To avoid injuries or damage to property, please read the following precautions carefully and use the product accordingly. Failure to follow the instructions marked with this symbol may cause personal injury or even fatality. Failure to follow the instructions marked with this symbol may cause personal injury or damage to the product or property. | Power Related | Installation Related | Cleaning and Use Related | [The images here are for reference only, and are not applicable in all cases (or countries).
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. z There is a danger of electric shock or fire. Always unplug the unit by holding the power plug. Pulling the power cable may damage the inside of it. z There is a danger of fire. Unplug the power plug before cleaning the product. z There is a danger of electric shock or fire.
(rainwater), or in a vehicle. z There is a danger of electric shock or fire. Do not install the product in locations with poor ventilation such as a bookshelf, closet, etc. z An increase in the internal temperature may cause a fire. Do not install on an unstable location, or on a stand smaller than the product. z Make sure to keep the product out of the reach of children. The product may fall and cause personal injury. In case of thunder/lightning, disconnect the power cord from the wall outlet.
Do not insert metal items, such as chopsticks, steel wire, gimlets, or inflammable objects such as matches or paper into the product through the ventilating openings and the PC/Video and power terminals. z This may cause electric shock or fire. If water or an alien substance enters the product, turn the product off, disconnect the power cord from a wall outlet and contact a Service Center. Do not disassemble, or attempt to fix or modify the product.
If the power plug pin or jack is exposed to dust, water or alien substances, clean it thoroughly. z There is a danger of electric shock or fire. When cleaning the product, disconnect the power cord and wipe the product using a soft dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. When not using the product for an extended period of time, disconnect the power plug.
their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. Correct disposal of batteries in this product - Europe only (Applicable in the European Union and other European countries with separate battery return systems.
| Product Features | Product Views | Remote Control | Product Specifications | High Mobility Design - Small Size. - Lightweight. Next Generation Backlight Light Source, LED Lamp - Effective energy saving by using low voltage. - Semi-permanent long lifetime guaranteed. | Product Features | Product Views | Remote Control | Product Specifications | Front/Upper Side 1. Indicators 6.
/ : Use this button to move to or select an item within a menu. - TEMP (Red LED) - STAND BY (Blue LED) ※ Refer to the LED Indications. : Use this button to adjust the volume. 2. Lens cover 7. MENU Button Used to display Menu Screen. 3-1. Adjustable Feet You can adjust the screen position by moving the adjustable feet up and down. 8. SOURCE Button Use this button to select the external device signal. 3-2. The holes to hold the tripod 9. POWER( 4.
LED Indications :Light is On STAND BY :Light is Blinking :Light is Off TEMP Information This state occurs when power is supplied to the projector normally after the POWER button on the projector or the remote control has been pressed. - This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed.
1. VIDEO IN Input port 5. Kensington Lock 2. VIDEO/PC AUDIO IN Input ports 6. PC IN Input port 3. Remote Control Signal Receiver 7. SERVICE Input port 4. POWER Input port 8. Headphone Input port | Product Features | Product Views | Remote Control | Product Specifications | 1. POWER Button ( 2. SOURCE Button 3. MENU Button( 4. Move( 5. VERTICAL KEYSTONE Button ( 6. INSTALL Button 7. STANDARD Button 8. P.SIZE Button 9. QUICK Button ) ) )/ ( 10. MUTE Button ( ) 11.
15. MONITOR Button 16. P.MODE Button 17. MOVIE Button 1. POWER Button ( ) Use this button for turning the product on and off. 2. SOURCE Button Used to check or select the connection status of external devices. 3. MENU Button( ) Used to display Menu Screen. 4. Move( )/ ( )Button Used to move to or select each menu item. 5. VERTICAL KEYSTONE Button ( ) Use this when the screen is displayed in a trapezoid shape. 6. INSTALL Button Used to flip or reverse the projected image. 7.
Design and specifications of the product may be modified without prior notice for better performance. Specifications Model SP-P400 Size 13.97 mm/0.55 inch Resolution 800 x 600 (SVGA) Panel Light Source LED Power Consumption 53 W Voltage DC 14V 4A Power Dimensions (W×H×D) 147.5 x 64.5 x 145.5 mm / 5.8 x 2.5 x 5.7 inch Weight 900 g / 2.0 lb Key Features Brightness 150 ANSI Contrast 1000:1 Screen Size (Diagonal) 20” to 80" Projection Range 0.68 - 2.
MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- VESA, 640 x 350 37.861 85.080 31.500 +/- VESA, 640 x 400 37.861 85.080 31.500 +/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 640 x 480 43.269 85.008 36.000 -/- VESA, 720 x 400 37.927 85.039 35.500 -/+ VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.
| Basic Settings | Connecting the Power | Connecting to video equipment | Installing the Projector Install the projector so that the beam from the projector is perpendicular to the screen. Place the projector so that the lens is at the center of the screen. If the screen is not vertically installed, the picture on the screen may not be a rectangle. Do not install the screen in bright surroundings. If the screen is too bright, the picture on the screen will not be displayed clearly.
Focus Ring Focus the picture on the screen using the Focus Ring. If your product is installed at a location out of the specified projection distance (refer to Screen Size and Projection Distance), the focus cannot be adjusted correctly. Leveling with Adjustable Feet For level placing of the projector, adjust the Adjustable Feet of the projector. You may adjust the level of the projector up to 3 degrees. Depending on the position of the projector, Keystone distortion of image may appear.
Setting up the PC Environment - Check the following items before connecting your PC to your projector. 1. Click the right mouse button on the Windows desktop and click on [Properties]. tab will appear. 2. Click on [Settings] tab and set the by referring to described in the display mode table supported by this projector. You do not have to change setup. 3. Press the [Advanced] button. Another property window will appear. 4.
Process might vary depending on the type of computers or Windows versions. (For example, [Properties] appears instead of [Properties (R)] as shown in 1.) This appliance supports up to 32 bits per pixel in Color quality when it is used as a PC monitor. Projected images may differ from the monitor depending on monitor manufacture or Windows versions. When connecting the projector to a PC, check that PC setup complies to display settings supported by this projector. If not, there may be signal problems.
- Connect [VIDEO IN(yellow)] input port of the projector to the VIDEO (yellow) OUT port of video equipment using the video cable. - Connect the [ ] input port of the projector to the Audio (L), Audio (R) output ports of the external device, such as a DVD, VCR or camcorder using an audio cable. When the connections are all completed, connect both power cables of the projector and the DVD, VCR, or camcorder.
Connect [PC IN] port on the rear side of the projector to the monitor output port of the PC using a PC video cable. When connections are all completed, connect both power codes of the projector and the PC. Connect the [VIDEO/PC AUDIO IN] input port of the projector to the speaker output ports of the PC using an audio cable. This product supports plug and play and therefore, if you use Window XP you do not need to setup the driver on your PC.
Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately.
| Input | Picture | Setup | Option | * Click the Play( Screen Play/Stop You can select a device connected to the projector to display. 1) Video Edit Name ) button in the table below to view the video file. Description Adjustment Source List )/Stop( 2) PC You can edit the names of devices connected to the projector.
* Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Mode )/Stop( Play/Stop Select a screen state which is customized to your projector or change the screen mode as required. 1) Mode - Dynamic Select this if you want the screen quality to be clearer than standard screen quality. - Standard You can comfortably view the projection screen if the surrounding is somewhat bright. - Movie Select this if your surroundings are dark.
8) Color Gamut - Wide : Displays the native color gamut of panel device. - Normal : Normal Color Gamut offers flat and natural color tone. - SMPTE_C : Standardized for Video Equipment by the Society of Motion Picture and Television Engineers. Color Gamut - EBU : Regulations and standards for European Broadcasting Production and technology, standardized by the European Broadcasting Union. 9) Gamma : An image compensation function that controls the settings according to the video properties.
* Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Install )/Stop( To tailor the picture to the installation location, you can invert the projected images vertically/horizontally.
shaking. If the noise is not removed using Fine Adjustment, adjust the frequency to the maximum and then perform Fine Adjustment again. Only activated in the PC environment. 1) Auto Adjustment : Used to adjust frequency and phase of PC screen Auto automatically. Adjustment 2) Coarse : Used to adjust frequency when vertical lines appear on PC screen. 3) Fine : Used to fine tune the PC screen. Coarse 4) Zoom : Used to extend PC screen from the center.
Menu Position You can move Menu Position up/down/left/right. Menu You can set the translucency of menu. Translucency 1) Opaque 2) Low 3) Medium 4) High Menu Display You can set the display time of the menu. Time 1) 5 sec 5) 90 sec 2) 10 sec 6) 120 sec 3) 30 sec 7) Stay On 4) 60 sec Logo If Logo mode is enabled, the Samsung logo is displayed when the projector is turned on. If disabled, it is not displayed.
| Before Contacting Service Personnel | Installation and Connection Symptoms Troubleshooting No Power. z Check the power cable connections. I want to install my projector on z The ceiling installation support is sold separately. Contact your local product distributor. the ceiling. External Source can not be z selected. Be sure that the connection cable(s) (video) is properly connected to the proper port. If the device is not connected properly, it can not be selected.
again. Screen appears in black and white or z bright. As mentioned above, check the adjustment items such as the Brightness, Contrast and Color in the menu. odd color./ screen is too dark or z If you want to restore various settings to their factory defaults, run from the menu. The z See the "3.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority | To clean the exterior and lens of the projector Clean the projector using a soft dry cloth. Do not clean the projector with flammable substances such as benzene, thinners or a wet cloth, as these may cause problems. Do not touch the projector with a nail or any other sharp objects, as this may scratch the surface.
LATIN AMERICA ARGENTINA BRAZIL 0800-333-3733 http://www.samsung.com 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG (726-7864) http://www.samsung.com COLOMBIA 01-8000112112 http://www.samsung.com COSTA RICA 0-800-507-7267 http://www.samsung.com ECUADOR 1-800-10-7267 http://www.samsung.com EL SALVADOR 800-6225 http://www.samsung.com GUATEMALA 1-800-299-0013 http://www.samsung.com HONDURAS 800-7919267 http://www.samsung.com JAMAICA 1-800-234-7267 http://www.
LATVIA 8000-7267 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LUXEMBURG 261 03 710 http://www.samsung.com MACEDONIA 023 207 777 - MONTENEGRO 020 405 888 - NETHERLANDS 0900 - SAMSUNG (0900-7267864) (€ 0,10/Min) http://www.samsung.com NORWAY 815-56 480 http://www.samsung.com POLAND PORTUGAL 0 801 1SAMSUNG (172678) 022 - 607 - 93 - 33 80820 - SAMSUNG (726-7864) RUMANIA http://www.samsung.com http://www.samsung.com http://www.samsung.
HONG KONG http://www.samsung.com/hk (852) 3698-4698 http://www.samsung.com/hk_en/ 3030 8282 INDIA 1800 110011 http://www.samsung.com 1800 3000 8282 1800 266 8282 INDONESIA 0800-112-8888 http://www.samsung.com 021-5699-7777 JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com 1-800-10-SAMSUNG (726-7864) PHILIPPINES 1-800-3-SAMSUNG (726-7864) 1-800-8-SAMSUNG (726-7864) http://www.samsung.com 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.
Gamma Mode Gamma Mode compensates the video signal produced for analog display devices such as a CRT (Cathode Ray Tube) so that the video signal can be clearly displayed on a digital display device. Black Level Black Level sets the light level of the darkest portion of the video signal to match that of the display's black level capability so that users can clearly view dark visuals.
Compression Mode A mode that displays video in a zoomed out format. Contrast Ratio The ratio of the brightest and dimmest points that can be displayed on the screen. Convergence The alignment of the Red, Green and Blue video signals on the projected picture on the screen. Display Size The Display Size is determined by the diagonal length of the LCD panel. DVD (Digital Versatile Disc) Digital media developed to provide the advantages of CD and LD. DVD provides high quality video and audio.
Information in this document is subject to change without notice. ⓒ 2009 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
