NETWORK CAMERA User Manual SNB-7000
Network Camera User Manual Copyright ©2011 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. ● OVERVIEW 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
overview WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK).
Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.
overview Please read the following recommend safety precautions carefully. Do not place this apparatus on an uneven surface. Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. Do not place this apparatus near conductive material. Do not attempt to service this apparatus yourself. Do not place a glass of water on the product. Do not install near any magnetic sources. Do not block any ventilation openings.
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
overview CONTENTS OVERVIEW 3 3 10 10 11 11 12 INSTALLATION & CONNECTION 15 16 15 18 NETWORK CONNECTION AND SETUP 22 22 19 23 24 25 26 27 30 31 33 33 8_ overview Important Safety Instructions Product Features Recomended PC Specifications Recomended SD/SDHC Memory Card Specifications What’s Included At a Glance Mounting the Lens Inserting/Removing an SD Memory Card Memory Card Information (Not Included) Connecting with other Device Connecting the Camera Directly to Local Area Networking Conne
WEB VIEWER 34 44 APPENDIX 72 Connecting to the Camera Login Installing ActiveX Installing Silverlight Runtime Using the Live Screen Playback 44 44 55 61 67 Setup Audio & Video Setup Network Setup Event Setup System Setup 72 76 77 79 81 Specification Product Overview Troubleshooting Open Source Announcement GPL/LGPL Software License English _9 ● OVERVIEW SETUP SCREEN 34 35 36 37 39 42
overview PRODUCT FEATURES • Full HD Video Quality • Multi-Streaming This network camera can display videos in different resolutions and qualities simultaneously using different CODECs. • Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment. • Alarm If an event occurs, the event-related video will be transferred to the email specified by the user or saved to the SD memory, or the event signal will be sent to the Alarm Out port.
• Video Memory : 256MB or higher J If the driver of the video graphic adapter is not installed properly or is not the latest version, the video may not be played properly. • 2GB ~ 32GB • To ensure proper recording of video data, it is recommended you use a memory card that supports at least read/write speed 10Mbps and Class 6. WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package.
overview AT A GLANCE Front Side Item Description Camera Holder (Mount) Holes Used when you mount the camera onto the bracket by fixing the camera holder (mount) adaptor with the bracket. b Auto Iris Lens (Optional) Installed on the lens adaptor. c Auto Iris Lens Connector Used to supply power and output signal to control the iris of the lens. M Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol.
Rear Side ● OVERVIEW AUDIO OUT AUDIO IN SD CARD SD SYSTEM POWER VIDEO 1 2 3 4 5 6 RESET NETWORK 1 : ALARM IN 4 : GND ACT 2 : ALARM OUT 5 : RS-485+ 3 : ALARM COM 6 : RS-485- Item SD Memory Card Compartment b Audio terminal LINK GND AC 24V DC 12V Description Compartment for the SD memory card. AUDIO OUT Terminal for audio output. AUDIO IN Terminal for audio input. ON : A memory card is inserted and operates normally.
overview Item c System, Power, SD Indicators Description POWER ON : While the power is on OFF : If the power is off Resets the camera settings to the default. Press and hold it for about 5 seconds to turn off the system indicator and restart the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled.
installation & connection MOUNTING THE LENS Disconnect the power before proceeding. The C lens and CS lens are not included in the product package. It is recommended that megapixel lens are use on this camera to optimise performance. Mounting the CS lens Turn the optional CS lens clockwise to insert it. CS Lens Mounting the C lens Turn the C mount adaptor clockwise to insert it and do the same with the C lens.
installation & connection Connecting the Auto Iris Lens connector Insert the lens connector into the corresponding hole of the camera. Focusing Turn the lens left or right to control the zoom and focus the lens so that you can view a clear, sharp object. INSERTING/REMOVING AN SD MEMORY CARD J Disconnect the power cable from the camera before inserting the SD memory card. Inserting an SD Memory Card Loosen the screw and open the cover of the SD memory card. Insert the SD card in the arrow direction.
Removing an SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. 1 : ALAR 2 : ALARM IN 4 : GND 3 : ALARM OUT 5 : RS-48 M COM 6 : RS-485+ 5- J Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the slot when released. To remove the SD memory card, set to from and press [Apply ( )].
installation & connection MEMORY CARD INFORMATION (NOT INCLUDED) What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Selecting a memory card that’s suitable for you Your camera supports SD/SDHC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card.
CONNECTING WITH OTHER DEVICE SD ● INSTALLATION & CONNECTION Monitor AUDIO OUT AUDIO IN SD CARD SYSTEM POWER VIDEO RESET 1 2 3 4 5 6 NETWORK 1 : ALARM IN 4 : GND ACT 2 : ALARM OUT 5 : RS-485+ 3 : ALARM COM 6 : RS-485- LINK GND AC 24V DC 12V Power Ethernet Connecting to the monitor Connect the video out port of the camera to the video input port of the monitor. M In the initial installation of the camera, you can connect the camera to the monitor for checking the connection status.
installation & connection Connecting to Audio Input/Output Speaker Microphone PC Microphone Network 123456 1 : ALARM 2 : ALARM IN 4 : GND 3 : ALARM OUT 5 : RS-485 COM 6 : + RS-485- Speaker Amp Amp Microphone 1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifier that the microphone is connected to. 2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker. 3. Check the specifications for audio input. • Audio Codec G.711 PCM.
Alarm I/O Wiring Diagram ALARM IN 1 2 ALARM COM 3 ● INSTALLATION & CONNECTION ALARM OUT (5mA sink) (30VDC 2A, 125VAC 0.5A MAX) GND 4 RXTX+ 5 RXTX- 6 Connecting to the I/O port box Connect the Alarm I/O signal to the corresponding port of the rear port box.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN 1. Launch an Internet browser on the local PC. 2. Enter the IP address of the camera in the address bar of the browser.
CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM External Remote PC Camera DDNS Server (Data Center, KOREA) 1. Use the cross LAN cable to connect the network cable directly to your PC. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3. Use the Internet browser to connect to the camera. 4. Move to [Setup] page. 5. Move to [Network] – [DDNS] and configure the DDNS settings. 6.
network connection and setup CONNECTING THE CAMERA DIRECTLY TO A PPPoE MODEM INTERNET PPPoE Modem External Remote PC Camera DDNS Server (Data Center, KOREA) 1. Use the cross LAN cable to connect the network cable directly to your PC. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3. Use the Internet browser to connect to the camera. 4. Move to [Setup] page. 5.
CONNECTING THE CAMERA TO A BROADBAND ROUTER WITH THE PPPoE/CABLE MODEM This is for a small network environment such as homes, SOHO and ordinary shops. INTERNET Camera Broadband Router PPPoE or Cable Modem PPPoE or Cable Modem External Remote PC Local PC DDNS Server (Data Center, KOREA) Configuring the network settings of the local PC connected to a Broadband Router Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions below.
network connection and setup BUTTONS USED IN IP INSTALLER Item Description Device Name Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search. b Mode Displays either or for the current network connection status. c MAC(Ethernet) Address Ethernet address for the connected camera. Click the column to sort the list by Ethernet address.
Item m M URL DDNS URL address enabling access from the external Internet. However, this will be replaced with the of the camera if DDNS registration has failed. IPv4 Scans for cameras with the IPv4 setting. IPv6 Scans for cameras with the IPv6 setting. Search Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked. Auto Set The IP Installer automatically configures the network settings.
network connection and setup 3. In the
pane, provide the necessary information. • MAC (Ethernet) Address : The MAC (Ethernet) address of the applicable camera will be set automatically so you don't need to input it manually. M You can configure the static IP settings only if the DHCP checkbox is unchecked. If using a Broadband Router • IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.6. Click [OK]. Manual network setup will be completed. 7. When the manual setup including IP is completed, the camera will restart. If the Broadband Router has more than one camera connected Category Camera #1 Camera #2 IP related settings IP Address Subnet Mask Gateway 192.168.1.100 255.255.255.0 192.168.1.1 192.168.1.101 255.255.255.0 192.168.1.
network connection and setup 3. Enter the password. This is the login password for the “admin” user who accesses the camera. The default password is “4321”. 4. Click [OK]. Auto network setup will be completed.
PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. ● NETWORK CONNECTION AND SETUP Manual Port Range Forwarding 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
network connection and setup Setting up Port Range Forward for several network cameras When several network cameras are connected to one Broadband Router device, you should forward the TCP 943 port of the router to the TCP 943 port of a connected camera. J If you don't set properly the TCP 943 port of the router, you cannot get any video stream from the web page of the camera. • TCP 943 port is a port for the Silverlight policy server of a camera.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 2. Double-click a camera to access. The Internet browser starts and connects to the camera. M Access to the camera can also be gained by typing the camera's IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000 :0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
To check the DDNS address Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP when you try to access the device. To add the IP address to the server, visit www.samsungipolis.com and register your device, and set the DDNS option to before providing the host name for the DDNS server. LOGIN The default user ID is “admin”, and the default password is “4321”. 1. Enter “admin” in the input box. 2.
web viewer INSTALLING ACTIVEX If connecting to a camera for the first time, you will see the installation message. Then, install the required ActiveX to access the camera and control the video from it in real time. 1. When accessing the start screen of the monitoring page, click the yellow warning message in the top of the page. 2. Click . 3. The security warning popup appears, click [Install]. 4.
INSTALLING SILVERLIGHT RUNTIME If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will be redirected to the Silverlight Runtime installation page automatically when accessing the web viewer. ● WEB VIEWER 1. Click . 2. When the file download dialog pops up, click . 3. When the download is completed, click . 4. The Silverlight Runtime installation page will be displayed. to proceed with the installation.
web viewer 5. When done, click . 6. Close and restart the web browser, and try to access the Web Viewer. When Silverlight Runtime is properly installed, you will see the Live screen.
USING THE LIVE SCREEN ● WEB VIEWER Item Description Monitoring Move to the monitoring screen. b Playback Switch to the monitoring screen that plays recording data in the SD memory. c Setup Move to the Setup screen. Viewer Screen Displays the Live video on the screen. Alarm Output Activate the Alarm Out port. Audio Display the audio Listen and Talk toggle button on the screen. Hide the alarm indicator Hides the alarm indicator near the border of the viewer screen.
web viewer Item Description Control the pan/tilt/zoom operations of the camera. PTZ Digital zoom You can use the mouse wheel to activate the digital zooming. Screen Optimization, Full Screen Adjust the screen to the optimal size, and display the Full Screen icon on the Live screen. Capture Saves the snapshot as an image file in the .bmp format. The pan/tilt operations will be enabled only if the camera is connected to a pan/tilt-compliant receiver.
To toggle the audio sound 1. Click the [Audio ( )] button. The corresponding button will be displayed in the Viewer. ● WEB VIEWER 2. Click the button to listen to / mute the sound as you wish. This button operates as a toggle button. To toggle the microphone sound )] button. 1. Click the [Mic ( The corresponding button will be displayed in the Viewer. J “Cannot find audio recording device” message appears if there is no Microphone. 2. Click the button to start / stop talking.
web viewer To control the PTZ 1. Press the [PTZ ( )] button. 2. When the PTZ button bar appears on the screen, use the direction buttons to adjust the camera angle, zoom factor or focus to your preference. M For further details on PTZ use, refer to “External PTZ setup”. (page 53) PLAYBACK 1. Click the [Playback ( )] button. 2. Specify the start time and end time of your search. 3. Select a search type. )] button. 4. Click the [Search ( The search results will be displayed in the list.
5. Select a data item to play in the search list. 6. Click the [Play ( )] button. M ● WEB VIEWER 7. To stop playing the video, click [Stop )]. ( To return to the search screen, click [Exit ( )]. The Silverlight web viewer can [Playback] an image in resolutions of up to 640x480. However, the MJPEG codec is available for all resolutions. To check time information of the playing video 1. Click the [About ( )] button. 2. Date and time information appears on the screen.
setup screen SETUP You can configure the audio & video, network, event and system settings of the camera via the network. 1. In the Live screen, click [Setup ( )]. 2. The Setup screen appears. AUDIO & VIDEO SETUP Video profile 1. From the Setup menu, select the )> tab.
To add a video profile You can add as many codecs as necessary so that a variety of profiles can be applied according to the recording condition. 1. Select a profile number. 3. Specify the conditions under which the codec will be applied. 4. Specify the details of the selected codec including resolution and frame rate. • Resolution : Set the video size of the H.264 and MJPEG files. • Framerate : Specify the frame rate. • Compression : Specify the compression rate of the video.
setup screen What is GOP size? GOP(Group of Pictures) is a set of video frames for H.264 compression, indicating a collection of frames from the initial I-Frame (key frame) to the next I-Frame. GOP consists of 2 kinds of frames: I-Frame and P-Frame. I-Frame is the basic frame for the compression, also known as Key Frame, which contains one complete image data. P-Frame contains only the data that has changed from the preceding I-Frame. You can specify a value between 1 and 15 for the H.264 CODEC.
3. Provide a name and press [OK]. 4. If you want to delete an area, select that area in the list and press [Delete )]. ( 5. When done, click [Apply ( )]. ● SETUP SCREEN Audio setup You can configure the I/O settings of the audio source from the camera. 1. From the Setup menu, select the
setup screen SSDR (Samsung Super Dynamic Range) Setup In a scene where the difference between bright and dark is severe, you can increase the brightness of the dark area alone to regulate the overall brightness. 1. Select . 2. Set to . 3. Configure the and settings as necessary. • Level : Adjust the level of the dynamic range. • D-Range : Select the amplitude area of the dynamic range.
BLC Setup You can specify a desired area on the video manually and set the area to be displayed more clearly. 1. Select . ● SETUP SCREEN 2. Set to . 3. Set . You can change the level to adjust the brightness of the monitoring area. 4. Set the levels to specify the target area.
setup screen WDR Setup It displays a sharp image of the objects in a scene where both bright and dark areas exist. 1. Select . 2. Set to . 3. Specify the . M WDR is available only if is set to <2-Megapixel>. If WDR mode is activated, you cannot change the shutter type. Exposure Setup You can adjust the exposure level of the camera. 1. Select . 2. Select each item and set it properly. • Brightness : Adjust the screen brightness.
Special Setup 1. Select . 2. Select each item and set it properly. • Day & night : You can switch the mode to adjust the black and white level as well as the colors. - Color : Always displays the video in colors. - B/W : Always displays the video in black and white. - Auto : Displays in color mode during normal daytime and switches to black and white mode in a low contrast scene at night. If you set the AGC mode to OFF from , the AUTO DAY/NIGHT mode will be disabled accordingly.
setup screen OSD Setup 1. Select . 2. Select each item and set it properly. • Camera title : Use alphanumeric characters in the list and enter a desired title in the bottom input line. You can enter up to 15 characters for the title. • Camera title position x, y : Specify the coordinates where the camera title is displayed. Time OSD Setup 1. Select
4. Select a quality and detection sensitivity for the ROI area. 5. If manually specifying the ROI area, select a desired area with the mouse pointer and drag it as much as you want. You can specify up to 5 distinct areas. 7. When done, click [Apply ( J ]. )]. The Smart codec will not be active if it is set to in
setup screen To add a preset 1) Select the preset number to add. 2) Set the name for the preset. 3) Press the [ ] button. To delete a preset 1) Select the preset number to delete. 2) Press the [ ] button. To move a preset 1) Select a preset number that you want to move. 2) Press the [ ] button. 6. Specify the serial port. You can set the RS-485 communication mode for pan/tilt-compliant receiver that is connected to the network camera.
NETWORK SETUP Interface 2. Click . 3. Set the and as necessary. • IP type : Select an IP connection type. - Manual : Specify the IP address, Subnet mask, Gateway, DNS1, and DNS2. - DHCP : Specify the DNS1 and DNS2. - PPPoE : Specify the DNS1, DNS2, Name and Password. If you set it to , you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually. • • • • • • • MAC address : Shows the MAC address. IP address : Displays the current IP address.
setup screen Port 1. From the Setup menu, select the tab. 2. Click . 3. Type in each item in the Port menu as necessary. Neither the port range between 0 and 1023 nor port 3702 is available. • HTTP port : HTTP port used to access the camera via the web browser. The default is 80(TCP). • VNP port : Set a port used to transfer video signals with the Samsung protocols. • RTSP port : Used to transfer videos in the RTSP mode; the default is 554.
5. When done, click [Apply ( )]. Registering with DDNS To register your product with the Samsung DDNS 1. Visit the iPOLiS web site(www. samsungipolis.com) and sign in with a registered account. 2. From the top menu bar, select - . 3. Click [PRODUCT REGISTRATION]. 4. Enter the product domain. You must perform the duplicate check for the domain that you entered.
setup screen 5. Select a and specify the . 6. Specify the product location with a description if necessary. 7. Click [REGISTRATION]. The product will be added to the product list that you can check. To connect to the Samsung DDNS in camera setup 1. From the DDNS setup page, set to . 2. Provide the that you registered product domain with the DDNS site. )]. 3.
IP filtering You can create a list of IPs that you want to grant or deny access to them. 1. From the Setup menu, select the tab. ● SETUP SCREEN 2. Click . 3. Select . • Deny : If selecting this, access from those IPs that are added to the filtering will be restricted. • Allow : If selecting this, access from only those IPs that are added to the filtering will be accepted. 4. Provide the IP that you want to grant or deny access from.
setup screen Installing the certificate 1. Enter the certificate name. 2. Select the certificate file to be installed and certificate key, and click [Install ( button. )] Deleting the certificate 1. Click [Delete ( )] button. 802.1x When connecting network, you can choose whether using 802.1x protocol, and then install the certification. 1. From the Setup menu, select the tab. 2. Click <802.1x>. 3. Set the . • Enable IEEE 802.
EVENT SETUP FTP / E-mail 1. From the Setup menu, select the tab. 2. Click . 3. Select or and enter / select a desired value. • FTP configuration - Server address : Enter the IP address of the FTP server that you transfer the alarm images to. - User ID : Enter the user ID with which you will log in to the FTP server. - Password : Enter the user account password for logging into the FTP server.
setup screen - Sender : Enter the address of the email sender. If the sender address is incorrect, the email from the sender may be classified as SPAM by the email server and thus may not be sent. - Subject : Enter a subject for your email. - Body : Provide the text for the massage. Attach the alarm images to the email that you are preparing. 4. When done, click [Apply ( )].
4. When done, click [Apply ( )]. Alarm input You can set the alarm input type, activation time, and operation mode. 1. From the Setup menu, select the tab. 2. Click . 3. Specify an input device. • Type - Normal Open : It is normally open, but if it is closed, an alarm will be triggered. - Normal Close : It is normally closed, but if it is open, an alarm will be triggered. 4. Specify the . • Always : Always check if an alarm occurs.
setup screen 5. Specify an operation that will perform if an alarm occurs. • Alarm output : Select whether to set the alarm output if an alarm is incoming, and specify the alarm output time. • E-mail sending : Specify the use of email transfer in the alarm input setup. • FTP sending : Specify the use of FTP transfer in the alarm input setup. • Record : Specify the use of recording in the alarm input setup. • Goto Preset : Moves to the specified preset location when setting the alarm input.
J If you are controlling the Pan/Tilt/Zoom operation or fitting the focus of the camera, the motion sensor may not work. If camera is capturing a close object, the motion detection capability may degrade. In the following case, Motion detection function which is initially set may be worked abnormally. The object color or brightness is similar to the background. Multiple movements continue occurring at random due to a scene change or other reasons. A fixed object continues moving in the same position.
setup screen Network disconnect You can perform the saving/relay/preset operation after receiving an event of a physically disconnected network. 1. From the Setup menu, select the tab. 2. Click . 3. Specify the use of “Network disconnect”. 4. Specify the activation time and activation condition. For more information about and , refer to “Alarm input”. (page 63) 5. When done, click [Apply ( 66_ setup screen )].
SYSTEM SETUP Product information 2. Click . 3. Check the camera information, or provide details according to your network environment. • Device name : Provide a device name that will be displayed on the Live screen. • Location : Specify the location where the camera is installed. • Description : Provide detailed information about the camera location. • Memo : Provide an explanation about the camera for better understanding.
setup screen • System time setup : Specify the time and date that will be applied to your system. - Manual : Specify the time manually. - Synchronize with NTP server : Sync with the time of the specified server address. - Synchronize with PC viewer : Synchronize the time with the connected PC. 4. When done, click [Apply ( J )]. If you select the , the standard timezone should be set the same as the current timezone in PC. User 1.
Upgrade / Reboot 1. From the Setup menu, select the tab. 2. Click . • Configuration backup & Restore : Backs up the current system settings before performing the restoration process. The system is automatically restarts after backup or restoration. • Restart : Restarts the system. To perform the upgrade 1. Click [Upgrade]. 2. Click [Browse] and specify a file to upgrade. 3. Click [Send]. 4. The “Upgrade” dialog appears where the progression will be shown in the bottom.
setup screen To save the current settings and restore the backup settings 1. Click [Backup]. The Save As dialog should appear. 2. Specify the backup path with a proper file name, and click [Save]. The backup file will be saved to the specified path in the format of “.bin”. 3. To restore the backup settings, click [Restore]. 4. Select a backup file and click [Open]. M If you perform the backup or restoration, the web browser will be closed and the camera will reboots.
Log You can check the system log or event log. 1. From the Setup menu, select the tab. ● SETUP SCREEN 2. Click . 3. Select a log type. • Syslog : You can check the system logs where any system changes are recorded including the time information. • Evtlog : You can check the event logs including the time information. 4. From the right log list, select an item to search for. • If you select in the top left dropdown list, all logs for the applicable log type will be displayed. 5.
appendix SPECIFICATION Items Description Imaging Device 1/2.8" 3M PS CMOS Total Pixels 2,144(H) X 1,588(V) Effective Pixels 2,096(H) X 1,561(V) Scanning System Progressive Video Min. Illumination Color : 1 Lux (F1.2, 50IRE), 0.017Lux (Sens-up 60X) B/W : 0.08 Lux (F1.2, 50IRE), 0.001Lux (Sens-up 60X) S / N Ratio 50dB Video Out CVBS : 1.0 Vp-p / 75Ω composite, 704x480(N), 704x576(P), for installation Focal Length (Zoom Ratio) - Max. Aperture Ratio - Angular Field of View - Min.
Items Off / On (Displayed up to 15 characters) Day & Night Auto (ICR) / Color / B/W / Externel B/W Backlight Compensation Off / BLC / HLC Wide Dynamic Range Off / On (* 2M mode only) Contrast Enhancement SSDR (Samsung Super Dynamic Range) (Off / On) Digital Noise Reduction SSNRIII (2D+3D Noise Filter) (Off / On) Digital Image Stabilization - Motion Detection Off / On (4 programmable zones) Privacy Masking Off / On (1ea 4 Point Polygonal + 16ea Rectangular zones) Sens-up (Frame Integration)
appendix Items Description Ethernet RJ-45 (10/100BASE-T) Video Compression Format H.264, MJPEG Resolution <2M Mode> 800x600, 800x450, 640x480, 640x360, 320x240, 320x180, 1280x1024, 1024x768, 1280x960, 1920x1080 <3M Mode> 800x600, 800x450, 640x480, 640x360, 320x240, 320x180, 1280x1024, 1024x768, 1280x960, 1920x1080, 1600x1200, 2048x1536 ● For MJPEG <2M Mode> 800x600, 800x450, 640x480, 640x360, 320x240, 320x180 : 30 fps 1280x1024, 1024x768, 1280x960 : 15 fps 1920x1080 : 10 fps Network Max.
Items Description IPv4, IPv6 Protocol TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP, HTTPS, SSL, DHCP, PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS HTTPS(SSL) Login Authentication Digest Login Authentication Security IP Address Filtering User access Log 802.1x Authentication Network Streaming Method Unicast / Multicast Max.
appendix PRODUCT OVERVIEW ]W OYUZ]IP ^Y OYU_ZIP XZ_U] O\U[\IP XZ]U_ O\UZ_IP 76_ appendix
TROUBLESHOOTING PROBLEM SOLUTION y Check to make sure that all network cables have been connected properly. I can’t access the camera from a web browser. y If connected using DHCP, verify that the camera is able to acquire dynamic IP addresses without any problem. y If connected using a DDNS URL, verify that the MAC address has been properly entered. y If the camera is connected to a Broadband Router, verify that port forwarding is properly configured.
appendix PROBLEM SOLUTION Cannot record into the SD memory y Check if the memory card is defective. card. y Check if the write protection tab of the memory card is set to “LOCK”. y Check if the memory card is defective. SD memory indicator does not turn on even when the SD memory y Check if the is checked in card is inserted. menu. A SD memory card is inserted but the product does not recognize it. Cannot format the SD memory card.
OPEN SOURCE ANNOUNCEMENT Some software components of this product incorporate source code covered under the BSD license as follows. Component Name License License URL lighttpd 1.4.25 librtp 1.20 BSD 2.0 BSD 1.0 http://www.opensource.org/licenses/bsd-license.html lighttpd is a secure, fast, compliant, and very flexible web-server that has been optimized for high-performance environments. It has a very low memory footprint compared to other webservers and takes care of cpu-load.
Copyright (c) 1998-2001 University College London All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met : 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
GPL/LGPL SOFTWARE LICENSE The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.
based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.
a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10.
WARRANTY ; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program ; if not, write to the Free Software Foundation, Inc.,51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail.
or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License.
3. Protecting Users' Legal Rights From Anti-Circumvention Law. No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11). from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement).
work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such. 14. Revised Versions of this License. The Free Software Foundation may publish revised and/ or new versions of the GNU General Public License from time to time.
USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it.
Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing nonfree programs.
is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1.
it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4.
1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine readable “ work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.
it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10.
later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission.
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail.
Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@ cryptsoft. com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft. com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com www.samsungipolis.com SAMSUNG TECHWIN EUROPE LTD.
