User Guide Introduction Thank you for purchasing the SVR-1645. This is a user manual for SVR-1645. Before product installation and operation, please become thoroughly familiar with this user manual and other manuals referenced by this manual. This user manual and the software and hardware described here are protected by the copyright law.
Contents Product warranty and limits of responsibility ............................................................................. 2 C Chhaapptteerr 11.. S Saaffeettyy C Caauuttiioonnss ........................................................... 7 1.1 Symbols displayed for each item ......................................................................................... 7 C Chhaapptteerr 22.. S Suum mm maarryy.................................................................... 10 2.1 Features ........
User Guide C Chhaapptteerr 55.. P Pllaayybbaacckk .................................................................... 22 5.1 Various Playback mode ................................................................................................ 22 5.1.1 Basic Screen Playback (16 division screen) ......................................................... 22 5.1.2 Division Screen(4/9/10/16) Playback..................................................................... 22 5.1.
6.8 Monitor Setup .................................................................................................................... 42 6.9 Event Setup ....................................................................................................................... 44 6.9.1 Event ........................................................................................................................... 44 6.9.2 Text......................................................................................
User Guide 7.4.11 Image Channel Close ............................................................................................ 73 7.5 Playback ............................................................................................................................ 73 7.5.1 Screen Division & Channel Change ...................................................................... 74 7.5.2 Image Recording ................................................................................................
Chapter 1. Safety Cautions 1.1 Symbols displayed for each item Warning Refers to information users need to know in order to prevent serious injury or death. Caution Provides information users need to know in order to prevent minor injury or product damage. Before installation Verify the supplied voltage (AC100V~AC240V) before connecting the power supply. Make sure the power supply is off before installation. Do not install in a very humid environment.
User Guide Random replacement of built-in battery by other types of batteries may cause explosion. The battery shall be replaced by the same battery. The used batteries shall be disposed carefully because they can cause environment pollutions. Dismantling and cleaning Do not dismantle, repair or modify the product deliberately. Doing so may cause a damage, an electric shock or an injury. Do not use water, thinner or organic solvent for cleaning the product exterior.
FCC Compliance Statement NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
User Guide Chapter 2. Summary This unit is digital recoding device that record the digitalized image input from 16channels to built-in hard disk and can playback. When it set functions, it can easily setup through operating mouse & button at front. Samsung SVR-1645 are digital image recording devices used to Bank, Apartment, Public offices, and are the independent product that system performance & safety are ensured.
Video Recording It can record image high quality MPEG-4 real time image into max. 480frames per a second and max. 5 seconds at pre-event. Also, it protects privacy through COVERT (Hiding image) function.
User Guide Various Copy device support : DVD-R, CD-R, USB memory Hard disk expansion device(External recording device) : SVS-5 (Option as exclusive device) Network It supports various networks like LAN, xDSL and can operate and manage main functions of product through exclusive PC viewer remotely.
Chapter 3. Product Description 3.1 Front part COPY part Classification 1. DVD-Multi for Copy Function It uses when Copy recorded images through DVD/CD media. Channel LED Classification 2. Channel LED Function It shows the status of image input and event action. JOG/SHUTTLE part Classification Function JOG can adjust set value in menu and control STEP 3. JOG/SHUTTLE function. And moving item between menus, Playback direction/Speed up & down, PTZ control is possible by Shuttle.
User Guide EVENT lamp It indicates whether event is detected. COPY lamp It indicates whether Copy works. PLAY lamp It indicates whether status of Play action. Power part Classification 5. Power button Function It is On/Off power. REC button Classification 6. REC button Function It starts or stops manual recording. Channel selection button Classification 7. Channel button Function Select Channel at Live image and Playback image. Function buttons Classification Function 8.
18. ◁/REW It moves & selects from menu, or changes rewinding playback speed from Playback mode. 19. ▷/FWD Move or select this from menu, or change forwarding playback speed from Playback mode. 20. △/PAUSE Move and select from menu, or Pause live image or playback image. 21. ▽/STOP Stop Playback in Playback mode. USB Port Classification Function It is connection terminal for external devices (Mouse, 22. USB1, USB2 USB memory stick). 3.2 Rear Part No.
User Guide No. Input/Output terminal Function name for Copy 11 VGA OUTPUT Output port to connect PC monitor 12 RS-232C RS-232C terminal 13 RS-485 Connection terminal for expandable controller, Speed dome camera 14 RELAY OUT Relay out terminal 15 SENSOR IN External sensor input terminal 16 AUDIO IN(D-SUB) Audio out D-SUB connection terminal 17 DIO DIGITAL IN/OUT connection terminal Refer to detailed description for installation & the use from “Installation Guide”. 3.
4.1 Basic Screen view - If Power connects, DVR is on aquatically. - All LED is On/Off in order and is booting. - After booting, basic 16 divisions monitor screen appears. ※ If user’s password is set, password input window appears. 4.2 Single image view in full screen - Press channel button wants to see or click left mouse. - Press [MULTI] button or click left mouse once again to move to division screen again. 4.
User Guide - Move to “Screen Setup” from OSD menu. - Move to “Monitor” under “Screen Setup,” and press [ENTER] button or click left mouse. - Select “SEQ. Dwell Time” and set wanted value from 1 to 16 seconds. When it sets to ‘Off’, user sequence view does not operate. - User Sequence mode is usable by pressing [AUTO] button from every division mode. - Press [AUTO] button once again to exit from User Sequence mode. 4.4.2 User Sequence mode - Press [AUTO] button.
4.5 Event Screen view - In case of Event, it can sets relevant screen to Pop-up automatically. - Setup period of relevant Pop-up sets relevant time from “Switch to Event Screen” under “Monitor” menu. When Event occurred at several channel simultaneously, division channel as many - channels as related appears. For example, if event occurs to 3 channels together, the images appear to 4 division screen automatically. Press one of any channel button among pop-up image to return to original screen. 1.
User Guide 4.8 PTZ Control It connects PTZ controller to DVR, and it can control PTZ while viewing image in real time if it sets relevant protocol to “Serial Setup” menu. To execute PTZ, press PTZ button from front function button and select PTZ function through Func button. - Move to the channel wants to control. - Press PTZ button or click PTZ button from Function menu using mouse.
4.8.5 Auxiliary On application This menu used when it uses special function of PTZ device from real time monitoring mode. - Set Aux number using up/down direction key or mouse wheel. - Select On, and press Enter button or mouse click - (Total 16 Aux functions are available.) 4.8.6 Auxiliary Off application - Set Aux number using up/down direction key or mouse wheel. - Select Off, and press Enter button or mouse click - This menu used when it stops working special function of PTZ device. 4.
User Guide Playback, and Spot monitor can be used for two functions of Single channel live image and Event pop-up image. Chapter 5. Playback 5.1 Various Playback mode 5.1.1 Basic Screen Playback (16 division screen) - Press [PLAY] button from monitoring mode or click Play button from Function menu using mouse. - If it press [PLAY, ▷] button and [FWD] button for changing speed, it playback image forwarding in 1x speed set first.
monitor mode. Also, when Playback by pressing [PLAY] button, it playback recording image from the time user played recently. PAUSE It pause Playback. When using mouse, press Pause button from Function button. STOP Stop Playback. When using mouse, press Stop button from Function button. FWD Whenever pressing button, playback speed is changed. (x1, x2, x4, x8, x16, x32, x64, x1/2, x1, x2, x4 ~~). At Live, press [FWD] button to Play recorded images in a minute ago from present live time.
User Guide 5.2.1 Time Search Input Data & Time to search, and playback image moves to searched date & time by selecting Search. Start-REC Time It indicates Date & Time starts recording first. End-REC Time It indicates Date & Time of recording the most recent. Search Time Select Date & Time wants to search from starting time to present time of Recording. Search Button Search the image of time input. 5.2.2 Calendar Search It can use more easily search the wanted point using calendar.
5.2.3 Event Search It can appoint specific period and divide to all channels, some channels, All, MD, Sensor to search. When using button at front, it can change Date/Time using up/down button. And when using mouse, it can set the part wants to change through rolling wheel. Selected result is shown to Event Search window in separate list. It can playback relevant date, Time by pressing Enter button after selecting searched list or rolling wheel.
User Guide Channel It selects the channel wants to search. After selecting, it can change the value using up/down key or change it through mouse wheel. Start Time Input the starting date & time wants to search. After moving to the location to change using left/right key and press Enter, it can change the value through up/down key or mouse wheel. Interval It divides into regular base for searching and indicates result. It can change through up/down button or mouse wheel.
location of Channel and select it using Enter button or mouse wheel. It appoints starting date & time wants to. It can set up using up/down From button at front or mouse wheel. It appoints the last date & time wants to Copy. It can set up using To up/down button at front or mouse wheel. Selecting Disk Select media wants to Copy. Press Enter at Select Disk part and select disk. Start COPY. Press Start button through Enter button or click left mouse Start button.
User Guide Type Select RE4 using up/down button or mouse wheel. Channel List Press Enter from Channel part to pop-up channel selection window or pop up Channel List using mouse wheel. Selecting Among 16 channels, it can select a part or all channels. Select the Channel channel from Channel list and press Enter button or click left mouse button. Appoint starting date & time wants to Copy. After selecting the part From wants to change, it can setup using up/down key or mouse wheel.
5.3.3 AVI It is to Copy a part of one channel selected to USB memory or HDD. Type Select AVI using up/down button or mouse wheel. Channel Select the channel wants to Copy using up/down button or mouse wheel. From Appoint starting date & time wants to Copy. Move to time, year etc using left/right button and change Date/Time using up/down button. When using mouse, left mouse click to the location wants to change and change it using wheel. Duration Appoint Copy time.
User Guide Chapter 6. Configuration 6.1 Record Setup There are 4 different modes to DVR recording, and it can see Setup relation like the following structure of picture. It explains Recording type briefly. Refer to each item below for the detailed setup relate to Recording. 6.2 Time Setup (System Time) Time setup of production is required before Record Setup. It is very important to setup to local time for recording data protection of product. It does not recommend changing the time during recording.
6.2.1 Method of Time Setup When it changes the time during the condition of recording already, it recommends Copy for important data before the time change because it changes the time of image recorded. - Press [MENU] at front or Menu button at Function. - Move to “Quick Setup” menu. - Select “System Time” of “Quick Setup” using Enter button or wheel. - When pressing button in normal order, 6.2 Time set-up screen is appeared.
User Guide follows by pressing business. Except “Date/Time” setup, other setups are saved automatically when it is closed completely, but “Date/Time” setup does not saved automatically because it can affect to HDD recording file system critically. When it applies the content changed, it must press [Apply Date/Time] button to apply. 6.3 Camera Setup This menu is to setup the condition for each camera connects to the product.
6.3.1 Method of Camera Setup It moves to “Cam#1 ~ Cam#16” under “Camera” of Screen Setup using direction key or mouse wheel after pressing [MENU] button.. 6.3.1.1 Title Set up Camera Name. Relevant character setup menu appears if it press [ENTER] or mouse click. Character input window appears when it inputs characters. According to menu, Character input window can be different but same setup. - Character input uses direction button. - Press relevant character when using mouse.
User Guide 6.3.1.6 PTZ It sets PTZ Home, Idle Time, Port, Address relate to PTZ device. 6.3.1.6.1 PTZ Home / PTZ Idle Time This is menu to setup camera supports PTZ (Pan/Tilt/Zoom) and it moves to PTZ assigned when there ions movement during specified time. It sets Preset number & Time using left/right button or mouse after pressing [ENTER]. 6.3.1.6.2 PTZ Port This is menu to setup camera supports PTZ (Pan/Tilt/Zoom).
Recording Speed/Quality There are all 5 setup conditions. Default set value is ‘No Rec.’ that means does not record. No Rec. / Low / Standard / High / Custom Except “Custom,” setup condition sets to synchronies ‘Speed (fps)’, ‘Quality’, ‘Resolution’ automatically. Resolution There are total 3 conditions. (CIF/ HALF/ D1) Resolution setup is changeable when ‘Recording Speed/Quality’ is set to Custom. Method of Record check If Record Setup is completed normally, ‘REC LED’ at front part blinks.
User Guide 6.5.2 Setup by Channel It can set Time Schedule, Macro differently by each channel. It sets 1~8CH to Weekday day, Low, and can set 9~16 to Full Time, High Recording Speed/Quality There are total 5 setup conditions. (No Rec./Low/Standard/High/Custom). “Custom” can set the status of Speed, Quality and Resolution to user wants. Resolution There are total 3 setup conditions. (CIF/HALF/D1) Resolution value set here is applied to user’s recording, Event recording.
is “ON” at configuration and macro is more than “low” it starts event recording when there is digital input and it stops event recording if digital input is stopped. 6.6.1 Event Source Setup For Event Recording, it looks into the method of Sensor, Motion Detection and Text setup. 6.6.1.1 Sensor Setup This menu is to set Action & Type of sensor input. It supports 2 types of Sensor, Normal Open (N.O.) & Normal Close (N.C.). Configure it according to the sensor type what the user uses.
User Guide Motion Detection It sets 12 different sensitivities; low, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, High 6.6.1.3 Text Setup This menu is for configuring input text information and user set "Event Configuration" value in OSD menu by Text. Recording It can On/Off recording of Text input. 6.6.2 All Event Record Setup This is setup all analog channels in identical condition.
Sensor/MD/Text It sets whether it synchronize with Sensor/MD/Text event. Pairing means synchronizing 1:1 between channel and Sensor/MD. 6.6.2.1 Setup by Channel Event Source - Through Event Source can select 16 Sensors, 1 MD and a Text input. - Selecting Sensor selects box of relevant number. - Selecting MD, Text selects box when it needs to use. Macro There are total 5 setup conditions. (No Rec/Low/Standard/High/Custom).
User Guide Pre Event (sec) It can set max. 5 seconds. Post Event (sec) It can set max. 60 seconds. 6.6.3 Manual Recording Setup When user presses [REC] button at front part, this menu can setup recording condition of image. If manual recording starts, existing recording setup set is ignored and it records image in the value set from Recording Setup>> ‘Manual’. It records to the value (sec) set in ‘Pre Event’ & ‘Post Event’ of ‘Manual’ menu.
Post Event (sec) It means the time record after user press [Rec] button. It can set max. 60 seconds. 6.7 Audio & Other Setup (Audio Recording) Through this menu can set recording of Audio setup & No Video. 6.7.1 Audio Setup It can set Audio channel, Recording, Gain, and Sync. Audio Channel Select channel wants to use Audio. Recording It sets whether it records audio using. In case of Off set, audio outputs to live image only and Playback also when it sets to On.
User Guide 6.7.2 Audio Mix Select Audio to use from Live image. In case of All setup, all input audio is out in mixed. And when selecting specific audio, it is out only selected channel unconditionally whatever any channel is selected. 6.7.3 Record No Video It sets whether it records the input image that has fault or the channel deletes image intentionally or not.
Monitor & Spot Monitor The entire function of DVR is available for monitor and spot monitor can use single channel monitor and event pop up. Switch to Event Screen (sec) In case of Event, it sets to Pop-up relevant screen aquatically. Pop-up duration can set from 2~10 seconds and select among Keep. If it sets to “Keep,” it keeps Pop-up screen. At this time, press any channel button to cancel Keep mode.
User Guide Multi Screen Definition It defines 4E (4 channels), 9B (9 channels), 10A (10 channels) channels of Multi Screen in advance. The method of Multi Mode is through [Enter] button after selecting Mode and right window of mode, or it can select the channel through [Enter] button or mouse wheel after window open and the channel select using mouse wheel. VGA Mode It can select among 3 resolutions of VGA output, 800 x 600, 1024 x 768 and 1280 x 1024.
MD MD detects movement by each channel or all channels, and use to inform MD to user. - Channel It can set channel to All or 1~16CH. - Sensitivity In case of Sensitivity, it can set sensitivity per each channel Off, Lowest, Low, Middle, High, Highest. - Area Area sets detecting area when MD set. In case of All set, it can select Set All, Clear All. In case of setup by each channel, it can set to Set All, Clear All, and Select Area.
User Guide “ESC” or right mouse click to return previous menu. 6.9.2 Text Recording It can On/Off recording in regard to Text input. Sync Test With It selects Text data and synchronically channel. Seek Header Various data types come from external device (Access Control, POS, and ATM etc). Like Star Finger 007, it does not need protocol that is registered already. If not, it requires parameter to grasp the structure of the data from Text data input continuously.
need a line less tan others. But because DVR can not detect this automatically, it is considered to last line after some time from registered time of last line, and it decides whether it records a registered data as complete data. Lines It defines a data consists of how many line. In case of External device, it must consult with seller before installation because it may be not recognized according to feature. 6.9.3 DIO DIO is Port able to use digital Input & Output simultaneously.
User Guide 6.9.4 Event Action Event Action sets workable Action according to Event Input. Select Action Select Action can select R1~4, Buzzer, E-Mail. Action Duration Action Duration operates when Relay works and keeps as long as the time set, and also Buzzer keeps in same way. It works E-Mail Sending in an interval of time set. Action Source Action Source can setup Sensor, Motion, and Text separately. Also, all event input can setup simultaneously.
check if it is sent to specific DVR. Event Action in Special Time It sets whether it operates Event Action in Special Time or not. 6.9.5 Network When DVR connects to network, this is menu to setup relevant network data. Type It sets up network line type (Ethernet/xDSL) connects to DVR. When it is connected Exclusive line or cable model or LAN of DVR, it sets to ‘Ethernet’. When DVR is connected to xDSL in PPPoE method, it sets to ‘xDSL’.
User Guide IP Address IP Address is used when communicating DVR & CMS and is used to connect from Webviewer to DVR. But it is available when Net Mask and Gateway are set. Net Mask Net Mask assigns the range able to input IP Address and same range of IP make possible to communicate. Net Mask receives from network administrator and use. Gateway Gateway must input so that IP Address communicate, and it receives from network administrator and input.
User ID/Password If DVR is connected to xDSL, it must set ID & Password. Status It indicates the condition of DVR connection. 6.9.7 DDNS It DVR is connected to cable model or xDSL modem, IP address is changed whenever it tries to connect to ISP. In this case, user can not find IP address changed. If DVR that uses fixed IP is registered to DDNS, it can find IP address changed easily when it is connecting to DVR. In order to register dynamic IP address in DDNS, please, refer to the below explanation.
User Guide - Agreement the general terms and conditions - SIGN UP page: check ID availability 2) The product registration is possible after sign up.
- Product List (If you didn’t register products, there are no list) - Product Registration (Check ID availability) - Check the registration at product list 3) Set-up DDNS information.
User Guide SVR-1645 can be set up under the network screen in the order as listed in the menu. If you press the menu button and select the network, you will see the screen as shown in the diagram below. In the below screen, select DDNS as “yes,” and in the ‘DDNS SERVER DOMAIN NAME’ enter DDNS server address. (Default: www.samsungipolis.com ) ID and PW are the same as that created when you registered the product on the iPOLiS homepage. Please enter the domain ID and PW.
To register fixed IP to DDNS refer to following explanation for setup. Interval For the continuous registry, it sets register period from ‘WRS Interval’. According to setup value, fixed IP address renews its data to DDNS server regularly. If user sets register period to ‘0’ or it does not transmit any data of DVR for 2 days, its data is deleted from DDNS. Server This menu sets server address to register. WRS address is 222.121.60.188. ID Input ID registered when joins to DDNS server.
User Guide Sync with NTP It cans NTP function On/Off. NTP Mode It sets whether it operates NTP mode of DVR to Client, Server or Both. NTP Server Loc. When NTP Mode is set to Client, it is Enable. It sets whether NTP server is on Local Network or internet (Public). NTP Local Server IP When it sets NTP Server Loc. to Local, it is Enabling and sets IP in server. Input IP of DVR that sets IP in NTP server or NTP Mode to Server at local network. Interval (min) Set the period of time to synchronize.
Serial port Select the port to control by connecting with the unit Device Set external device connected. Interface This menu is to setup using which interface. It fixed COM1, COM3 to RS-232C, and COM2, COM4 to RS-485. Baud rate/Parity/Stop (bit)/Data (bit) Configure the value same as the set value of external unit. .
User Guide 6.10 System Setup 6.10.1 Setup Remote Controller ID Max. 16 remote controllers ID are selectable, and it can control max. 16 DVR It can register Remote controller as following order. - Direct Remote controller to DVR. - Press ID button that suits to Remote Control ID set. - If Remote controller ID is identical to DVR ID, DVR buzzers. - After tune ID, Remote controller is available to use.
Firmware Update After saving firmware for USB into USB device, it connects to DVR and can update Firmware using ‘Update F/W’ button. Update firmware for USB is provided in “*.dat” file. Load Configuration It sets DVR setup value stored in USB memory by transmitting to DVR. Save Configuration Save preset setup status of DVR to USB device. Default It used when it sets existing set value to first factory value to ship. To create first value press “Default.
User Guide capacity setup. Block Playback This menu is to make visible limitedly the recorded image in HDD as much as the date set. If it records for 30days and sets Block Playback to 2days, it can play the day before including 30days among 30days. It can set from 1day till 31days. Disk Manager Disk Manager is to manage internal or external HDD using. It manages the state indication of HDD, Bad Block, Size, Add, Remove etc. Disk Status It can view HDD temperature, state of HDD installed in System.
- “This disk can be added without format. Nevertheless, do you want format this disk?” - If select Yes, it maintains previous data as it is and Enable to use HDD. - If select No, it deletes previous data and Enable to use HDD. In case of the change of HDD No - It pops up NOTICE window and shows next message using [Enter] button or rolling mouse wheel at the condition of Enabled Yes. - “Disk will be removed” - If select Yes, “Recording disk removed” is appeared and changed to Enabled No. - HDD is not used.
User Guide Weekday Start/End Among Monday to Sunday, it sets Weekday time period. The other part unset is under Weekend time period. Day Start/End It sets Day time period using up/down direction key. Unset parts means Night time period. 6.10.5 Special Time Special Time is able to four setups. It can set another specific time period in each time zone (Weekday (Day), Weekday (Night), Weekend (Day), Weekend (Night)).
Use when it sets of irregular exceptional time. It can set max. 30 irregular exceptional times and set Start Time, Duration, Profile. Start Date & Time : It indicates stat date & time of exceptional zone. Duration : It sets time apply Profile from exceptional time set. Profile : Profile is to set simultaneous recording with Schedule setup of Schedule Recording, and it can set to No Rec, WDD, WDN, WED, WEN.
User Guide This is menu to save the state of setup at other menu and exit to live screen, it can select into Set or No Set. Select “Yes” when it saves the setting and exit, or select “No” when it does not save setting and exit. Do not Save This menu is to exit without saving the status of setting at other setup.
Chapter 7. Web Viewer WebViewer is web program loaded into product that can view image recorded or monitoring image of product in realtime through web browser in PC remotely able to use Internet. Structure of Web Viewer is divided into Monitor which can monitor image in real-time with Login page, and Playback which can playback recorded image. 7.1 LOGIN If user inputs IP address and Port on browser address box, user can access to Webviewer Login page for example type "http://192.168.1.25:4000.
User Guide It can use ID & P/W of an administrator and 10 general users. It is able to change administrator and user’s ID for security. Cancel by check ‘Use’ of user’s account disusing. It is the state changed user’s ID & Password at Configuration Tool. After the end of account setting, set authority of user’ ID. Check ‘Hard’ in user account at authority setup of Configuration Tool to use Playback page.
can use. When it shows 1CH image only, check the rest channel and uncheck the rest channels & functions. 7.3 Usable Browser WebViewer is optimized to Windows Internet Explorer 6.0 or higher. For smooth use, Windows Internet Explorer 6.0 or higher is installed in PC using. Webviewer Installer It provides auto installation program to use the function of WebViewer at login page. It installs ActiveX which is able to use WebViewer function through PC connects at first to WebViewer.
User Guide 7.4.1 Screen division & Image location change It shows to 9 divisions, 16 divisions, or 32 divisions according to channel number of product when connect to Monitor page. It can change to 1, 4, 9, 13, 16 divisions by click number of upper page. Also it can switch to 1 screen mode by click screen part. Among Playback image, double click after load mouse to the channel going to convert to any 1 channel temporary.
7.4.2 Moving Playback If it clicks following picture in top page, it moves to Playback page. 7.4.3 Channel On/Off Channel On/Off button is located on left page. It can On or Off by click the channel wants, and default is On. Above picture is Off state about 9~16CH. When Channel is Off, it changes to grey color and image is not visible and is changed to black. Inactivated channel button is the case that it does not support at relevant product. 7.4.
User Guide 7.4.5 Relay operation It can Relay On or Off of product. If it clicks the number of button, Relay is On and icon change from Blue to Orange color. Inactivated sensor icon is the case that it does not support at relevant product. Reply work needs user’s authority. Refer to user guide in Product for User Authority Setup. 7.4.6 Microphone use It can microphone On or Off and Default is Off. In case of click button, projecting button changes to Blue and microphone is available.
7.4.8 Image Recording & Image Storage 7.4.8.1 Image Recording After selecting channel wants to recording from image monitoring, it selects “Rec Start” pressing right mouse button. It can record image max. 10 minutes. It indicates recording time on the image executing Quick Recording. Among image recording, if it closes recording by click “Rec Stop” of right mouse again and open dialog box to record file recording, user saves to temporary directory with naming to the file. Recorded file is saved to “*.
User Guide Pan, Tilt Control Click right mouse at the image wants to control PTZ and select “PTZ” menu. It shows cross line at center of image and Pan, Tilt works when mouse click the image. If click left/right direction from the center, PAN controls, and Tilt controls by click to up/down direction. Far from the center, Pan/Tilt works faster. Zoom, Focus Control If it move mouse to left, right edges, it shows slide bar for Zoom, Focus. A unit that is possible to Area Zoom has Zoom Zero work button.
7.4.10 Audio Use When synchronized audio and channel is set, it can execute audio listening by click “Listen” menu of pop-up menu that comes through right mouse click on the image. And audio listening is possible through Uncheck of Mute. 7.4.11 Image Channel Close It can cancel connection of image monitoring by click left side channel button of image. And Screen comes to black. To reconnect the channel disconnected clicks channel button that is turned Off to reconnect relevant channel. 7.
User Guide Playback consists of 16 division screen can playback using Search through calendar by recording period or Move period button. It can Copy recorded image and Print Pause iamge or can save to bmp file. Let’s study about introduction & function and naming of each part. 7.5.1 Screen Division & Channel Change Playback supports 1, 4, 9, 16 division screen. Using the menu as about picture can select division screen.
The window for input Memo appears. It can print image through printer connected if press OK. Print material includes ‘Printing Date’, ‘Channel name’, ‘Recording Date’ ‘Event’, ‘Memo’. 7.5.4 Web Monitor move It can move to Web monitor page by click ‘Monitor’ button at left top of page. 7.5.5 Channel On/Off The function is same as channel On/Off at Web Monitor. It is On/Off button positioned on right side of page, and it can On or Off by click channel wants. Default value is On condition.
User Guide 7.5.8 Function button at image below ① It indicates Playback range of image recorded. ② It can change playback time zone back & forth by click as time as set at (5). ③ It can ‘1 frame back’, ‘Play backward’, ‘Stop’, ‘Playback’, ‘1 frame forth’ from left button. ④ It is function to set Playback speed. After button click, it can set playback speed relevant to ‘0.5x, 1x, 2x, 4x, 16x, 32x, 64x, All’. ⑤ It can setup Playback range.
Use HDD List Use HDD Model List Seagate Technology Western Digital Capacity Model Capacity Model 750GB ST3750840SCE 750GB WD7500AVCS 500GB ST3500830SCE 500GB WD5000AVJS 250GB ST3250820SCE 250GB WD2500AVJS Specification Item Video Input Video Output Analog Ch.
User Guide Time, Calendar, Event, Thumbnail, Text, Smart(Remote Search Mode Playback Mode Playback Only) Speed Multi Screen Forward, Reverse, Pause, 1/2x, 1x, 2x, 4x, 8x, 16x, 32x, 64x 1, 4, 9, 10, 16Ch Simultaneous Live Display/Playback/Record, Multiplex Function Remote Monitoring/Playback Automatic E-mail, Internal Buzzer, Relay-out, Pop-up Event Notification Screen, Network Event File System Intelligent Power Failure Recovery Watermark Yes Password Protection 2 Level (Admin/User) DVD Write
Trouble Shooting 1. No DVR booting Check Power Check Power code 2. No Image on Monitor Check monitor power Check monitor & cable condition of DVR Check monitor cable port Check whether DVR power is On 3. No image of some channel Check Camera power Check Camera image input Check DVR input port Check On/Off Activity setup in Screen setup heck Covert setup in Monitor setup 4. No Recording Check whether HDD is installed from Disk Manager Check Record setup 5.
User Guide Check PC IP Ping Test 10. Case to contact seller In case of following conditions, stop using product immediately and const to seller for the service after Power off. During using, when abnormal work happpens to product (ex.
Dimension 81
User Guide 82
