SYSTEM CONTROLLER User Manual SPC-6000
System Controller User Manual Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
overview Important Safety Instructions ● 1. Read these instructions. overview 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
overview WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PROCUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK).
Please read the following recommend safety precautions carefully. Do not place this apparatus near. Do not attempt to service this apparatus yourself. Do not place a glass of water on the product. Do not install near any magnetic sources. Do not block any ventilation openings. Do not place heavy items on the product. User’s Manual is a guidance book on how to use the product. Below is a key to the following signs that are used in this manual. Reference : Providing useful information for the user.
overview This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
CONTENTS 3 9 10 11 Important Safety Instructions Key Features What’s Included System Controller at a Glance installation 14 15 15 Precautions Before Installation Adjusting the Screen Angle of the System Controller Switching the Layout of Joystick and Jog Shuttle 14 16 overview 3 ● overview connecting to an external device 17 23 To Connect a RS-485 Device Connecting to other System Controller using the menu 24 24 30 32 Getting Started Controlling the PTZ Camera Controlling DVR Controlling MAT
overview menu setting 34 34 35 35 40 42 To Access the Main Menu PTZ setting DVR Setting Controller Setting Firmware Update To Check the Controller Information appendix 43 44 45 Specifications Q&A GPL/LGPL Software License 34 43 _ overview
Key Features • With RS-485 communications, the control distance is a maximum of 1km. • Integrated system control • With a single system controller, you can control all cameras (receiver unit), DVRs and MATRIX. • Multiple system controllers can be connection. • You can control different sites and connect up to 16 controllers simultaneously. • Switch the joystick and jog shuttle module positions.
overview What’s Included Unpack the product package and place the product on the floor or a flat surface. Check if the following components are all included in the product package.
System Controller at a Glance ● Front Side b k j i Item a b c d e f DVR Play Bar DVR Control Bar LCD Display SETUP Bar c d h overview a e g f Description Play/Pause, Fast Forward/Fast Backward, Stop, Record Access the selected menu, search, select a split mode, or control the alarm. Display the operation status and the setup menu of the system controller. In a combination with the [FUNC] button, you can access the Setup menu.
overview Item g h i Camera Lens Bar Navigate, ENTER, ESC Number (0-9) Buttons j Controller Selection Bar k Jog Shuttle 12_ overview Description IRIS Control Iris (CLOSE/OPEN) FOCUS Adjust the focus (NEAR/FAR) ZOOM Zoom In/Out (WIDE/TELE) Navigate Navigate through menu items. ENTER Move to a desired item using the navigation buttons and select it. ESC Cancel the current operation. Used to specify numeric characters for camera, monitor, DVR or Preset settings.
Rear Side ● overview a Item a b Video In/Out MATRIX c RS-485 d USB Port e Power f Cable Hook M b c d e f Description Video input/output port Matrix connection port PORT 1 Connected to a controller such as camera or DVR through RS-485 communications. PORT 2 Connect to other SPC-6000 system controller. Used for backup of the system controller settings or upgrading the firmware. DC 12V input port ( ) To prevent the power cable from being loose.
installation Precautions Before you install the product, read through and comply with the following instructions. • The product is designed for indoor use only. • Keep it away from water or moisture. • Do not put excessive force on it. • Do not pull out the power cable forcibly. • Do not dismantle it at your own. • Use only the rated I/O range. • Use only the provided power cable. • Use the power plug containing the earth wire if available. • Install the system controller on a flat table.
Before Installation ● • You must turn off the product before installing it. • Keep it away from a strong magnetic field or electric interference, or wireless devices such as radio or TV set. • Keep the installation site clean and dust-free all the time while or after you have installed the product. • Place it on an unsealed, flat surface at an optimal temperature. Install it at least 15cm away from the wall. • Do not close the ventilation hole or put a conductive object in it.
installation Switching the Layout of Joystick and Jog Shuttle For convenience you can switch the position of joystick and jog shuttle module. J To switch between left and right, turn off the system controller and switch the modules manually. Or, press in the controller setup menu and switch the modules manually. (► page 38) 주의 : 전원을 끄고 모듈을 탈착하십시오. Caution : Turn the power off and separate the module. 1.
connecting to an external device SPC-6000 system controller can be used in connection with an external device such as camera or DVR. ● With the system controller, you can control the PTZ camera or DVR that supports RS-485 communication protocols. 1. Connect the rear PORT 1 with RS-485 port of the PTZ camera or DVR. 2. According to the external device connected, select Half Duplex or Full Duplex connection. M For the Half Duplex system, use TX +/- terminals.
connecting to an external device If connecting the keyboard without using MATRIX Main Controller Sub1 Controller Sub2 Controller Sub16 Controller 18_ connecting to an external device
If connecting the keyboard using MATRIX ● PTZ Camera / DVR Sub Controller PTZ Camera / DVR 1. Connect the [MATRIX] port of the main controller to the [KEYBOARD] port of the matrix. The MATRIX port contains the power line so you don’t need to supply DC 12V separately. 2. Connect TX+ and TX- of the sub controller to T+ and T- of the matrix, respectively. The baud rate between sub controllers in sync with MATRIX will be fixed to 9600 bps. The MATRIX ID is fixed to . .
connecting to an external device Connecting the PTZ Camera By connecting RS-485 port on the rear of the PTZ camera with PORT 1 of SPC-6000, you can control the camera. M Depending on the camera, the polarity may differ. For more information, refer to the user manual of the PTZ camera. For the half duplex system - Connect RX (+) of RS-485 port of the PTZ camera with TX (+) of PORT 1 of SPC-6000.
● Connecting SRD-16XX/8XX series, SHR-8/7/6XXX series or SVR-1670 with DVR For the half duplex system - Connect TX (+) of RS-485 port of the DVR with TX (+) of PORT 1 of SPC-6000. - Connect TX (–) of RS-485 port of the DVR with TX (–) of PORT 1 of SPC-6000. For the full duplex system - Connect TX (+) of RS-485 port of the DVR with RX (+) of PORT 1 of SPC-6000. - Connect TX (–) of RS-485 port of the DVR with RX (–) of PORT 1 of SPC-6000.
connecting to an external device Connecting SRD-4XX or SHR-604X series with DVR Connect RS-485 port on the rear of SRD-4XX or SHR-604X series with SPC-6000. ❖ For the half duplex system - Connect TX (+) of SRD-4XX or SHR-604X with TX (+) of PORT 1 of SPC-6000. - Connect TX (–) of SRD-4XX or SHR-604X with TX (–) of PORT 1 of SPC-6000. PC-based DVR - Connect between PC-based DVR and SPC-6000 using RS-485 port on the rear of the DVR.
Connecting to other System Controller You can connect up to 16 controllers simultaneously. ● For communication settings of the controller, refer to “Sub List” of “Menu Setting”. (► page 37) For the half duplex system - Connect TX (+) of PORT 2 of SPC-6000 with TX (+) of PORT 2 of the other SPC-6000. - Connect TX (–) of PORT 2 of SPC-6000 with TX (–) of PORT 2 of the other SPC-6000.
using the menu Getting Started 1. Turn on all system component devices. 2. When you connect the power adapter to the rear port of the system controller, the login dialog appears. . Use the number pad to enter the password and press [ENTER]. The main menu of the PTZ control system appears. The default password is “4321”. Controlling the PTZ Camera To enter PTZ control mode Press [PTZ] of the controller. To select a camera 1. Use the number buttons to enter the number of the camera of your choice. 2.
PAN/TILT Control You can use the controller joystick to adjust the pan/tilt angle of the camera. ● The farther from the center of the joystick is, the faster the moving speed becomes. Turn the joystick clockwise, or press [ZOOM TELE] to control the zoom-in operation of the camera. Turn the joystick counter clockwise, or press [ZOOM TELE] to control the zoom-out operation of the camera. FOCUS Press [FOCUS FAR] or [FOCUS NEAR] on the controller to fit the camera focus.
using the menu SWING You can move the camera between two preset points to monitor the course. Swing setup 1. Select from the menu screen. 2. Press . . Use the number buttons to select PAN/TILT and specify the start preset and end preset. . Specify the speed and dwell time. . Press . To execute the swing 1. Select from the menu screen. 2. Use the number buttons to select PAN or TILT for the swing type. . The swing function will be executed.
GROUP ● You can make a group of multiple presets before calling them in sequence. Using the menu To set a group 1. Select from the menu screen. 2. Select . . Enter a group number and press [ENTER]. . Specify the speed and dwell time. . Press . To execute the group function 1. Select from the menu screen. 2. Select . . Enter a group number and press [ENTER]. . The group function will be executed.
using the menu TOUR You can make a tour of at least one group before executing the groups in sequence. To set a tour 1. Select from the menu screen. 2. Select . . Each time you press the number of a group that you want to add to the tour, the group will be added to the tour. You can add up to 6 groups to a tour. . Press to apply your settings. To execute the tour function 1. Select from the menu screen. 2. Select . .
To execute a trace 1. Select from the menu screen. ● 2. Select . Using the menu . Specify a trace number to execute. . The trace function will be executed. Auto Focus 1. Select from the menu screen. 2. The auto focus feature will be activated. RESET 1. Select from the menu screen. 2. The camera will be reset. TARGET LOCK 1. Select from the menu screen. There appears a rectangle box on the camera video. 2.
using the menu Controlling DVR Depending on the model, the DVR may have different features available. For details, refer to the applicable user manual. M An improper setting may cause a problem using the DVR. To select a DVR 1. Press [DVR]. 2. Use the number buttons to enter a DVR number (0~255) and press [ENTER]. . The main menu screen appears. It differs depending on the model. M For a DVR that supports SRD protocols, the menu screen displays only menu items available.
To select a DVR channel ● 1. Use the number buttons to enter the number for a desired DVD channel. Using the menu 2. Press [CAM]. To control the DVR menu 1. To control the menus of the selected DVR, press [MENU] in the DVR control bar. 2. Use the direction buttons to move to a desired menu item and press [ENTER]. To control the PTZ device that is connected to DVR Depending on the DVR model, you may not control the PTZ device that is connected to the DVR.
using the menu Controlling MATRIX To control monitor and camera in Matrix mode You can control the monitor and camera in Matrix mode. 1. Press [MTX]. 2. Select a monitor number and press [MON]. . Select a camera number and press [CAM]. The selected monitor will play the video of the selected camera. To play the current video on the previous monitor Enter a number for the camera to select. 1. Press the camera number in the Matrix setup screen and press [CAM]. 2.
● . When the screen appears, select a monitor and a camera to connect and specify the dwell time. Using the menu . When camera #1 settings are completed, press and specify the dwell time for camera #2. . When completing the dwell time setting, press . RUN / HOLD RUN/HOLD will run or hold the Auto Select setting that you have made. Press the combination of + to run Auto Select as you set.
menu setting To Access the Main Menu 1. Press a combination of [FUNC] + [SETUP] on the controller. 2. When the setup system screen appears, select a desired menu item. PTZ setting From the PTZ setup screen, you can specify the protocol and baud rate. 1. Press from the setup main screen. 2. Use the direction buttons or joystick to move to a desired menu. . You can change the settings using [ZOOM WIDE] or [ZOOM TELE]. .
DVR Setting ● From the DVR setup screen, you can specify the DVR type and baud rate. menu setting 1. From the setup main screen, press . 2. Use the direction buttons or joystick to select a camera number and specify the DVR type. . Specify the baud rate. . When done, press . . To exit the DVR Setup screen, press or [ESC]. M Before moving to a different page, save your settings. Controller Setting Controller ID You can select RS-485 or RS-422 for the communication system. 1.
menu setting PORT 1 ID You can specify the controller ID if communicating with other devices. 1. Press [Port 1] from the control ID setup screen. 2. Specify the ID and press . PORT 2 ID You can specify the main or sub controller for communications between controllers, and also set the use of matrix and sub list. 1. Press [Port 2] from the control ID setup screen. 2. Use the direction buttons to select a desired item and select a communication system between controllers.
Sub List menu setting 1. Press . ● For a communication system featuring the main and sub controllers, you must set the . 2. Use the direction buttons to select a desired item and configure the settings using [ZOOM WIDE] or [ZOOM TELE]. The MATRIX ID is fixed to . . When done, press . . To exit the screen, press [OK] or [ESC]. Joystick Button Operation You can set the operation for the joystick button. 1. Press the joystick
menu setting Factory Default You can return the current settings to the factory default. 1. Press . 2. Press . The current settings will return to the factory default. . To exit the menu, press . To switch between modules You can switch the position between jog shuttle and joystick from left to right or vice versa. 1. Press . 2. From the Change Module screen that appears, you can switch the position between jog shuttle and joystick. . To exit the screen, press .
Password ● You can enable or disable the controller’s password. menu setting 1. Press the password button. 2. To enable the password, set it to . If not, set it to . . Provide the current password. . To apply the changes, press ; To cancel your setting, press . To change the password You can change the password. 1. Press the password button. 2. Provide the current password. . Provide a new password. .
menu setting Firmware Update You can update the current firmware using the firmware files in the USB memory. To update the controller firmware You can download the latest firmware files and update the controller. 1. Connect the USB memory containing the latest firmware files to the system controller. 2. From the menu setup screen, press . . Press . . From the update screen, press . The update status will be displayed in the progress bar. .
To backup the controller settings 2. Press . . Press . The backup process begins. M Do not disconnect the USB memory or power cable during the backup. Otherwise, it may fail to backup the controller settings. To restore the controller settings If you have set the controller improperly or reset it, you can upload the current settings to a different controller. 1. From the menu setup screen, press . 2. Press . . Press .
menu setting To Check the Controller Information You can check the model name and software version of the system controller. Status Screen You can check the controller status. 1. From the menu setup screen, press . 2. Check the controller status.
appendix Specifications Units to control Baud Rate Compatibility Protocol (PTZ) Protocol (DVR) Protocol (MATRIX) Protocol (RECEIVER) Multilingual Support LCD Display USB Port Video Port Joystick Jog Shuttle Power Operation Temperature Operation Humidity Dimensions Weight appendix Communication System Description ● Item RS-485 / 422 (remote control range: max. 1km) TTL (for controlling the matrix) Max.
appendix Q&A Problem Action • Check if the RS-485 communication cable is connected properly. I cannot communicate with the system controller. • Check if the address of the system controller is specified properly. The USB memory is not recognized properly. • Check if the USB memory works properly. M • For specifying the address, refer to “Controller Setting” from “Menu Setting”. (► page 35) • Use only one USB memory and try again. The LCD panel of the system controller is a consumable part.
GPL/LGPL Software License The software included in this product contains copyrighted software that is licensed under the GPL/ LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CDROM, the cost of physically performing source distribution might be charged.
If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary.
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6.
any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation,write to the Free Software Foundation ; we sometimes make exceptions for this.
You should have received a copy of the GNU General Public License along with this program ; if not, write to the Free Software Foundation, Inc.,51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail.
pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
1. Source Code. The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work. A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
or third parties' legal rights to forbid circumvention of technological measures. 4. Conveying Verbatim Copies.
in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so. 10. A utomatic Licensing of Downstream Recipients.
work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. Limitation of Liability.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code.
Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0.
purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole.
of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.
unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.
DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com SAMSUNG TECHWIN EUROPE LTD.
