· As the micom wash machine is configured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide. Caution for the Repair and Replacement Please follow below instruction for the trouble diagnosis and parts replacement.
6. Trouble Diagnosis No Item 1 The power is not supplied 2 The water is not supplied. 3 The wash does not start though the water supply is stopped. 4 The wash is executed while the water is supplied. The drum does not rotate during washing. 5 6 7 The drum rotates by one direction during washing. (The drum rotates to one direction for SPIN.) Drainage problem. 8 Dehydration problem. 9 Abnormal noise during SPIN. 10 Leak breaker or current/leak breaker is down during washing.
7. Test Mode Cotton Remaining Time Synthetic Pre-wash o 12:00 Check C rpm Min Delay Start Delicate Wash Rinse Spin Wool Speedy Eco Fuzzy control Temp Spin Delay Start Door open Function 1. Driving Compartment Test Mode A. Hold down “Temp” and ”Delay Start” keys simultaneously and then press POWER S/W on. (Display shows “tESt”) Hold down “Delay Start” and “Temp” keys simultanesously (each processing for 0.3sec) and then press POWER S/W on. B.
8. Designation of Main Components 8-1 Normal / Reverse Revolution of Motor and R. P. M. Control 8 Rotor CW 9 - + CCW 5 Stator coil ROTOR 10 PROTECTOR (150 C) Stator coil MIDDLE-SPEED 5 1 2 3 4 5 6 7 8 9 10 + STATOR 9 TACHO Rotor HIGH-SPEED 8 STATOR 10 5 WASHING MOTOR • The resistance value can be slightly changed by the temperature. Resistance value Rated value STATOR(5.10) 1.64 Ω STATOR(5.1) 0.91 Ω ROTOR(8.9) TACHO(3.4) 1.9 Ω 42.
10. Assemble and Disassemble 1. ASS’Y-COVER TOP 1) Remove two screws fixing the top-cover on back side. 2) Push the top-cover back about 15mm and pull it up. 3) It’s possible to exchange and service the trans former, the pressure-senser, the noise-filter and the water valve. m 15m SCREW 2. FRAME FRONT 1) Remove the top-cover and the ass’y drawer. 2) Remove two screws fixing the control-panel on front side and the screw on right side. 3) Remove the cover-front(L) by using the (-)driver.
10. Assemble and Disassemble 3. BELT 1) Remove the top-cover. 2) Disassemble and assemble the belt. 3) Check the belt is located at center of the motor-pulley. Hook the belt on the motor pulley 1) and place it around the pulley 2). 2 PULLEY BELT 1 MOTOR 4. MOTOR 1) Lay down the washer on left side. 2) Remove the wire housing from the motor. 3) Remove the bolt fixing the motor with the box drive on back side. 4) Remove the motor. Motor Assemble Hole 5.
11. Tools for Disassembly and Assembly NO 1 2 TOOL Box driver 10mm Heater (1) 13mm Motor (1), Balance (5) 17mm 2 holes of each left and right of the shock absorber 19mm 1 Pulley hole Double-ended 10, 13 Replaceable for the box driver. spanner 17, 19mm Since the bolt runs idle when the box driver is used, use the box driver 17mm. 3 Vice pliers Tool to protect the idle and abrasion of the bolt for the box driver.
12. Expolded View and Parts List 11 10 9 8 7 12 6 5 4 3 2 1 NO. Description Code No.
12. Expolded View and Parts List 13 12 23 22 19 21 20 10 27 8 26 9 25 11 24 10 14 15 16 17 18 5 6 4 7 3 2 1 SAMSUNG ELECTRONICS CO.
12. Expolded View and Parts List NO. Description 1 ASSY-WIRE DIAPHRAGM DC91-12078A 1 2 DOOR-DIAPHRAGM DC61-20219A 1 3 ASSY-CLAMP DIAPHGRAM DC91-12077A 1 4 BOLT-W.MOTOR DC60-40138A 2 M8 L70 ZPC2(YEL) SM10C 5 WASHER-PLAIN DC60-60044B 5 ID8.4 OD13 T4.3 SBC 6 WASHER-NYLON DC60-60040A 3 ID10.
12. Expolded View and Parts List 8 1 2 13 18 12 17 15 9 19 14 16 3 7 20 10 22 11 21 5 4 6 27 23 28 24 29 25 26 31 32 33 30 SAMSUNG ELECTRONICS CO.
12. Expolded View and Parts List NO. Description Code No. Q’ty Secification 1 ASS'Y-M.
12. Expolded View and Parts List 1-1 Safety precautions 7 1 5 2 3 4 6 NO. 1 Description Code No. Q’ty Secification DECORATION-LID DC64-20013B 1 ABS SWF-P8,P10 DECORATION-LID DC64-20013A 1 ABS SWF-P12 2 COVER-DOOR DC61-10682A 1 ABS WHT 3 DOOR-GLASS DC61-00013A 1 GLASS NTR SWF-P12 4 HOLDER-GLASS DC61-40346A 1 ABS WHT 5 ASSY-HINGE DC97-00100A 1 6 LEVER-DOOR DC66-30161A 1 ZnDc L40 7 NUT-FLANGE DD60-50018A 1 M5 SAMSUNG ELECTRONICS CO.
12. Expolded View and Parts List 11 5 3 10 4 6 7 8 9 2 1 NO. 1 Description Code No. Q’ty Secification ASSY-PANEL FRONT DC97-00004R 1 ABS,WHT,SWF-P10 ASSY-PANEL FRONT DC97-00004Q 1 SWF-P12 ASSY-PANEL FRONT DC97-00004S 1 ABS,WHT,SWF-P8 2 BODY-DRAWER DC61-30348A 1 PP.WHT 3 GUIDE-LIQUID DC61-60498A 1 ABS 4 CAP-RINSE DC61-10687A 1 PP.WHT 5 ASSY-PANEL CONTRO DC97-00703C 1 SPAIN 6 INLAY-ENCODER DC64-30087C 1 PC.TRP.
9. PCB CIRCUIT DIAGRAM SAMSUNG ELECTRONICS CO.
