GSM TELEPHONE SGH-E210 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams 8. PCB Diagrams 9. Flow Chart of Troubleshooting 10.
GSPN (Global Service Partner Network) Country Web Site North America service.samsungportal.com Latin America latin.samsungportal.com CIS cis.samsungportal.com Europe europe.samsungportal.com China china.samsungportal.com Asia asia.samsungportal.com Mideast & Africa mea.samsungportal.com This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. ⓒ Samsung Electronics Co.,Ltd. 2007. 08. Rev.1.
1. Safety Precautions 1-1. Repair Precaution ● Repair in Shield Box, during detailed tuning. Take specially care of tuning or test, because specipicty of cellular phone is sensitive for surrounding interference(RF noise). ● Be careful to use a kind of magnetic object or tool, because performance of parts is damaged by the influence of manetic force. ● Surely use a standard screwdriver when you disassemble this product, otherwise screw will be worn away. ● Use a thicken twisted wire when you measure level.
Safety Precautions 1-2. ESD(Electrostatically Sensitive Devices) Precaution Several semiconductor may be damaged easilly by static electricity. Such parts are called by ESD(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below. You can prevent from ESD damage by static electricity. ● Remove static electricity remained your body before you touch semiconductor or parts with semiconductor.
2. Specification 2-1. GSM General Specification GSM 90 0 DCS1800 PCS1900 F req . Ba nd[MHz] Uplink/Downlin k 880~91 5 925~96 0 1 710~17 85 1 805~18 80 1850~1 910 1930~1 990 ARF CN r ange 0~124 & 975~1 023 512~88 5 512~8 10 T x/Rx spacing 45MHz 95MHz 80MHz Mod. Bit r ate / Bit Period 270 .833Kbps 3.692 us 270 .833Kbps 3.692 us 27 0.833 Kbps 3.69 2us Ti me Slo t Pe rio d /Frame Period 576.9 us 4. 615ms 576.9 us 4. 615ms 576. 9us 4 .615ms Modulatio n 0.3G M SK 0.3G MSK 0.
Speclflcation 2-2.
3.
4.
Array course control Software Downloading 4-1. Downloading Binary Files • Three binary files for downloading SGH-E210. – E210XXYY.s3 : Main source code binary. 4-2. Pre-requsite for Downloading • Downloader Program(OptiFlash.
Array course control 4-3. S/W Downloader Program 1. Load the binary download program by executing the “OptiFlash.exe” 2. Select the “Options” -> “Settings” -> “Generic” -> “Specify hardware platform”. Choose hardware platform for the downloader file setting.
Array course control 3. Select the COM port when the download cable is connected Up to 64 ports are supported. Additionally you can select the maximum transfer speed OptiFlash will use to communicate with the phone.
Array course control 4. Select the“Flash&Verify” -> “Browse” Set the directory path and choose the latest s/w binary, for example “E210XXYY.s3”, for the downloader binary setting. Make sure that not to change the reserved memory regions.
Array course control 5. Click “OK” button then press “Flash”. (Before pressing ‘Flash’ button, push the button ‘*’and ‘END’ at the same time. Then press ‘Flash’.) Downloader will upload the binary file as below for the downloading. 6. When downloading is finished successfully, there is a “All is well” message. 7. After finishing downloading, Certain memory resets should be done to guarantee the normal performance. 8. Confirm the downloaded version name and etc.
5. Exploded View and Parts List 5-1.
Main Electrical Parts List 5-2.
Main Electrical Parts List Discription SEC CODE BAG PE 6902-000297 ADAPTOR-ATADS10EBE,BLK,EU GH44-01702A EARPHONE-SGHE210,HEADSET,BLK,A GH59-04535A LABEL(P)-UNIT SEAL GH68-00518B LABEL(R)-WATER SOAK GH68-09361A MANUAL USERS-EU ENGLISH GH68-13874A MANUAL USERS-EU PORTUGUESE GH68-13884A LABEL(R)-MAIN(EU) GH68-13957A BOX(P)-UNIT MAIN(EU) GH69-05052A CUSHION-CASE TA2 MA2 GH69-05053A MPR-REMOVE TAPE LCD GH74-13804A TAPE GASK GH74-31842A TAPE INSU GH74-32033A TAPE GH74-33512A TAPE-L
6.
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 2404-001414 TA403 C-TA,CHIP SA 2404-001414 TA404 C-TA,CHIP SA 2404-001406 TA400 C-TA,CHIP SA 2404-001381 TA405 C-TA,CHIP SA 2404-001381 TA406 C-TA,CHIP SA 2203-006979 C235 C-CER,CHIP SA 2203-006838 C126 C-CER,CHIP SA 2203-006838 C127 C-CER,CHIP SA 2203-006838 C215 C-CER,CHIP SA 2203-006838 C314 C-CER,CHIP SA 2203-006838 C349 C-CER,CHIP SA 2203-006838 C350 C-CER,CHIP SA 2203-006838 C351
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 2203-006562 C370 C-CER,CHIP SA 2203-006562 C372 C-CER,CHIP SA 2203-006562 C404 C-CER,CHIP SA 2203-006562 C405 C-CER,CHIP SA 2203-006562 C406 C-CER,CHIP SA 2203-006562 C450 C-CER,CHIP SA 2203-006562 C460 C-CER,CHIP SA 2203-006562 C473 C-CER,CHIP SA 2203-006556 C104 C-CER,CHIP SA 2203-006556 C200 C-CER,CHIP SA 2203-006474 C316 C-CER,CHIP SA 2203-006423 C113 C-CER,CHIP SA 2203-006423 C117
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 2203-006318 C110 C-CER,CHIP SA 2203-006318 C112 C-CER,CHIP SA 2203-006260 C130 C-CER,CHIP SA 2203-006257 C318 C-CER,CHIP SA 2203-006194 C114 C-CER,CHIP SA 2203-006194 C115 C-CER,CHIP SA 2203-006194 C209 C-CER,CHIP SA 2203-006194 C234 C-CER,CHIP SA 2203-006194 C319 C-CER,CHIP SA 2203-006194 C320 C-CER,CHIP SA 2203-006194 C321 C-CER,CHIP SA 2203-006194 C374 C-CER,CHIP SA 2203-006183 C220
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 2203-005682 C410 C-CER,CHIP SA 2203-005682 C411 C-CER,CHIP SA 2203-005682 C412 C-CER,CHIP SA 2203-005682 C413 C-CER,CHIP SA 2203-005682 C414 C-CER,CHIP SA 2203-005682 C415 C-CER,CHIP SA 2203-005682 C416 C-CER,CHIP SA 2203-005682 C417 C-CER,CHIP SA 2203-005682 C418 C-CER,CHIP SA 2203-005682 C419 C-CER,CHIP SA 2203-005682 C420 C-CER,CHIP SA 2203-005682 C421 C-CER,CHIP SA 2203-005682 C422
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 2203-005482 C228 C-CER,CHIP SA 2203-005482 C371 C-CER,CHIP SA 2203-005482 C476 C-CER,CHIP SA 2203-005050 C140 C-CER,CHIP SA 2203-002709 C214 C-CER,CHIP SA 2203-002709 C221 C-CER,CHIP SA 2203-002709 C232 C-CER,CHIP SA 2203-002709 C315 C-CER,CHIP SA 2203-002709 C472 C-CER,CHIP SA 2203-001072 C310 C-CER,CHIP SA 2203-001072 C311 C-CER,CHIP SA 2203-000940 C227 C-CER,CHIP SA 2203-000812 C226
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 2007-008774 R259 R-CHIP SA 2007-008579 R257 R-CHIP SA 2007-008531 R266 R-CHIP SA 2007-008531 R319 R-CHIP SA 2007-008516 R243 R-CHIP SA 2007-008483 R102 R-CHIP SA 2007-008483 R105 R-CHIP SA 2007-008483 R412 R-CHIP SA 2007-008478 R248 R-CHIP SA 2007-008420 R250 R-CHIP SA 2007-008420 R252 R-CHIP SA 2007-008419 R414 R-CHIP SA 2007-008419 R416 R-CHIP SA 2007-008419 R417 R-CHIP SA 2007-
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 2007-000242 R422 R-CHIP SA 2007-000173 R406 R-CHIP SA 2007-000173 R408 R-CHIP SA 2007-000170 R261 R-CHIP SA 2007-000170 R402 R-CHIP SA 2007-000170 R403 R-CHIP SA 2007-000168 R246 R-CHIP SA 2007-000162 R256 R-CHIP SA 2007-000157 R247 R-CHIP SA 2007-000153 R413 R-CHIP SA 2007-000153 R421 R-CHIP SA 2007-000148 R267 R-CHIP SA 2007-000138 R411 R-CHIP SA 2007-000138 R420 R-CHIP SA 1405-
Exploded View and Parts List SEC CODE Design LOC Discription STATUS 0406-001254 ZD405 DIODE-TVS SA 0406-001241 U401 DIODE-TVS SA 0406-001241 U402 DIODE-TVS SA 0406-001241 U403 DIODE-TVS SA 0406-001241 U404 DIODE-TVS SA 0406-001241 U405 DIODE-TVS SA 0406-001241 U406 DIODE-TVS SA 0406-001237 U201 DIODE-TVS SNA 0403-001547 ZD402 DIODE-ZENER SA 0403-001547 ZD403 DIODE-ZENER SA 0403-001427 ZD406 DIODE-ZENER SA 6-9 SAMSUNG Proprietary-Contents may change without n
7. Disassembly and Assembly Instructions 7-1. Disassembly 2 1 1) Unscrew 4 screws. ※ caution ※ caution 1) Remove battery and SIM card. 1) Be careful not to scratch molding. 4 3 1) Separate LCD CONNECTOR from the PBA 1)Lift up the REAR CASE and separate it from the using tweezers. FRONT. ※ caution ※ caution 1) Be careful not to damage the components around LCD CONNECTOR. 1) Be careful not to damage LOCKER.
Exploded View and Parts List 6 5 1) Slowly separate the PBA from the keypad using tweezers. ※ caution 1) Be careful not to damage double-faced tape on the keypad. 1) Lift up the PBA by pushing the keypad. 2) Be careful not to damage the DOPARO SHEET ※ caution 1) Be careful not to damage the FRONT molding. (light guide film) . 8 7 1) Remove the keypad from the ass'y. ※ caution 1) Remove the black tape with tweezers.
Exploded View and Parts List 10 9 1) Push the Hinge with tweezers(Top view) and separate the FOLDER Ass'y from the FRONT. ※ caution 1) Separate the FOLDER Ass'y from the FRONT. 1) Be careful not to damage the FRONT molding and the Hinge. ※ caution 11 12 1) Remove the two screw sheets. 1) Unscrew at two points. ※ caution 1) Be careful not to damage the LCD FPCB. ※ caution 1) Be careful not to scratch molding. 1) Be careful not to scratch molding.
Exploded View and Parts List 14 13 1) Open the locker between the FOLDED UPPER and the FOLDER LOWER. 1) Separate the UPPER and the LOWER. ※ caution ※ caution 1) Be careful not to scratch molding. 1) Be careful not to damage LOCKER and molding 15 16 1) Using tweezers, separate the SPEAKER from the FOLDER LOWER. 2) Do for the MOTOR in the same way. ※ caution 1) Be careful not to damage thePEAKER/MOTOR and wires. 1) Open the camera connector with tweezers.
Exploded View and Parts List 18 17 1) Bend the LOWER slightly and separate the LCD and the LOWER. 1) Separate the LCD FPCB from the LOWER. ※ caution ※ caution 1) Do not touch LCD GLASS with your hands. 1) Be careful not to damage the LCD FPCB. 19 1) Completed. ※ caution 1) Be careful not to leave any foreign substance or fingerprint on the SUB-LCD.
Exploded View and Parts List 7-2. Assembly 1 1) ※ 1) or 2 LCD Ass'y caution Be careful not to leave any foreign substance fingerprint on the SUB-LCD. 1) Insert the LCD FPCB into the hole on the LOWER carefully ※ caution 1)Be careful not to damage the FPCB. 4 3 1) Put the LCD Ass'y into place as shown. 1) Put the camera into place. 2) Put the speaker and motor into place. 2) As shown,put the connector until it clicks ※ caution ※ caution 1) Adjust a tape before putting the LCD.
Exploded View and Parts List 6 5 1) Assembling the FOLDER should be done in regular sequence as shown.(TOP-> BOTH SIDES OF THE LCD ->BOTH SIDES OF THE SUB-LCD→ BOTTOM) 1) Tighten 2 screws. ※ caution ※ caution 1) Check if there are not any foreign substance. 2) Be careful not to make scratch and damage. 1) Be careful not to make scratch and damage. 7 8 1) Put up screw sheets. ※ caution 1) Be careful not to make scratch and damage. 1) Insert the FPCB of the FOLDER ASS'Y assembled.
Exploded View and Parts List 10 9 1) Con To Con 에 0.3T 도전Tape를 부착한다. 1) Set the FRONT ASS'Y into the hole after pressing the HINGE. ※ caution 1) Be careful not to make scratch and damage. 1) Put up the tape. ※ caution 11 12 1)As shown in the above picture, insert the upper keypad first,and reverse the phone. Fit the lower keypad in carefully by folding and unfolding it. ※ caution 1) Be careful not to fold the keypad. 1) The tape should not be on the FPCB.
Exploded View and Parts List 14 13 1) Press the PBA while pulling the cover of Micro SD. ※ caution 1)Make sure of adjustng the Micro SD before 1) Fit the LCD connector into the PBA. ※ caution 1) Press the connector until it clicks. 2) When pressing the connector, be careful not to pressing the PBA. break the neighbor components. 15 16 1) Insert the top of the REAR carefully first, and press the bottom. ※ caution 1) Be careful not to make scratch and damage. 1) Tighten 4 screws.
8.
9.
PCB Diagrams LED400 PWR CLEAR SEND RIGHT I DOWN LEFT STO MENU UP U202 1 2 4 5 8 9 0 SHARP TP214 TP215 TP212 TP211 TP213 TP210 TP209 TP217 JCON200 9-2 VR401 STAR LED402 6 LED401 7 3
10. Flow Chart of Troubleshooting 10-1.Baseband 10-1-1. Power ON 'Power ON' Does not work Check the current consumption Check comsumption ≥ 100mA NO Down load again YES VBat ≥ 3.3V ? NO Charge the Battery YES C348 ≥ 1.8V ? NO Check UCD300 and C348 YES C347 ≥ 2.9V? NO YES C318≥2.9V? NO Check UCD301 and C318 YES Check the clock signal NO at pin #3 of OSC100 Check the clock OSC100 Freq.=26MHz,Vrms ≥500mV YES NO Check pin #8 of UCD101 Freq.
Flow Chart of Troubleshooting 10-1-2. Initial Initial Failure NO The voltage at the C348=1.8V? The voltage at the C347=2.9V? Check the UCD300 (If it has some problem, it has to be replaced.) YES The voltage at pin#4 NO of U300 " Low --> High" ? Check the UCD300 (If it has some problem, it has to be replaced.) YES NO There is 32.768KHz wave form at the C329, C330 ? Check the UCD300 YES The voltage is 2.
Flow Chart of Troubleshooting 10-1-3. Sim Part "Insert SIM" is displayed on the LCD Sim socket checking NO "Is it inserted?" Insert Simcard YES NO The voltage is 2.
Flow Chart of Troubleshooting 10-1-4. LCD Display part LCD display is abnormal Check LCD connection and replace LCD LCD Backlight is on? NO pin#1 of FPCB02 YES Check LCD Check FPCB02 is high? NO YES pin#2 of U401 YES is high? NO C12 > 3.5V? NO Check C12 Recharge Bat. YES pin#6 of U01 NO is high? YES CHeck U01 C444 is 2.
Flow Chart of Troubleshooting 10-1-5. Microphone Part Micro-phone does not work NO Soldering OK? Solder the microphone again YES Check the DC bias voltage on Mic path. NO The voltage of C456 is about 2.
Flow Chart of Troubleshooting 10-1-6. Speaker Part There is no sound from speaker.
Flow Chart of Troubleshooting 10-1-7. Camera part Camera function does not work NO Is the connect CN02 ok? Connect the CN02 YES NO #40 of HEA400 IS HIGH? Check UCD301 YES Pin #1 of Q01 = 1.5V? NO YES Pin #7 of Q01 IS HIGH? Check Q01 NO YES Check Bat. Pin #6 of Q01 = 2.8V? NO YES Pin#3 of OSC300 is 27MHz? NO Pin #7 of Q01 = High? Q01 Check Bat.
Flow Chart of Troubleshooting 10-1-8.
Flow Chart of Troubleshooting 10-2. RF 10-2-1.
Flow Chart of Troubleshooting 10-2-2. GSM900 TX PAM100 Pin#12 About 2~3 dBm? NO C125 High, C120 = Low? YES NO UCD300,C120,C125 Check / Change YES RFS100, L101, C102, L102, C109, L104 Check / Change PAM100 Pin#1 4~5dBm ? NO YES PAM100 Check & Change C122 = 3.7V? NO Check the Battery Block YES PAM101 Pin #8 1.2V? NO R101, C123 Check & Resolder Check UCD300 TXP YES UCD101 Check Pin #13 >2.8V? NO C131, UCD300 Check or resolder YES UCD101 check Pin#31 :26Mhz? Vpp:1.
Flow Chart of Troubleshooting 10-2-3. DCS1800 & PCS1900 TX PAM100 Pin#12 About 2~3 dBm? NO NO PAM100 Pin#4, #5 High? YES UCD300,C120,C125 Check / Change YES RFS100, L101, C102, L102, C109, L104 Check / Change PAM100 Pin#1 4~5dBm ? NO YES PAM100 Check & Change C122 = 3.7V? NO Check the Battery Block YES PAM101 Pin #8 1.2V? NO R101, C123 Check & Resolder Check UCD300 TXP YES UCD101 Check Pin#13 ≥ 2.8V ? NO C131, UCD300 Check or resolder YES UCD101 Check Pin #31 : 26MHz ? Vpp : 1.
11. Reference data 11-1. Reference Abbreviate AAC: Advanced Audio Coding. AVC : Advanced Video Coding.
