Vacuum Cleaner SU-2950 Series FOR HOUSEHOLD USE ONLY Operating Instructions IMPORTANT SAFETY INSTRUCTIONS ......................... 1 ASSEMBLING PARTS ..................................................... 2 OPERATION .................................................................... 3 MAINTENANCE ............................................................... 5 TROUBLESHOOTING .....................................................
IMPORTANT SAFETY INSTRUCTIONS Thank you for purchasing a Samsung vacuum cleaner. When using an electrical appliance, basic precautions should always be followed, including the following: PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. WARNING: To reduce the risk of fire, electric shock, or injury: • Do not leave vacuum cleaner unattended when it is plugged in. • Unplug from outlet when not in use and before servicing. • Do not use outdoors or on wet surfaces.
A s s e m b l i n g Pa r t s Identifications of parts The assembled cleaner will look like the illustration to the left. 1. Handle 2. Power switch 3. Quick release cord hook 4. Post-Motor Filter 5. Crevice tool 6. Handle release 7. Carrying handle 8. Hose 9. Extension wand 10. Combination tool 11. Cyclone-Lever 12. Dirt Cup 13. Filter Cup 14. Upper Tank 15. Cap Cyclone 16. Hose Wand Base 17. Height Adjustment Dial 18. Hose Clip 19.
Operation 2-1 2-2 2-3 ON-OFF Switch Handle positions Transporting cleaner The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating for general operation on carpet and floors; low for reaching under low furniture. Step on handle release pedal to lower handle. To move your cleaner from room to room, put the handle in upright position, tilt the cleaner back on its rear wheels and push forward. 1.To turn cleaner on, press the Power switch. 2.
Operation 2-6 2-7 2-8 Cleaning lightweight flexible rugs Carpet height adjustment Stand on one end of rug and move cleaner toward other end or edge. Before reaching edge, push down on handle. This will lift up the nozzle(front of cleaner)and will prevent rug from clinging to cleaner. Continue to lift front of cleaner so that when you have reached the edge, it is completely off the rug. Move cleaner back to start again, lower front of cleaner, and use only forward strokes.
Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness. When to empty the Dirt Cup The dirt cup needs to be emptied when the dirt reaches the "Full" line on the side of the Cup. If more dirt than this accumulates, your cleaner will not operate effectively. Note: All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming. Emptying the Dirt Cup Disconnect cleaner from electrical outlet.
Maintenance The belt The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner. The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition. 3-7 3-8 How to replace Remove agitator and used belt. Discard used belt. When to replace Disconnect cleaner from electrical outlet. To check belt, remove bottom plate as shown in “How to replace.
Maintenance Clearing Blockages Disconnect cleaner from electrical outlet. The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt Cup can sometimes become clogged. If you notice a change in the sound of the vacuum motor, check for blockages. 3-14 3-15 3-16 Check Upper Tank and Grille Cyclone. To open the Cap, grasp the holder and turn Toward the left. If the Grille was blocked, check and clear the grille in the center of the Cyclone.
Tro u bl e s h o o t i n g Check this list of possible problems and solutions before bringing your vacuum to a service center. Problem : Poor job of dirt pickup Problem: Cleaner won’t run Possible Cause Possible Solution · Full or clogged Dirt Cup · Empty the Dirt Cup and check for blockages. · Broken or worn belt · Replace belt. · Clogged hose or nozzle · Clean hose or nozzle area. · Hole in hose · Replace hose.
MEMO
MEMO
DJ68-00294M* REV(0.
