User manual

ManualsBrandsSamsung ManualsDigital CameraSMARTCAM

With SmartCam app, you can monitor what matters to you

directly from your smart phone.

Download the application from the Play Store and install it on

your smart phone.



Search keywords for the application: “Samsung SmartCam”,

“Smartcam”, “Samsung techwin”, “Techwin”.

Hardware / Operating System Requirements

OS - Android 2.3.3/4.0/4.1/4.2/4.3

CPU - 1GHz or higher

RAM

- 128MB or more (recommended),

RAM : 50MB (Minimum)

Network

Wi-Fi or 3G/LTE wireless communication-

enabled smart phone

Video Codec - H.264

Recommended Smart Phones - Galaxy S3/S4

Recommended Tablet PC - Galaxy Note 10.1

 If you use 3G or 4G(LTE) data communication, excessive amount of

fees can be billed and may cause data delays or loss. Wi-Fi is

recommended.

1. Run the downloaded application.

2. Tap <Create new account>.

1. Smart phone requirements

2. Subscription

SmartCam

Android

English

3. Tap <Start>.

4. Enter requested information.

 Email address is used to find the

account password.

Check “Agree to the terms and

conditions”, and tap <Register>.

6. Tap <Next> when the menu on

the completion of a new member

registration pops up.

 Tap <Add Camera> after logging

in if you are already a member.

|Enter User ID.

Enter Password.

Remember me Auto Login

Forgot your ID?

Forgot your password?

Create new account

Name

e-Mail

I agree to the Samsung Techwin's terms and

conditions.

Terms of Services

8~14 alpha numeric characters

Confirm Password

Enter the user name.

ex) xxxx@samsung.com

) xxxx@samsung.com

)

xxxx

samsung.com

Account created. Tap <Next> to

setup the camera.

Cancel Next

Camera Setup About

Add Camera

Welcome to

Start

Setup using 3 simple steps below.

Step 1. Sign up for an account

Step 2. Register your camera

Step 3. Configure your camera

Summary of content (8 pages)

PAGE 1
. Smart phone requirements Hardware / Operating System SmartCam Android English 3. Tap . Requirements OS - Android 2.3.3/4.0/4.1/4.2/4.3 CPU - 1GHz or higher RAM - 128MB or more (recommended), RAM : 50MB (Minimum) Network Video Codec Recommended Smart Phones Welcome to - Wi-Fi or 3G/LTE wireless communicationenabled smart phone Setup using 3 simple steps below. Step 1. Sign up for an account Step 2. Register your camera - H.264 Step 3.
PAGE 2
9. After selecting a camera to connect, tap . Wi-Fi Direct connection M   You can only use it in a camera that has a Wi-Fi Direct sticker attached to it. M  Registration Select a camera that has the last four digits of the serial number displayed on the back of the product. Select a camera that has the last four digits of the serial number on the back of the product.
PAGE 3
. Camera List 10. If the camera is not detected, please enter the camera serial number manually. Cable connection 7. Tap . M  For camera’s serial number location, refer to [ ]. No matching camera is found. Check the serial number and enter it down below. 1. Move to the item. From the listed active cameras, ] on tap the desired camera’s [ the right. Serial number Camera Prev M Next  1 2 3 4 5 6 7 8 9 0 q w e If yes, select Wireless Setup. If not, select Wired Setup.
PAGE 4
. Live Video 1. Tap the desired camera’s [ tap the icon. Live Video ] or Camera Setup No. Add Camera M  If there is the latest version of firmware, when you make a live video connection, a pop up will appear so that you can update your camera’s firmware. Description About test A user can record audio and play the recorded audio through the camera speaker. test Audio playing test test2 test IR Lighting Live 2. Enter the for the camera selected.
PAGE 5
Motion zone Cancel Reset OK Relay mode General setting If the router where your camera is connected to does not have the UPnP function or if the camera is connected to a dual router, your mobile device will be connected to the 3G or LTE network in a relay mode and you will see the video for the first seven ] in your live minutes only. In relay mode, you can check [ video. When setting your device to a Wi-Fi network,you can make a connection in general mode. 1. Tap . J  1.
PAGE 6
• status LED : You can turn on or off the LED on your camera.  SNH-P6410BN supported 1. Tap the . • Firmware Version : You can check the current version and the latest distributed version and even make updates. If there is the latest version of firmware, when you make a live video connection, a pop up will appear so that you can update your camera’s firmware. 3. Tap . J  Network setting Network 2. Set your event items.
PAGE 7
6. Event List 1. Tap on the icon to see the YouTube and Picasa event links. M  2. Detected events will be saved in the server and displayed in the event list. test YouTube icon: Tap on the YouTube icon to play the YouTube video. Only when you set YouTube/Picassa after registering a Google account, it will be displayed in the event list. Deleting Each Event 1. Tap and hold the desired event to be deleted.
PAGE 8
7. SD playing 9. Alarm setting SD Save J     Continuous recording automatically saves video to SD memory every five minutes. Manual recording is started by pressing the manual recording button in the live video. If you close the app without releasing the button, an additional 30 seconds of video will be saved before termination. Event recording saves motion or audio for thirty seconds and if motion or audio is detected again in the meantime, the amount of saving time is extended.