NETWORK CAMERA User Manual SNB-3000(P)
overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury. 6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center.
overview CAUTION 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4.
FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. IC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference.-Causing Equipment Regulations of ICES-003.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
CONTENTS OVERVIEW 2 6 9 9 INSTALLATION & CONNECTION 14 15 14 16 18 Mounting the lens Inserting/Removing an SD Memory Card Memory Card Information (not included) Connecting with other Device CAMERA SETUP 22 23 23 24 28 29 30 How to use the menu key Main Menu Profile Camera Setup Privacy Zone Others System Info NETWORK CONNECTION AND SETUP 31 31 32 Connecting the Camera to an Broadband Router with the xDSL/Cable Modem Connecting the Camera to an Broadband Router with Local Area Networking Connec
overview WEB VIEWER 42 SETUP SCREEN 50 APPENDIX 69 8_ overview 42 43 44 45 46 49 Connecting to the Camera Login Installing ActiveX Using the Live Screen Backup Using the SD Search Viewer Screen 50 50 55 58 59 68 Accessing the Setup Screen Default Setup System Setup Overlay Setup Event Setup Network Setup 69 70 72 76 82 88 90 Profile Terminology Specifications Frame Rate (NTSC) Frame Rate (PAL) Troubleshooting GPL/LGPL Software License
PRODUCT FEATURES PRECAUTIONS – INSTALLATION AND USE y Do not bend or drop the SD memory card. y Do not store or use the SD memory card in a high temperature, high humidity or dusty place. y Be careful not to apply foreign substances on the terminals of SD memory card. y In case of cleaning terminals, wipe gently with a soft cloth. y Before ejecting the SD memory card, release the checkbox in and press [Apply] button.
overview y y y y Web Browser : Internet Explorer 6.0 or higher Video Card : Radeon, Nvidia Video Memory: 128MB DirectX 8.1 or higher Compatible Broadband Routers y Linksys / D-Link / Netgear Compatible PoE Switches y Linksys SRW224G4P / D-Link DES-1316 / SMC SMCPWR-INJ3 WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package.
AT A GLANCE Front Side ● OVERVIEW Item M Description Camera Holder (Mount) Holes Used when you mount the camera onto the bracket by fixing the camera holder (mount) adaptor with the bracket. Auto Iris Lens (Optional) Installed on the lens adaptor. Auto Iris Lens Connector Used to supply power and output signal to control the iris of the lens. Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol.
overview Rear Side AUDIO OUT AUDIO IN SD CARD SD SYSTEM POWER VIDEO 1 2 3 4 5 1,2 : ALARM IN 1,2 3 : GND 4,5 : ALARM OUT 1,2 Item SD Memory Card Compartment RESET NETWORK ACT LINK GND AC 24V DC 12V Description Compartment for the SD memory card. AUDIO OUT Terminal for audio output. AUDIO IN Terminal for audio input. SD ON: A memory card is inserted and operates normally. Flashing: Failed to record, insufficient space, or inserted abnormally.
Reset Button Resets the camera settings to the default. Press and hold it for about 3 seconds to turn off the system indicator and restart the system. Power Port Used to plug the power cable. GND Used for earth-grounding. Network Port Used to connect to the Network cable. Video Out Port Used to connect the alarm input signal. GND Used for earth-grounding. ALARM OUT 1,2 Used to connect the alarm output signal.
installation & connection MOUNTING THE LENS Disconnect the power before proceeding. Mounting the CS lens Turn the optional CS lens clockwise to insert it. CS Lens Mounting the C lens Turn the C mount adaptor clockwise to insert it and do the same with the C lens.
Connecting the Auto Iris Lens connector Insert the lens connector into the corresponding hole of the camera. Turn the lens left or right to control the zoom and focus the lens so that you can view a clear, sharp object. INSERTING/REMOVING AN SD MEMORY CARD Inserting an SD Memory Card Push the SD memory card in the direction of the arrow shown in the diagram. J Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the SD memory card.
installation & connection Removing an SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. J Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the slot when released. Before ejecting the SD memory card, release the checkbox in and press [Apply] button.
Memory Card Use SD and SDHC memory cards feature a switch that disables writing data on to the media. Having this switch to the Lock position will prevent accidental deletion of data stored in the memory card but at the same time will also prevent you from writing data on to the media.
installation & connection CONNECTING WITH OTHER DEVICE Monitor AUDIO OUT AUDIO IN SD CARD SD SYSTEM POWER VIDEO RESET 1 2 3 4 5 1,2 : ALARM IN 1,2 3 : GND 4,5 : ALARM OUT 1,2 NETWORK ACT LINK GND AC 24V DC 12V Power Network Connecting to the monitor Connect the [VIDEO] port of the camera to the video input port of the monitor. Network Connection Connect the Network cable to the local network or to the Internet.
Connecting to Audio Input/Output LINE-IN Speaker Pre-Amp LINE-OUT Pre-Amp Microphone 1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifier that the microphone is connected to. y Direct Mic Connection : Set Audio Input Gain high (10). (Refer to page 51) y Line Out Connection : Set Audio Input Gain low (1). (Refer to page 51) 2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
installation & connection Audio I/O Block Diagram PC Network Microphone Microphone Speaker Pre-Amp Pre-Amp y Audio Codec G.711 PCM. μ-law 64kbps 8kHz sampling y Full duplex Audio y Audio in Used for mono signal line input (Max.2.4 Vpp) y Audio out Used for mono signal line output (Max.2.
Connecting to the I/O port box Connect the Alarm I/O signal to the corresponding port of the rear port box. AUDIO OUT AUDIO IN 1 2 3 4 5 SD CARD SD SYSTEM POWER RESET NETWORK 1 2 3 4 5 1,2 : ALARM IN 1,2 3 : GND 4,5 : ALARM OUT 1,2 1,2 : ALARM IN 1,2 3 : GND 4,5 : ALARM OUT 1,2 ACT LINK GND AC 24V DC 12V y ALARM IN 1, 2 : Used to connect the alarm input signal. y GND : Used for earth-grounding. y ALARM OUT 1, 2 : Used to connect the alarm output signal.
camera setup You can configure the camera settings using the Web Viewer. M For accessing the Web Viewer, refer to "Network Connection and Setup". (page 31) HOW TO USE THE MENU KEY Follow the steps below if you run the Web Viewer for setting the menus. 1. Launch the Web Viewer. 2. From the [Camera OSD] menu in the left pane, click [Menu]. The screen appears. 3. Click the Up/Down (▲▼) buttons to move to a desired item. 4.
MAIN MENU You can configure the camera settings to your preference. ** MAIN MENU ** PROFILE CAMERA SET PRIVACY ZONE OTHER SET SYSTEM INFO PROFILE You can select one from the pre-determined modes as appropriate to your specific camera installation environment. Your selection on each item in PROFILE will affect all other settings of the camera. For the setting, refer to "PROFILE". (page 69) For selecting and saving each menu item, refer to "How to use the menu key".
camera setup CAMERA SETUP You can configure the general settings of the camera module. For selecting and saving each menu item, refer to "How to use the menu key". (page 22) CAMERA ID Provide the ID and position for a camera that displays on the screen. 1. Select - . 2. Use the four direction (▲▼◄ ►) buttons to select a desired character. In the lower input box of the screen, the selected character will be entered.
MOTION ◄ CAMERA SET CAMERA ID IRIS MOTION DNR SHUTTER SENS-UP FLICKERLESS XDR DIS ► ON ALC (F.FAST) (F.FAST)----MID OFF AUTO X4 OFF MID OFF DNR Reduces the noise on the screen. This is useful, especially for a noisy screen. Set it to , you can specify the level. SHUTTER The SHUTTER menu is used to set the fixed fast electronic shutter or auto fast electronic shutter.
camera setup DAY/NIGHT You can specify a recording mode according to the scene. 1. Select - . 2. Select a screen transition mode according to the illumination, and set options as appropriate. y DAY : Fixed to DAY mode, regardless of the scene. y NIGHT : Fixed to NIGHT mode, regardless of the scene. If BURST is set to , the burst signal will output. y AUTO : According to the luminance, this will switch DAY to NIGHT mode, or vice versa.
You can set the R-GAIN, and B-GAIN value only in AWC mode. DIGITAL ZOOM You can set the digital zoom factor and position. When the zoom factor and position are defined, the digital zoom function will operate. If you set the digital zoom to a larger factor than the actual enlargement for compensation, the DIS function will be disabled. DETAIL You can adjust the vertical and horizontal sharpness, respectively. AGC COLOR SUP This will adjust the color scheme according to the AGC value.
camera setup PRIVACY ZONE You can set up to 12 privacy zones that will be hided for privacy of the subject when recording. For selecting and saving each menu item, refer to "How to use the menu key". (page 22) ZONE SETUP 1. Select - . 2. Use the four direction (▲▼◄ ►) buttons to select a desired number. The Zone setup screen appears. 3. Select the . Specify the pixel unit level for the POSITION setting. 4. Select . You will see dots on the screen.
OTHERS You can reset the camera, or select the OSD font color to your preference. For selecting and saving each menu item, refer to "How to use the menu key". (page 22) LANGUAGE Select your language by using the left and right keys. ◄ OTHER SET ► LANGUAGE ENGLISH FACTORY DEFAULTS OSD COLOR BW FACTORY DEFAULT 1. Select - - . The FACTORY DEFAULTS setup screen appears. 2. Select . All the settings will be restored to the factory default.
camera setup SYSTEM INFO You can check the system information. For selecting and saving each menu item, refer to "How to use the menu key". (page 22) 1. Select - . 2. The current system information is displayed. M The camera type may different, depend on the video signal. 30_ camera setup ◄ SYSTEM INFO TYPE CAMERA VER. ► 3_IPV_P v2.
network connection and setup You can set up the network settings according to your network configurations. M Before installing or while using this program, visit the Samsung website www.samsungsecurity.com and download and upgrade with the latest S/W version available. This is for a small network environment such as homes, SOHO and ordinary shops.
network connection and setup ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1 IP address: 192.168.xxx.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.xxx.1 M For the address of the Broadband Router, refer to the product’s documentation.
M For the address of the Broadband Router, refer to the product’s documentation. CONNECTING THE CAMERA DIRECTLY TO A DHCPBASED XDSL/CABLE MODEM INTERNET kzsG❄⏈ xDSL or jG⯜⒴ Cable Modem 㞬⺴G㠄ᷝGwj External Remote PC SNB-3000 kkuzG㉐ⶸ DDNS Server OkGjSGrvylhP (Data Center, KOREA) Setting the Broadband Router This is enabled for a modem using DHCP. 1. Set the Static or Dynamic IP address. (pages 36~39) 2. Launch an Internet browser on the local PC connected to the Broadband Router. 3.
network connection and setup 4. When the Broadband Router is connected, the login window appears and prompts you to enter the password. For the login IP and the password, refer to the Broadband Router’s documentation. 5. When done, you will see the setup window of the Broadband Router. In the setup menu, select “Automatic Configuration-DHCP” for Internet Connection Type. For the menu location of Internet Connection Type or DHCP selection, refer to the Broadband Router’s documentation. 6.
IP ADDRESS SETUP ● NETWORK CONNECTION AND SETUP Buttons used in IP Installer Item Description Device Name Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search. Mode Displays either or for the current network connection status. MAC(Ethernet) Address Ethernet address for the connected camera. Click the column to sort the list by Ethernet address.
network connection and setup IPv4 Scans for cameras with the IPv4 setting. IPv6 Scans for cameras with the IPv6 setting. Search Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked. Auto Set will automatically configure the network settings for you. Manual Set You should configure the network settings manually. Exit Exits the IP Installer program.
If using an Broadband Router : If not using an Broadband Router : For setting , , and , contact your network administrator. M The values of VNP, TCP, UDP, Upload, and Multicast ports can not be changed manually, and will be adjusted according to the HTTP port value. 4. In the pane, provide necessary information. y HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. Use the spin button to change the HTTP Port value.
network connection and setup If the Broadband Router has more than one camera connected Configure the IP related settings and the Port related settings distinctly with each other. Category IP related settings IP Address Subnet Mask Gateway HTTP Port VNP Port TCP Port Port related settings UDP Port Upload Port Multicast Port M Camera #1 Camera #2 192.168.1.200 255.255.255.0 192.168.1.1 192.168.1.201 255.255.255.0 192.168.1.
3. Enter the password. This is the login password for the "admin" user who accesses the camera. The default password is "4321". 4. Click [OK]. Auto network setup will be completed.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed an Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. Manual Port Range Forwarding 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Launch . It will scan for connected cameras and display a list of them. M You can also access the camera in such way you type the IP address of the found camera in the address bar of the Internet browser. CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET As a remote PC can not directly access , you should access the camera in the Broadband Router network using DDNS URL of the camera. 1.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.200 http://192.168.1.200 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000 :0000:ffff:1111] If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar.
To check the DDNS address J The above mentioned addresses are simply examples; do not use any of these for connecting purposes. LOGIN The default user ID is "admin", and the default password is "4321". 1. Enter "admin" in the input box. 2. Enter "4321" in the input box. If the password is changed, enter the changed password instead. 3. Click [OK]. If you have logged in successfully, you will the Live Viewer screen.
web viewer INSTALLING ACTIVEX If connecting to a camera for the first time, you will see the installation message. Then, install the required ActiveX to access the camera and control the video from it in real time. For Windows XP Service Pack 2 users 1. Click the installation message that pops up when you first access the camera. 2. Click . 3. The security warning popup appears, click [Install]. 4.
USING THE LIVE SCREEN ● WEB VIEWER Item Description SD Search Moves to the screen for searching event images from the SD card. Setup Move to the Setup screen. About You can check the firmware version, serial number and manufacturer information. Reset Alarm Resets the Alarm icon. (Alarm and Intelligent Video Analysis icons will disappear.) Capture Saves the snapshot as an image file in the .jpeg or .bmp format. Print Prints out the current image.
web viewer Camera OSD Used to retrieve and customize the Camera Setup menu. For selecting and saving each menu item, refer to "How to use the menu key". (page 22) Audio Check the Listen or Speak check box for Audio. Viewer Screen Displays the Live video on the screen. BACKUP You can capture, print out, and save the snapshot in the specified path. To capture the snapshot 1. Click [ ] on the scene to capture. The Capture dialog should appear. 2. Click [OK].
To print out the screenshot 1. Click [ ] on the scene to print out. The Print setup dialog appears. 2. Specify the name of the printer connected, and click [OK]. ● WEB VIEWER To record a video 1. Click [ ] on the scene to record. 2. You will see the Save AVI dialog; provide the necessary information. y Save path : You can change the default saving path. y File name : You can change the default file name.
web viewer y Default file path - Windows XP : C:\Program Files\Samsung\SNB-3000\VideoClip\Live If you want to change the path, click [Set path ( )] and specify a path. - Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\ SNB-3000\VideoClip\Live On the Windows Vista, Windows 7 system, the path to save is fixed. y The screenshot file will be named automatically in the format of . ex) 192.168.0.200_60001_20090903_112334_00 y If you want to play an .
USING THE SD SEARCH VIEWER SCREEN 1. Click tab in the Live screen. 2. The SD Search Screen appears. SD Search Viewer Screen layout ● WEB VIEWER Name Function and description Thumbnail Size The thumbnail images are displayed based on the selected size. Date You can select the desired date to search for events generated. Schedule You can select the desired time to search the schedule events. Alarm input You can select the desired time to search the alarm events.
setup screen ACCESSING THE SETUP SCREEN You can configure the default setting, system, overlay, event and network related settings, and change them as necessary. 1. In the Live screen, click the tab. 2. The Setup screen appears. DEFAULT SETUP To configure the video & audio settings You can set the video resolution, quality, CODEC and audio input/output settings. 1. Select -
y y y y y y Target bitrate : Transfers video signal at a specified bit rate. Compression : Adjust the compression rate from 5 through 100 by 5. Encode priority : Set the video transfer method to Frame rate or Quality. GOP* size : Select a GOP size between 5 and 15. Deblock : This will soften the edges between macro blocks. De-Interlace : You can reduce the grid noise by using the de-interlacing function. Only available if MPEG4 resolution is set to 4CIF.
setup screen - MAC address : Displays the Ethernet MAC address. This is used for creating a DDNS address. - IP address : Displays the current IP address. - Subnet mask : Displays the for the set IP. - Gateway : Displays the for the set IP. - DNS server : Displays the DNS(Domain Name Service) server address. - HTTP webserver port : HTTP port used to access the camera via the web browser. The default is 80(TCP).
To set the user account 2. Add users or edit user ID or password. y User login ID/password list : Displays a list of accessible users ID, passwords, and ratings. - You can add up to 10 users. - The admin ID is "admin". - The password for the admin ID can be changed, but not added or deleted. User Registration 1. From the User setup window, click [Insert]. The Register User window appears. 2. Provide the , , and , respectively.
setup screen To edit a registered user account 1. From the User setup window, select a user ID to change. 2. From the User setup window, click [Modify]. The Modify user window appears. 3. Change the , , , and as you wish. 4. Click [Apply]. The selected user ID will be changed. To delete a user ID 1. From the User setup window, select a user ID to delete. 2. From the User setup window, click [Delete]. The selected user ID will be deleted.
SYSTEM SETUP To set the date/time You can obtain the current system time from the NTP server or your PC for your time setting. 2. If you select Manual, input the date and time manually. Your settings will be saved. y Current system time : The specified time in System Time Setup will be applied. y System time setup : You can synchronize the system time with the NTP server (time server) or your PC, or specify it manually. M You can specify the time between January 1, 2000 and December 31, 2037.
setup screen To check the log information Select - . The Log information list appears. y System log list : Shows the log information about the system changes along with time and IP address. - System started: When the camera turns on - User login: When the user logs in to the camera - System reset: When the camera restarts - Network is up: When accessing the network - Network is down: When not accessing the network - Video param.
4. When the software update is completed, you will be prompted to restart the system. 5. Click [OK] to restart the system. Since the current connection is disconnected, you have to connect to the system again. J If the network is disconnected, the power supply fails, or the PC abnormally operates during the update, the system does not work at all. Restart or reset the system if it does not work properly or causes a problem. Select - . The Reset window appears.
setup screen M To access the camera using HTTPS mode, you have to type the IP address for the camera in the form of “https://”. 2. When done, click [Apply]. The web viewer will switch to the set secure connection system. To Set IP Filtering 1. Click - . The IP Filtering Setup screen appears. y Basic policy : You can select the IP filtering policy. If you set to Permission, the web server allows all attempting IP addresses except the addresses added in the refusal list.
y Show time : Set to display the time information on the bottom screen. - Output Format : Select a display format of the time information. 24hr : Displays the time in the 24-hour format. 12hr : Displays the time in the 12-hour format. y Text color : Select black or white for the text color. y Background color : Select black or white for the background color.
setup screen - Use passive mode : Select this option when the passive mode connection is inevitable due to the firewall or FTP server setting. - FTP server address : Enter the IP address of a FTP server to which an alarm image will be transferred. - Upload path : You can specify the path of the FTP directory to which you will transfer an alarm image. You can specify the path by just typing or in this field.
To setup the record 1. Click - . The Record setup window appears. To set an alarm image You can configure to send message via FTP/E-mail (SMTP) or to save recording into the SD memory card. Select a transfer method when an event occurs or the schedule transfer function is activated. 1. Select - . The Alarm Image setup window appears. y Transfer mode : You can select alarm message notification method among FTP/E-mail transfer and SD Card recording.
setup screen - Post-alarm duration : The post alarm duration can be one among 5 seconds, 10 seconds, 15 seconds, and 30 seconds. You can send a post-alarm image of up to 30 seconds after the alarm is triggered. (The max time differs, depending on the frame rate) M The pre/post alarm duration is not available in SMTP transfer mode. Only one image at the corresponding time will be transferred. 2. When done, click [Apply]. Your settings will be saved. To set the alarm input 1.
To set the Motion Detection 1. Select a motion detection mode. 2. Specify the use of motion detection. 3. Select a sensitivity level of the motion detection. ● SETUP SCREEN 4. Place the cursor at a point in the video and drag it to whatever you need. You can specify up to 4 motion detection areas. 5. Specify the activation time and activation condition. For more information about and , refer to “Alarm input”. (page 62) 6. When done, click [Apply].
setup screen To set the Intelligent Video Analysis 1. Select an Intelligent Video Analysis mode. 2. Set whether to use the Intelligent Video Analysis function. 3. Set whether you want to use the overlay or not. 4. Select a sensitivity level of the camera’s object detection. 5. Specify the event rules. 6. Specify the activation time and activation condition. For more information about and , refer to “Alarm input”. (page 62) 7. When done, click [Apply].
y Overlay : If is selected, configured event rules and motion frame are displayed on the Live screen. Selecting will not display overlay information. M Motion frame is displayed in two types on the Live screen. Green frame – indicates the moving object Red frame – Temporarily displays the moving object detected by the configured event rules. y Set rules You can set the event rules. - Virtual line based rules : You can configure event rules for up to 3 virtual lines.
setup screen c Appearing: An object that has not been existed until the previous frame appears in the area. d Disappearing: An object that has been existed until the previous frame disappears from the area. e Scene Change: This event is generated by a complete scene change, such as camera veiled by hand or changed camera’s aiming, etc. - Object size: The maximum object size of motion detection for each event generation. The minimum size can be adjusted in 5 levels.
To set the scheduled transfer You can set to transfer the JPEG image to the FTP/SMTP server saved in the SD memory card at a specific interval. 2. When done, click [Apply]. Your settings will be saved. English _67 ● SETUP SCREEN 1. Select - . The Schedule Transfer setup window appears. y Schedule transfer function : If selecting , the schedule transfer function will be activated; if selecting , it will be deactivated.
setup screen NETWORK SETUP To set the video transfer mode You can control the transfer rate according to the video transfer mode and network speed. 1. Select - . The Video Transfer setup window appears. 2. When done, click [Apply]. Your settings will be saved. y VNP streaming : You can set the Samsung Protocol (VNP) for the streaming service. - Protocol : Select a video transfer protocol from TCP*, UDP (Unicast)*, and UDP (Multicast)*.
appendix PROFILE CAMERA SETUP MENU Parent Menu STANDARD ITS BACKLIGHT DAY/NIGHT ALC ALC ALC - - - DC DC DC GAMING BANK ALC ALC ALC - - - DC DC DC Sub-menus IRIS LENS LEVEL BACKLIGHT MOTION 0 0 0 0 0 0 OFF OFF WDR OFF OFF WDR (F.FAST) --- (F.FAST) --- NORM (F.FAST) --- SLOW (F.
appendix TERMINOLOGY y GOP : You can set between 5 and 15 for the MPEG4 and H.264 CODEC. The default is 15, and if set to 15, one I-Frame will be output per 15 frames as one I-Frame and 14 P-Frames constitute the GOP. The lower the GOP size is, the better the quality is; however, the bit rate as well as the data size will increase, causing a lower of the fps. GOP(Group of Pictures) is a set of video frames for MPEG4 and H.
English _71 ● APPENDIX y Filtering range The filtering range is calculated based on IP address and subnet mask provided by user as follows: The subnet value defines the number of masked bits, which will mask the IP address that is converted into 32-bit binary; rest of masked out bits are ignored to produce the range as shown below. Ex) IP address : 128.128.128.128 c If the Subnet is set to 8, converted IP is 1000 0000.1000 0000.1000 0000.
appendix SPECIFICATIONS Description Item Camera Type NTSC Color/BW Color Device Image Scanning Pixels Total Effective System Horizontal Frequency Vertical Frequency 1/3" Super-HAD PS CCD 811 x 508 768 x 494 Progressive 15.734 Hz 59.94 Hz 795 x 596 752 x 582 15.625 Hz 50 Hz Color Sens off : 0.12 Lux(15 IRE), 0.2 Lux(30 IRE), 0.4Lux(50 IRE)@F1.2 Sens up x512 : 0.00023 Lux(15 IRE), 0.0005 Lux(30 IRE), 0.0008Lux(50 IRE)@F1.2 B/W Sens off : 0.012 Lux(15 IRE), 0.02 Lux(30 IRE), 0.04Lux(50 IRE)@F1.
Description Item NTSC Horizontal 600 TV Lines PAL Resolution 350 TV Lines Video Output VBS 1.0Vp-p S/N Ratio S/N Ratio about 52 dB Lens Drive Type MANUAL/AI(VIDEO/DC) Mount Type CS/C ● APPENDIX Vertical Video Output Lens OS Network Board Hardware Embedded Linux Flash memory 32M byte RAM 256M byte DSP TI Davinci Ethernet RJ-45 (10/100BASE-T) PoE Yes (IEEE802.3af) Input 2 ea Output 2 ea Compression H.264 / MPEG4 / MJPEG Multiple Codec (H.
appendix Description Item NTSC IP Network Protocol Protocol IPv4 TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP, HTTPS, SSL, DHCP PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS IPv6 TCP/IP, HTTP, HTTPS, SSL, DHCP Streaming Unicast (TCP, UDP), Multicast (UDP) Security HTTPS Login Authentication Digest Login Authentication DDNS Supporting Samsung DDNS and Public DDNS services ONVIF Conformance Maximum User Access Connection PAL IPv4 / IPv6 Administrator User Access L
Item HTTP API CGI Command SDK RTP/RTSP API Power RTP Header, RTSP Command Document SDK ActiveX API for viewing data streams from IP camera. AC24V±10%(60Hz±0.3Hz)/ DC12V+10%/-5% / PoE (Power over Ethernet) Power Consumption Max. 6W(DC12V), Max. 7W(AC24V), Max. 8W(PoE) Operating Temp.
appendix FRAME RATE (NTSC) Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1) M H.
❖ H.
appendix ❖ MPEG4 (VGA) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 4055 Kbps 22 FPS 2580 Kbps 14 FPS 1290 Kbps 7 FPS 737 Kbps 4 FPS 221 Kbps 1 FPS LEVEL9 3533 Kbps 23 FPS 2304 Kbps 15 FPS 1075 Kbps 7 FPS 614 Kbps 4 FPS 184 Kbps 1 FPS LEVEL8 2949 Kbps 24 FPS 1843 Kbps 15 FPS 860 Kbps 7 FPS 492 Kbps 4 FPS 147 Kbps 1 FPS LEVEL7 2304 Kbps 25 FPS 1382 Kbps 15 FPS 645 Kbps 7 FPS 369 Kbps 4 FPS 111 Kbps 1 FPS LEVEL6 1536 Kbps 25 FPS 922 Kbps 15 FPS 430 Kbps 7 FPS 246 Kbps 4
❖ H.
appendix ❖ MPEG4 (CIF) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 1382 Kbps 30 FPS 691 Kbps 15 FPS 369 Kbps 8 FPS 184 Kbps 4 FPS 55 Kbps 1 FPS LEVEL9 1152 Kbps 30 FPS 576 Kbps 15 FPS 307 Kbps 8 FPS 154 Kbps 4 FPS 46 Kbps 1 FPS LEVEL8 922 Kbps 30 FPS 461 Kbps 15 FPS 246 Kbps 8 FPS 123 Kbps 4 FPS 37 Kbps 1 FPS LEVEL7 691 Kbps 30 FPS 346 Kbps 15 FPS 184 Kbps 8 FPS 92 Kbps 4 FPS 28 Kbps 1 FPS LEVEL6 461 Kbps 30 FPS 230 Kbps 15 FPS 123 Kbps 8 FPS 61 Kbps 4 FPS 18 Kbps 1
❖ H.
appendix FRAME RATE (PAL) Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1) M H.
❖ H.
appendix ❖ MPEG4 (VGA) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 4424 Kbps 20 FPS 2654 Kbps 12 FPS 1327 Kbps 6 FPS 664 Kbps 3 FPS 221 Kbps 1 FPS LEVEL9 3871 Kbps 21 FPS 2212 Kbps 12 FPS 1106 Kbps 6 FPS 553 Kbps 3 FPS 184 Kbps 1 FPS LEVEL8 3097 Kbps 21 FPS 1769 Kbps 12 FPS 885 Kbps 6 FPS 442 Kbps 3 FPS 147 Kbps 1 FPS LEVEL7 2433 Kbps 22 FPS 1327 Kbps 12 FPS 664 Kbps 6 FPS 332 Kbps 3 FPS 111 Kbps 1 FPS LEVEL6 1769 Kbps 24 FPS 885 Kbps 12 FPS 442 Kbps 6 FPS 221 Kbps 3
❖ H.
appendix ❖ MPEG4 (CIF) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 1382 Kbps 25 FPS 664 Kbps 12 FPS 332 Kbps 6 FPS 166 Kbps 3 FPS 55 Kbps 1 FPS LEVEL9 1152 Kbps 25 FPS 553 Kbps 12 FPS 276 Kbps 6 FPS 138 Kbps 3 FPS 46 Kbps 1 FPS LEVEL8 922 Kbps 25 FPS 442 Kbps 12 FPS 221 Kbps 6 FPS 111 Kbps 3 FPS 37 Kbps 1 FPS LEVEL7 691 Kbps 25 FPS 332 Kbps 12 FPS 166 Kbps 6 FPS 83 Kbps 3 FPS 28 Kbps 1 FPS LEVEL6 461 Kbps 25 FPS 221 Kbps 12 FPS 111 Kbps 6 FPS 55 Kbps 3 FPS 18 Kbps 1
❖ H.
appendix TROUBLESHOOTING PROBLEM SOLUTION y Check to make sure that the camera’s Network settings are appropriate. y Check to make sure that all network cables have been connected properly. I can’t access the camera from a web browser. y If connected using DHCP, verify that the camera is able to acquire dynamic IP addresses without any problem. y If connected using a DDNS URL, verify that the MAC address has been properly entered.
PROBLEM No JPEG file is transferred via FTP/ SMTP on occurrence of intelligent video analysis event of camera even when the is set to . SOLUTION y Verify the settings in the following sequence: A. NTP must be properly configured. B. The should be set to . C. Alarm Video Transmission must be enabled. D. Check for scheduling conflict. y Yes, it can be. You can set rules for events despite of the intelligent video analysis setting.
GPL/LGPL SOFTWARE LICENSE The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.
based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.
a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10.
WARRANTY ; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program ; if not, write to the Free Software Foundation, Inc.,51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail.
or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License.
3. Protecting Users' Legal Rights From Anti-Circumvention Law. No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11). from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement).
work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such. 14. Revised Versions of this License. The Free Software Foundation may publish revised and/ or new versions of the GNU General Public License from time to time.
USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it.
Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing nonfree programs.
is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1.
it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4.
1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine readable “ work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.
it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10.
later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission.
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail.
Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@ cryptsoft. com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft. com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com www.samsungipolis.com SAMSUNG TECHWIN EUROPE LTD.
