© 2006 Samsung Electronics Co., Ltd. All rights reserved. This manual is provided for information purposes only. All information included herein is subject to change without notice. Samsung Electronics is not responsible for any direct or indirect damages, arising from or related to use of this manual. • SCX-5330N and SCX-5530FN are model names of Samsung Electronics Co., Ltd. • Samsung and Samsung logo are trademarks of Samsung Electronics Co., Ltd.
CONTACT SAMSUNG WORLDWIDE If you have any comments or questions regarding Samsung products, contact the Samsung customer care center. Country Customer Care Center Web Site Country Customer Care Center Web Site LITHUANIA 8-800-77777 www.samsung.com/lt ARGENTINE 0800-333-3733 www.samsung.com/ar LUXEMBURG 0035 (0)2 261 03 710 www.samsung.com/be AUSTRALIA 1300 362 603 www.samsung.com/au MALAYSIA 1800-88-9999 www.samsung.com/my AUSTRIA 0800-SAMSUNG (726-7864) www.samsung.
CONTENTS 1. Introduction Special features ...................................................................................................................................................... 1.1 Printer overview ...................................................................................................................................................... 1.2 Understanding the Status LED ..................................................................................................................
7. Basic printing Printing a document ................................................................................................................................................ 7.1 Canceling a print job ............................................................................................................................................... 7.1 8. Scanning Scanning basics ..............................................................................................................................
13. Maintenance Printing reports ...................................................................................................................................................... 13.1 Cleaning your machine ......................................................................................................................................... 13.2 Maintaining the toner cartridge ..............................................................................................................................
Important Precautions and Safety Information 17 The Power cord supplied with your machine should be used for safe operation. If you are using a cord which is longer than 2 m with 110 V machine, then it should be 16 AWG1 or bigger. When using this machine, these basic safety precautions should always be followed to reduce risk of fire, electric shock and injury to people: 1 Read and understand all instructions. 18 Use only No.26 AWG* or larger telephone line cord.
Mercury Safety television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or experienced radio TV technician for help.
EC Certification WARNING: FCC Regulations state that changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. In the event that terminal equipment causes harm to the telephone network, the telephone company should notify the customer that service may be stopped.
EU Declaration of Conformity (R&TTE) We, Samsung Electronics Co., Ltd. of of Samsung Electronics Co., Ltd. #259, Gongdan-Dong, Gumi-City, Kyungbuk, Korea 730-030 Shandong Samsung Telecommunications Co., Ltd.
1 Introduction Expand your machine’s capacity • The SCX-5330N has 64 MB of memory which can be expanded to 320 MB. The SCX-5530FN has 96 MB of memory which can be expanded to 320 MB. • You can add a 250-sheet optional tray 2 to your machine. This tray lets you add paper to the machine less often. • Zoran IPS Emulation* compatible with PostScript 3 (PS) enables PS printing (SCX-5530FN only). Thank you for purchasing this Samsung multifunctional product.
Printer overview These are the main components of your machine: Front view Rear view * The figure above shows an SCX-5530FN with all available accessories. * The figure above shows an SCX-5530FN with all available accessories.
Control panel overview (SCX-5530FN) 1 Speed buttons: Allows you to store frequently-dialed fax numbers and email addresses and enter them with the touch of a few buttons. 13 Back: Sends you back to the upper menu level. 2 Shift: Allows you to shift the speed buttons to access numbers 16 through 30. 14 Status: Shows the status of your machine. See page 1.5. 3 Address Book: Allows you to store frequently used fax numbers in memory or search for stored fax numbers or email addresses.
Control panel overview (SCX-5330N) 1 Copy: Activates Copy mode. 9 Darkness: Adjusts the document brightness for the current copy job. 2 Scan/Email: Activates Scan mode. 10 Original Type: Selects the document type for the current copy job. 3 Display: Shows the current status and prompts during an operation. 11 Reduce/Enlarge: Makes a copy smaller or larger than the original. 4 Menu: Enters Menu mode and scrolls through the available menus.
Understanding the Status LED Finding more information The Status LED on the control panel shows the status of your machine. See the table below to know your machine’s status. You can find information for setting up and using your machine from the following resources, either printed or onscreen. Status Off Green Red Description • The machine is off-line. • The machine is in Power Save mode. When data is received, or any button is pressed, it switches to on-line automatically.
Selecting a location Select a level, stable place with adequate space for air circulation. Allow extra space for opening covers and trays. The area should be well-ventilated and away from direct sunlight or sources of heat, cold, and humidity. Do not set the machine close to the edge of your desk or table.
2 System setup This chapter gives you an overview of menus available on your machine and step-by-step instructions for setting up the machine’s systems.
6 Changing the display language Press OK to save the time and date. When you enter a wrong number, Out of Range appears and the machine does not proceed to the next step. If this happens, simply reenter the correct number. To change the language that appears on the control panel, follow these steps: 7 Press Stop/Clear to return to Standby mode. 1 Press Menu until System Setup appears on the bottom line of the display and press OK. 2 Press OK when Machine Setup appears.
Setting sounds (SCX-5530FN only) Entering characters using the number keypad You can control the following sounds: As you perform various tasks, you may need to enter names and numbers. For example, when you set up your machine, you enter your name or your company’s name, and the fax number. When you store fax numbers or email addresses in memory, you may also enter the corresponding names. • Key Sound: Turns the key sound on or off. With this option set to On, a tone sounds each time a key is pressed.
Correcting numbers or names Scan Power Save mode If you make a mistake while entering a number or name, press the left Scroll button to delete the last digit or character. Then enter the correct number or character. Scan Power Save mode allows you to save power by turning off the scan lamp. The scan lamp under the scanner glass automatically turns off when it is not in actual use to reduce power consumption and extend the life of the lamp.
3 Software overview CD PostScript printer driver CD This chapter gives you an overview of the software that comes with your machine. Further details about installing and using the software are explained in the Software Section. Supplied software • Printer driver features • System requirements Supplied software You must install the printer and scanner software using the supplied CDs after you have set up your machine and connected it to your computer.
Printer driver features System requirements Your printer drivers support the following standard features: • Paper source selection Before you begin, ensure that your system meets the following requirements: • Paper size, orientation and media type Windows • Number of copies Item In addition, you can use various special printing features.
Linux Item Requirements Operating system • • • • Red Hat 8.0 ~ 9.0 Fedora Core 1 ~ 3 Mandrake 9.2 ~ 10.1 SuSE 8.2 ~ 9.2 CPU Pentium IV 1 GHz or higher RAM 256 MB or higher Free disk space 1 GB or higher Software • • • • Linux Kernel 2.4 or higher Glibc 2.2 or higher CUPS SANE(for MFP device only) Notes • It is necessary to claim swap partition of 300 MB or larger for working with large scanned images. • The Linux scanner driver supports the optical resolution at maximum.
4 Network setup Via the control panel You can set up the following basic network parameters through the machine’s control panel: This chapter gives you step-by-step instructions for setting up your machine for network connections.
Static addressing Configuring EtherTalk To enter a TCP/IP address from your machine’s control panel, take the following steps: 1 Press Menu until Network appears on the bottom line of the display and press OK. 2 Press OK when TCP/IP appears. 3 EtherTalk is AppleTalk used in an Ethernet network. This protocol is widely used in Macintosh network environments. To use EtherTalk, take the following steps: 1 Press Menu until Network appears on the bottom line of the display and press OK.
Setting Ethernet speed 5 Double click Setup.exe to install this program. 6 From the Windows Start menu, select Programs > Samsung Network Printer Utilities > SetIP. 7 Select the name of your printer and click “ You can select the communication speed for Ethernet connections. 1 Press Menu until Network appears on the bottom line of the display and press OK. 2 Press the Scroll buttons until Ethernet Speed appears and press OK.
5 Loading originals and print 2 Place the original face down on the scanner glass and align it with the registration guide at the top left corner of the glass. 3 Close the scanner lid. media This chapter introduces you to how to load originals and print media into your machine.
To load an original into the ADF: 1 Selecting print media Load the original face up into the ADF. Make sure that the bottom of the original stack matches the paper size marked on the document input tray. You can print on a variety of print media, such as plain paper, envelopes, labels, and transparencies. Always use print media that meet the guidelines for use with your machine.
Supported print media types and sizes Type Plain paper Size Dimensions Weight1 Capacity2 • 60 to 90 g/m2 (16 to 24 lb bond) for the tray • 60 to 163 g/m2 (16 to 43 lb bond) for the multi-purpose tray • 250 sheets of 75 g/m2 (20 lb bond) paper for the tray • 50 sheets for the multipurpose tray 75 to 90 g/m2 (20 lb to 24 lb bond) 5 sheets of 75 g/m2 (20 lb bond) in the multi-purpose tray Letter 216 x 279 mm (8.5 x 11 inches) Legal 216 x 356 mm (8.5 x 14 inches) Folio 216 x 330.2 mm (8.
Media sizes supported in each mode Mode Size Guidelines for special print media Media type Source Copy mode Letter, A4, Legal, Folio, Executive, ISO B5, JIS B5, A5, A6 • tray 1 • optional tray 2 • multi-purpose tray Single side printing All sizes supported by the machine • tray 1 • optional tray 2 • multi-purpose tray Duplex printing1 Letter, A4, Legal, Folio • tray 1 • optional tray 2 • multi-purpose tray Fax mode2 Letter, A4, Legal • tray 1 • optional tray 2 Envelopes 1.
Media type Guidelines Transparencies • To avoid damaging the machine, use only transparencies designed for use in laser printers. • Transparencies used in the machine must be able to withstand 180 °C, the machine’s fusing temperature. • Place them on a flat surface after removing them from the machine. • Do not leave them in the paper tray for long periods of time. Dust and dirt may accumulate on them, resulting in spotty printing. • To avoid smudging caused by fingerprints, handle them carefully.
Loading paper in the tray 1 or optional tray 2 1 1 Press and hold the guide lock, and slide the paper length guide to locate it in the correct paper size slot. 2 After inserting paper into the tray, adjust the support guide so that it lightly touches the paper stack. 3 Squeeze the paper width guides, as shown and slide them to the stack of paper until it lightly touches the side of the stack. Pull open the paper tray and load paper. You can load letterhead with the design side face down.
In the multi-purpose tray Notes The multi-purpose tray can hold special sizes and types of print material, such as transparencies, postcards, note cards, and envelopes. It is useful for single page printing on letterhead or colored paper. Depending on the media type you are using, keep the following loading guidelines: • Envelopes: Flap side down and with the stamp area on the top left side. • Transparencies: Print side up and the top with the adhesive strip entering the machine first.
Tips on using the multi-purpose tray Selecting an output location • Load only one size of print media at a time in the multi-purpose tray. The machine has two output locations: the rear cover (face up) and the output tray (face down). • To prevent paper jams, do not add paper when there is still paper in the multi-purpose tray. This also applies to other types of print media.
Printing to the rear cover Using the rear cover, paper comes out of the machine face up. Printing from the multi-purpose tray to the rear cover provides a straight paper path. Using the rear cover might improve the output quality with special print media. To use the rear cover, open it by pulling down. Caution The fuser area inside the rear cover of your machine becomes very hot when in use. Take care when you access this area. 5.
6 Copying Note You can cancel the copy job during an operation. Press Stop/ Clear, and the copying will stop. This chapter gives you step-by-step instructions for copying documents.
Reduced or enlarged copy Using special copy features By using the Reduce/Enlarge button, you can reduce or enlarge the size of a copied image from 25% to 400% when you copy original documents from the scanner glass, or from 25% to 100% from the ADF. You can use the following copy features: To select from the predefined copy sizes: Collation 1 Press Reduce/Enlarge. 2 Press Reduce/Enlarge or the Scroll buttons until the size setting you want appears and press OK.
ID card copying Poster copying Your machine can print 2-sided originals on one sheet of A4-, Letter-, Legal-, Folio-, Executive-, B5-, A5-, or A6-sized paper. Your machine can print an image onto 9 sheets of paper (3x3). You can paste the printed pages together to make one poster-sized document. When you copy using this feature, the machine prints one side of the original on the upper half of the paper and the other side on the lower half without reducing the size of the original.
Clone copying Copying on both sides of paper (SCX-5530FN only) Your machine can print multiple image copies from the original document on a single page. The number of images is automatically determined by the original image and paper size. By using the Duplex button on your machine, you can set the machine to print copies on both sides of paper. This copy feature is available only when you place originals on the scanner glass. 1 Press Copy. 2 Place a single original face down on the scanner glass.
7 Basic printing This chapter explains common printing tasks. Printing a document Your machine allows you to print from various Windows, Macintosh1, or Linux applications. The exact steps for printing a document may vary depending on the application you use. For details about printing, see the Software Section. Canceling a print job If the print job is waiting in a print queue or print spooler, such as the printer group in Windows, delete the job as follows: 1 Click the Windows Start menu.
8 Scanning Scanning to an application using a local connection Scanning with your machine lets you turn pictures and text into digital files that can be stored on your computer. Then you can fax or email the files, upload them to your website, or use them to create projects that you can print.
Note Scanning using a network connection You can change the scanner properties of your machine and the scan settings from the Samsung Network Scan Manager window. Click Properties and set the options in each tab. If you have connected your machine to a network and set up network parameters correctly, you can scan and send images over the network.
4 Click Add. 13 Enter the domain name of the SMB server. 5 Select the index number, from 1 to 20. 6 Enter a name in Alias for the Setup for the corresponding Server List entry. This name will be displayed on your machine. 14 Enter the location the scanned image will be stored. This is the location you have entered in the step 6. 7 Select IP Address or Host Name. 8 Enter the server address in dotted decimal notation or as a host name. 9 Enter the server port number, from 1 to 65535.
Setting network scan timeout 9 If the Network Scan program on your computer does not send a refresh request and does not scan a job within a specified timeout period, your machine cancels the scan job. You can change this timeout setting as needed. Press the Scroll buttons until the file format you want appears and press OK or Start. The machine begins scanning and then sends the email. 10 If the machine asks if you want to log off your account, press the Scroll buttons to select Yes or No and press OK.
Scanning to an SMB server 5 You can scan an image and then send it to an SMB server. You need to set up parameters for access to SMB servers from SyncThru™ Web Service. See page 8.3. Press the Scroll buttons until the desired status appears and press OK. 6 Repeat steps 4 and 5 to set other setting options. 7 When you have finished, press Stop/Clear to return to Standby mode. Before scanning, you can set the scan options for your scan job. See page 8.5.
Using Address Book entries Note You can also click Import and obtain your address book from your computer. To retrieve an email address, use the following ways: Speed email numbers Configuring group email numbers 1 Enter your machine’s IP address as the URL in a browser and click Go to access the web site of your machine. When you are prompted to enter a destination address while sending an email, enter the speed email number at which you stored the address you want.
Searching Address Book for an entry There are two ways to search for an address in memory. You can either scan from A to Z sequentially or search by entering the first letters of the name associated with the address. Searching sequentially through memory 1 If necessary, press Scan/Email. 2 Press Address Book until Search&Send appears on the bottom line of the display and press OK. 3 Press the Scroll buttons until the number category you want appears and press OK. 4 Press OK when All appears.
9 Faxing Sending a fax (SCX-5530FN only) The fax feature is available only on the SCX-5530FN. This chapter gives you information about using your machine as a fax machine. Setting the fax header This chapter includes: In some countries, you are required by law to indicate your fax number on any fax you send. The Machine ID, containing your telephone number and name or company name, will be printed at the top of each page sent from your machine.
Recommended resolution settings for different original document types are described in the table below: Mode Sending a fax automatically Recommended for: Standard Originals with normal sized characters. Fine Originals containing small characters or thin lines or originals printed using a dot-matrix printer. Super Fine Originals containing extremely fine detail. Super Fine mode is enabled only if the machine with which you are communicating also supports the Super Fine resolution. 1 Press Fax.
Receiving a fax Confirming a transmission When the last page of your original has been sent successfully, the machine beeps and returns to Standby mode. Selecting the paper tray When something goes wrong while sending your fax, an error message appears on the display. For a list of error messages and their meanings, see page 14.7. If you receive an error message, press Stop/Clear to clear the message and try to send the fax again.
7 Press Stop/Clear to return to Standby mode. Receiving automatically in Ans/Fax mode Notes To use this mode, you must attach an answering machine to the EXT socket on the back of your machine. • When the memory is full, the printer can no longer receive any incoming fax. Secure free memory to resume by removing data stored in the memory. • To use the Ans/Fax mode, attach an answering machine to the EXT socket on the back of your machine.
5 Call your fax number from another telephone. It is not necessary to place the call from a fax machine. 6 When your machine begins to ring, do not answer the call. The machine requires several rings to learn the pattern. Printing received faxes When the machine completes learning, the display shows Completed DRPD Setup. 1 Access the Secure Receive menu by following steps 1 through 3 in “Activating secure receiving mode”. 2 Press the Scroll buttons until Print appears and press OK.
Other ways to fax Printing received faxes on both sides of paper By using the Duplex button on your machine, you can set the machine to print received faxes on both sides of paper. 1 Press Duplex. 2 Press the Scroll buttons until the binding option you want appears. Sending a fax to multiple destinations You can use the Multiple Send feature, which allows you to send a fax to multiple locations. Originals are automatically stored in memory and sent to a remote station.
Adding pages to a delayed fax Sending a delayed fax You can add pages to the delayed transmissions previously reserved in your machine’s memory. You can set your machine to send a fax at a later time when you will not be present. 1 Press Fax. 2 Load originals face up into the ADF, or place a single original face down on the scanner glass. For details about loading an original, see page 5.1. 1 Load the originals to be added and adjust document settings.
8 9 Enter the job name you want and press OK. Subsequent sent faxes will be forwarded to the specified email address. The original is scanned into memory before transmission. The display shows memory capacity and the number of pages being stored in memory. 9 Press Stop/Clear to return to Standby mode. Forwarding received faxes to another fax machine If an original is placed on the scanner glass, select Yes to add another page. Load another original and press OK.
10 Fax setup Option (SCX-5530FN only) This chapter gives you information on setting up your machine for receiving and sending faxes. Sent Report You can set your machine to print a confirmation report showing whether a transmission was successful, how many pages were sent, and more. The available options are On, Off, and On-Error, which prints only when a transmission is not successful.
Option Auto Reduction Discard Size Description When receiving a fax containing pages as long as or longer than the paper loaded in the paper tray, the machine can reduce the size of the original to fit the size of the paper loaded in the machine. Turn on this feature if you want to automatically reduce an incoming page. With this feature set to Off, the machine cannot reduce the original to fit onto one page. The original will be divided and printed in actual size on two or more pages.
Registering after pressing a speed button 5 Enter the name you want and press OK. For details on how to enter alphanumeric characters, see page 2.3. 1 Press Fax. 2 Press one of the speed buttons. 6 Enter the fax number you want and press OK. 3 Press OK when Yes appears. 7 Press Stop/Clear to return to Standby mode. 4 Enter the name you want and press OK. Editing speed dial numbers For details on how to enter alphanumeric characters, see page 2.3.
8 When you have finished, press the Scroll buttons to select No at the Another No.? prompt and press OK. 9 Press Stop/Clear to return to Standby mode. Searching with a particular first letter 1 If necessary, press Fax. 2 Press Address Book until Search&Dial appears on the bottom line of the display and press OK. You can delete a specific entry from a group or add a new number to the selected group. 3 Press the Scroll buttons until the number category you want appears and press OK.
11 Using USB flash memory Note There are two USB plug types. (SCX-5530FN only) This chapter explains how to use a USB memory device with your machine. This chapter includes: • About USB memory • Plugging in a USB memory device • Scanning to a USB memory device • Printing from a USB memory device • Backing up data • Managing USB memory Insert a USB memory device into the USB memory port on the front of your machine.
5 Press OK or Start when USB appears. Printing from a USB memory device Your machine begins scanning the original, and then asks if you want to scan another page. 6 You can directly print files stored on a USB memory device. You can print TIFF, BMP, JPEG, PDF, and PRN files. Press OK when Yes appears to scan more pages. Load an original and press Start. Direct Print option supported file types: • PRN: Samsung PCL 6 compatible. Otherwise, press the Scroll buttons to select No and press OK.
Printing on both sides of paper Restoring data By using the Duplex button on your machine, you can set the machine to print documents on both sides of paper. 1 Insert the USB memory device on which the backup data is stored in to the USB memory port. 1 Press Duplex. 2 2 Press the Scroll buttons until the binding option you want appears. Press Menu until System Setup appears on the bottom line of the display and press OK. • Off: Prints in Normal mode. 3 Press OK when Machine Setup appears.
7 Press OK when Yes appears to confirm your selection. 8 Press Stop/Clear to return to Standby mode. Formatting a USB memory device 1 Insert the USB memory device into the USB memory port on your machine. 2 Press Scan/Email. 3 Press OK when Scan to USB appears on the bottom line of the display. 4 Press the Scroll buttons until File Manage appears and press OK. 5 Press the Scroll buttons until Format appears and press OK. 6 Press OK when Yes appears to confirm your selection.
12 Ordering supplies and Accessories accessories You can purchase and install accessories to enhance your machine’s performance and capacity. This chapter provides information on purchasing toner cartridges and accessories available for your machine. The following accessories are available for your machine: Toner cartridges Accessory Description Optional tray If you are experiencing frequent paper supply problems, you can attach an additional 250 sheet tray.
13 Maintenance This chapter provides information for maintaining your machine and the toner cartridge. This chapter includes: • Printing reports • Clearing memory • Cleaning your machine • Maintaining the toner cartridge • Maintenance Parts • Managing your machine from the website • Checking the machine’s serial number Your machine can provide various reports with useful information you will need.
Clearing memory Cleaning your machine You can selectively clear information stored in your machine’s memory. To maintain print and scan quality, follow the cleaning procedures below each time the toner cartridge is replaced or if print and scan quality problems occur. Caution For SCX-5530FN users, before clearing the memory, make sure that all fax jobs have been completed, or you will lose those jobs. 1 Press Menu until System Setup appears on the bottom line of the display and press OK.
3 Cleaning the scan unit With a dry lint-free cloth, wipe away any dust and spilled toner from the toner cartridge area and the toner cartridge cavity. Keeping the scan unit clean helps ensure the best possible copies. We suggest that you clean the scan unit at the start of each day and during the day, as needed. 1 Slightly dampen a soft lint-free cloth or paper towel with water. 2 Open the scanner lid. 3 Wipe the surface of the scanner glass and ADF glass until it is clean and dry.
Expected cartridge life 3 The life of the toner cartridge depends on the amount of toner that print jobs require. When printing text at ISO 19752 5% coverage, a new toner cartridge lasts an average of either 8,000 or 4,000 pages. (The original toner cartridge supplied with the machine lasts an average of 4,000 pages.
5 Close the front cover. Make sure that the cover is securely closed. 3 Remove the new toner cartridge from its bag. 4 Remove the packing tape and roll the cartridge 5 or 6 items to distribute the toner. Thoroughly roll the cartridge to assure maximum copies per cartridge. Save the box and the plastic bag for shipping. Replacing the toner cartridge Note When the toner cartridge is completely empty: If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water.
Sending new toner notification (SCX-5530FN only) Clearing the Toner Empty Replace Toner message You can set your machine to automatically send a fax to your service company or dealer to notify them that your machine requires a new toner cartridge when the toner cartridge needs to be replaced. The fax number needs to be set by your dealer prior to using this feature, otherwise the machine cannot send a notification even though you turn this service on.
Checking replaceables Replacing the ADF rubber pad If you experience frequent paper jams or printing problems, check the number of pages the machine has printed or scanned. Replace the corresponding parts, if necessary. You will need to replace the ADF rubber pad when there seems to be a consistent problem with paper pickup or when its specified yield is reached. The following information are available for checking the replaceable elements of your machine: 1 Open the ADF cover.
5 Align the left end of the ADF roller with the slot and push the right end of the roller into the right slot. Rotate the bushing on the right end of the roller toward the document input tray. Checking the machine’s serial number When you call for service or register as a user on the Samsung website, the machine’s serial number may be required. You can check the serial number by taking the following steps: 6 1 Press Menu until System Setup appears on the bottom line of the display and press OK.
14 Troubleshooting 3 Pull the jammed paper gently out of the ADF. This chapter gives helpful information for what to do if you encounter an error. This chapter includes: • Clearing document jams • Clearing paper jams • Understanding display messages • Solving other problems Clearing document jams When an original jams while passing through the ADF, Document Jam appears on the display. Note Caution If you do not see the paper in this area, refer to Roller misfeed. See page 14.2.
Roller misfeed In the tray 1 1 Open the scanner lid. 1 2 Seize the misfed paper, and remove the paper from the feed area by carefully pulling it to the right using both hands. Open and close the front cover. The jammed paper is automatically ejected from the machine. If the paper does not exit, go to the next step. 2 Pull the tray 1 open. 3 Remove the jammed paper by gently pulling it straight out. 1 1 3 scanner lid Close the scanner lid. Then load the removed pages back into the ADF.
In the optional tray 2 In the multi-purpose tray 1 Pull the optional tray 2 open. 1 If the paper is not feeding properly, pull the paper out of the machine. 2 Remove the jammed paper from the machine. 2 Open and close the front cover to resume printing. In the fuser area or around the toner cartridge If the paper does not move when you pull, or if you do not see the paper in this area, stop and go to step 3. 3 Pull the tray 1 half. 4 Pull the paper straight up and out.
2 Remove the jammed paper by gently pulling it straight out. 4 If you see the jammed paper, push the pressure lever on each side up and remove the paper. Skip to step 9. 1 3 Replace the toner cartridge and close the front cover. Printing automatically resumes. 1 If you still do not see the paper, go to the next step. In the paper exit area 1 Open and close the front cover. The jammed paper is automatically ejected from the machine. 2 Gently pull the paper out of the output tray.
6 8 Unfold the duplex guide fully. Pull the jammed paper out. If the jammed paper does not move when you pull, push the pressure lever on each side up to loose the paper, and then remove it. 1 1 1 7 duplex guide While pushing the fuser lever to the right, open the fuser door. 1 9 pressure lever Return the lever, door, stopper, and guide to their original position. 10 Close the rear cover. Printing automatically resumes.
2 Remove the jammed paper from the duplex unit. 3 Pull the jammed paper out. If the paper does not come out with the duplex unit, remove the paper from the bottom of the machine. Tips for avoiding paper jams By selecting the correct media types, most paper jams can be avoided. When a paper jam occurs, follow the steps outlined on page 14.2. • Follow the procedures on page 5.5. Ensure that the adjustable guides are positioned correctly. • Do not overload the tray.
Understanding display messages Message Meaning Suggested solutions Duplex Jam 0 Check Inside Paper has jammed during duplex printing. Clear the jam. See page 14.5. Note Duplex Jam 1 Open/Close Door Clear the jam. See page 14.6. When you call for service, it is very convenient to tell the service representative the display message. Paper has jammed during duplex printing. Enter Again You entered an unavailable item. Enter the correct item again.
Message Meaning Suggested solutions Global Server Auth Failed When there is a authentication fail while connecting to the global server this message displays. Check the authentication account and password. Global Server Comm. Error This error message displays when there is a communication error between the global server and the device. • Try again. • Contact a LDAP Server administrator. Global Server Not Configured When no global server is configured, this message displays.
Message Open Heat Error Cycle Power Meaning There is a problem in the fuser unit. Suggested solutions Message Unplug the power cord and plug it back in. If the problem persists, please call for service. Send Error (DNS) Send Error Meaning Suggested solutions There is a problem in DNS. Configure the DNS setting. Configure the POP3 setting. Operation Not Assigned You are in the Add Page/Cancel Job operation, but there are no jobs stored. Check the display to see if there are any scheduled jobs.
Toner cartridge-related messages Message Meaning Suggested solutions Install Toner A toner cartridge is not installed. Install a toner cartridge. Invalid Toner The toner cartridge you have installed is not for your printer. Install a Samsung-genuine toner cartridge, designed for your printer. Toner Low The toner cartridge is almost empty. Take out the toner cartridge and thoroughly shake it. By doing this, you can temporarily reestablish printing operations.
Solving other problems The following chart lists some conditions that may occur and the recommended solutions. Follow the suggested solutions until the problem is corrected. If the problem persists, please call for service. Paper feeding problems Condition Clear the paper jam. See page 14.2. Paper sticks together. • Ensure that there is not too much paper in the tray. The tray can hold up to 250 sheets of paper, depending on the thickness of your paper.
Condition Possible cause Suggested solutions For many software applications, the paper source selection is found under the Paper tab within the printer properties. Select the correct paper source. See the printer driver help screen. The machine selects print materials from the wrong paper source. The paper source selection in the printer properties may be incorrect. A print job is extremely slow. The job may be very complex.
If the inside of the machine is dirty or paper has been loaded improperly, you may notice a reduction in print quality. See the table below to clear the problem. Condition Light or faded print AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc Dropouts AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc Vertical lines If a vertical white streak or faded area appears on the page: • The paper may not meet specifications; for example, the paper is too moist or too rough. See page 5.8. • The transfer roller may be dirty.
Condition Suggested solutions Condition Background scatter Background scatter results from bits of toner randomly distributed on the printed page. • The paper may be too damp. Try printing with a different batch of paper. Do not open packages of paper until necessary so that the paper does not absorb too much moisture. • If background scatter occurs on an envelope, change the printing layout to avoid printing over areas that have overlapping seams on the reverse side.
Condition Horizontal stripes AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc Curl An unknown image repetitively appears on a next few sheets or loose toner, light print, or contamination occurs. Suggested solutions Copying problems If horizontally aligned black streaks or smears appear: • The toner cartridge may be installed improperly. Remove the cartridge and reinsert it. • The toner cartridge may be defective. Remove the toner cartridge and install a new one. See page 13.5.
Scanning problems Condition Suggested solutions The scanner does not work. • Make sure that you place the original to be scanned face down on the scanner glass, or face up in the ADF. • There may not be enough available memory to hold the document you want to scan. Try the Prescan function to see if that works. Try lowering the scan resolution rate. • Check that the USB or parallel cable is connected properly. • Make sure that the USB or parallel cable is not defective.
Network Scan problems Condition Condition Suggested solutions I cannot find a scanned image file. You can check the scanned file’s destination in the Advanced page in the Network Scan program’s Properties screen. I cannot find the scanned image file after scanning. • Check if the scanned file’s application is on your computer.
Common Windows problems Condition Suggested solutions “File in Use” message appears during installation. Exit all software applications. Remove all software from the StartUp Group, then restart Windows. Reinstall the printer driver. “Error Writing to LPTx” message appears. • Ensure that the cables are connected correctly, the machine is on. • If bi-directional communication is not turned on in the driver, it will also cause this message.
Common Linux problems Problem Possible Cause and Solution The machine does not print • Check if the printer driver is installed in your system. Open Unified Driver configurator and switch to the Printers tab in Printers configuration window to look at the list of available printers. Make sure that your machine is displayed on the list. If not, please, invoke Add new printer wizard to set up your device. • Check if the printer is started.
Problem Possible Cause and Solution The machine does not scan • Check if a document is loaded into the machine. • Check if your machine is connected to the computer. Make sure if it is connected properly if I/O error is reported while scanning. • Check if the port is not busy. Since functional components of MFP (printer and scanner) share the same I/O interface (port), the situation of simultaneous access of different “consumer” application to the same port is possible.
15 Installing accessories 2 Grasp the control board cover and slide toward you to open it. Your machine is a full-featured one that has been optimized to meet most of your printing needs. Recognizing that each user may have different requirements, however, Samsung makes several accessories available to enhance your machine’s capabilities.
6 Activating the added memory in the PS printer properties (SCX-5530FN only) Push the DIMM straight into the DIMM slot until it snaps into place. Make sure the latches fit over the notches located on either side of the DIMM. After installing the memory DIMM, you need to select it in the printer properties of the PostScript printer driver so that you can use it. 7 1 Make sure that the PostScript printer driver is installed on your computer.
16 Specifications Item This chapter includes: • General specifications • Scanner and copier specifications • Printer specifications • Facsimile specifications (SCX-5530FN only) General specifications Item Up to 50 sheets (75 g/m2) ADF document size Width: 142 to 216 mm External dimension (W x D x H) 466 x 435.4 x 458 mm Weight (including consumables) SCX-5330N : 18.1 Kg (39.9 lb) Package weight Paper: 2.8 Kg (6.17 lb) Plastic: 0.7 Kg (1.
Scanner and copier specifications Item Facsimile specifications (SCX-5530FN only) Description Item Description Compatibility TWAIN standard / WIA standard Compatibility ITU-T Group 3 Scanning method ADF and Flat-bed Color CCD (Charge Coupled Device) module Applicable line Public Switched Telephone Network (PSTN) or behind PABX Resolution Optical: 600 x 1,200 dpi (mono and color) Enhanced: 4,800 x 4,800 dpi Data coding MH/MR/MMR/JPEG/ECM (Error Correction Mode) Effective scanning length Sca
INDEX Numerics D 2/4-up, special copy 6.2 date and time, set 2.2 default mode, change 2.2 delayed fax 9.7 DIMM, install 15.1 display language, change 2.2 DRPD (Distinctive Ring Pattern Detection) 9.4 drum, clean 13.5 jam, clear document 14.1 paper 14.2 job timeout, set 2.4 E K Erasing background, special copy 6.4 error messages 14.7 key sound 2.3 A accessories installing memory DIMM 15.1 order information 12.1 Address Book, use 8.5 ADF 1.2 ADF rubber pad, replace 13.7 ADF, load 5.1 alarm sound 2.
Network Scan 14.17 paper feeding 14.11 PostScript errors 14.18 printing 14.11 scanning 14.16 Windows 14.18 operating systems 4.1 TCP/IP 4.1 new toner notification, send 13.6 n-up (multiple pages per sheet) copying 6.2 O originals jam, clear 14.1 loading 5.1 output location, select 5.8 output tray 5.8 P paper guidelines 5.4 paper jam, clear duplex area 14.5 fuser area or around toner cartridge 14.3 multi-purpose tray 14.3 optional tray 2 14.3 paper exit area 14.4 tray 1 14.2 paper level indicator 5.
Samsung Printer Software section
SOFTWARE SECTION CONTENTS Chapter 1: INSTALLING PRINTER SOFTWARE IN WINDOWS Installing Printer Software ........................................................................................................ 5 Installing Software for Local Printing ................................................................................. 5 Installing Software for Network Printing ............................................................................. 8 Reinstalling Printer Software ......................
Editing a Watermark ..................................................................................................... 22 Deleting a Watermark ................................................................................................... 22 Using Overlays ...................................................................................................................... 23 What is an Overlay? ......................................................................................................
Scanning Process with TWAIN-enabled Software ........................................................................ 31 Scanning Using the WIA Driver ................................................................................................ 31 Chapter 9: USING YOUR PRINTER IN LINUX Getting Started ..................................................................................................................... 32 Installing the Unified Linux Driver .............................................
1 Typical Installation Installing Printer Software in Windows This is recommended for most users. All components necessary for printer operations will be installed. This chapter includes: • Installing Printer Software 1 Make sure that the printer is connected to your computer and powered on. 2 Insert the supplied CD-ROM into your CD-ROM drive. The CD-ROM should automatically run, and an installation window appears.
7 NOTE: If your printer is not already connected to the computer, the following window will appear. To register yourself as a user of Samsung Printers in order to receive information from Samsung, select the checkbox and click Finish. You are now sent to the Samsung web site. Otherwise, just click Finish. • After connecting the printer, click Next. • If you don’t want to connect the printer at this time, click Next, and No on the following screen.
3 Click Next. • If necessary, select a language from the drop-down list. NOTE: If your printer is not already connected to the computer, the following window will appear. • View User’s Guide: Allows you to view the User’s Guide. If your computer doesn’t have Adobe Acrobat, click on this option and it will automatically install Adobe Acrobat Reader for you. 4 5 Select Custom installation. Click Next. • After connecting the printer, click Next.
9 To register yourself as a user of Samsung Printers in order to receive information from Samsung, select the checkbox and click Finish. You are now sent to the Samsung web site. If the installation window does not appear, click Start and then Run. Type X:\Setup.exe, replacing “X” with the letter which represents your drive and click OK. Otherwise, just click Finish. 3 Click Next. • If necessary, select a language from the drop-down list. • View User’s Guide: Allows you to view the User’s Guide.
5 Custom Installation The list of printers available on the network appears. Select the printer you want to install from the list and then click Next. You can choose individual components to install and set a specific IP address. 1 Make sure that the printer is connected to your network and powered on. For details about connecting to the network, see the supplied printer’s User’s Guide. 2 Insert the supplied CD-ROM into your CD-ROM drive.
5 6 The list of printers available on the network appears. Select the printer you want to install from the list and then click Next. • If you do not see your printer on the list, click Update to refresh the list, or select Add TCP/IP Port to add your printer to the network. To add the printer to the network, enter the port name and the IP address for the printer. Select the components to be installed. After selecting the components, the following window appears.
Reinstalling Printer Software NOTE: If your printer is not already connected to the computer, the following window will appear. You can reinstall the software if installation fails. 1 Start Windows. 2 3 4 From the Start menu select Programs or All Programs →your printer driver name →Maintenance. Select Repair and click Next. The list of printers available on the network appears. Select the printer you want to install from the list and then click Next. • After connecting the printer, click Next.
Removing Printer Software 1 2 3 4 5 6 Start Windows. From the Start menu select Programs or All Programs →your printer driver name →Maintenance. Select Remove and click Next. You will see a component list so that you can remove any item individually. Select the components you want to remove and then click Next. When your computer asks you to confirm your selection, click Yes. The selected driver and all of its components are removed from your computer. After the software is removed, click Finish.
2 1 2 Basic Printing This chapter explains the printing options and common printing tasks in Windows. Open the document you want to print. Select Print from the File menu. The Print window is displayed. It may look slightly different depending on your application. The basic print settings are selected within the Print window. These settings include the number of copies and print range.
Layout Tab Printer Settings The Layout tab provides options to adjust how the document appears on the printed page. The Layout Options includes Multiple Pages per Side and Poster Printing. See “Printing a Document” on page 13 for more information on accessing printer properties. You can use the printer properties window, which allows you to access all of the printer options you need when using your printer.
Paper Tab 3 Source Make sure that Source is set to the corresponding paper tray. Use Manual Feed when printing on special materials like envelopes and transparencies. You have to load one sheet at a time into the Manual Tray or Multi-Purpose Tray.
Graphics Tab Advanced Options Use the following Graphic options to adjust the print quality for your specific printing needs. See “Printing a Document” on page 13 for more information on accessing printer properties. You can set advanced settings by clicking the Advanced Options button. • TrueType Options: This option determines what the driver tells the printer about how to image the text in your document. Select the appropriate setting according to the status of your document.
Extras Tab About Tab You can select output options for your document. See “Printing a Document” on page 13 for more information about accessing the printer properties. Use the About tab to display the copyright notice and the version number of the driver. If you have an Internet browser, you can connect to the Internet by clicking on the web site icon. See “Printing a Document” on page 13 for more information about accessing printer properties.
Using a Favorite Setting The Favorites option, which is visible on each properties tab, allows you to save the current properties settings for future use. To save a Favorites item: 1 2 Change the settings as needed on each tab. 3 Click Save. Enter a name for the item in the Favorites input box. When you save Favorites, all current driver settings are saved. To use a saved setting, select the item from the Favorites drop down list.
3 Advanced Printing Printing Multiple Pages on One Sheet of Paper (N-Up Printing) This chapter explains printing options and advanced printing tasks. 1 2 3 4 NOTE: • Your printer driver Properties window that appears in this User’s Guide may differ depending on the printer in use. However the composition of the printer properties window is similar. • If you need to know the exact name of your printer, you can check the supplied CD-ROM.
Printing Posters Printing Booklets This feature allows you to print a single-page document onto 4, 9, or 16 sheets of paper, for the purpose of pasting the sheets together to form one poster-size document. 1 2 3 8 To change the print settings from your software application, access printer properties. See “Printing a Document” on page 13. Click the Layout tab, select Poster Printing in the Layout Type drop-down list.
Printing on Both Sides of Paper Printing a Reduced or Enlarged Document You can print on both sides of a sheet of paper. Before printing, decide how you want your document oriented. You can change the size of a page’s content to appear larger or smaller on the printed page. The options are: • Printer Setting, if you select this option, this feature is determined by the setting you’ve made on the control panel of the printer. If this option does not appear, 1 your printer does not have this feature.
Editing a Watermark Using Watermarks 1 The Watermark option allows you to print text over an existing document. For example, you may want to have large gray letters reading “DRAFT” or “CONFIDENTIAL” printed diagonally across the first page or all pages of a document. 2 There are several predefined watermarks that come with the printer, and they can be modified, or you can add new ones to the list.
Using a Page Overlay Using Overlays After an overlay has been created, it is ready to be printed with your document. To print an overlay with a document: 1 2 What is an Overlay? Dear ABC Regards WORLD BEST An overlay is text and/or images stored in the computer hard disk drive (HDD) as a special file format that can be printed on any document. Overlays are often used to take the place of preprinted forms and letterhead paper.
4 Advanced Using Windows PostScript Driver You can use advanced settings by clicking the Advanced button. If you want to use the PostScript driver provided with your system CD-ROM to print a document. PPDs, in combination with the PostScript driver, access printer features and allow the computer to communicate with the printer. An installation program for the PPDs is provided on the supplied software CD-ROM.
5 Using Direct Print Utility Printing There are several ways you can print using Direct Print Utility. This chapter explains how to use Direct Print Utility to print PDF files without having to open the files. From the Direct Print Utility window CAUTION • You can not print PDF files that are restricted to print. Deactivate the printing restriction feature, and retry printing. 1 From the Start menu select Programs or All Programs → Direct Print Utility →Direct Print Utility.
6 Sharing the Printer Locally Setting Up a Host Computer 1 2 3 4 5 6 You can connect the printer directly to a selected computer, which is called “host computer,” on the network. The following procedure is for Windows XP. For other Windows OS, refer to the corresponding Windows User's Guide or online help. NOTES: • Check the Operating System(s) that are compatible with your printer. Please refer to the OS Compatibility section of Printer Specifications in your Printer User’s Guide.
7 If you are a Windows user, from the Start menu, select Programs or All Programs →your printer driver name → Smart Panel. Using Smart Panel Smart Panel is a program that monitors and informs you of the status of the printer, and allows you to customize the printer’s settings. Smart Panel is installed automatically when you install the printer software.
5 Driver Setting (Only for Windows) You can use the printer properties window, which allows you to access all of the printer options you need for using your printer. For details, See “Printer Settings” on page 14. Changing the Smart Panel Program Settings Right-click (in Windows or Linux) or click (in Mac OS X) the Smart Panel icon and select Options. The following window opens. Opening the Troubleshooting Guide Using the troubleshooting guide, you can view solutions for error status problems.
8 Scanning Scanning Using Samsung SmarThru Scanning with your machine lets you turn pictures and text into digital files on your computer. Then you can fax or e-mail the files, display them on your web site or use them to create projects that you can print using Samsung SmarThru software or the WIA driver. Samsung SmarThru is the accompanying software for your machine. With SmarThru, scanning is the proverbial piece of cake. This chapter includes: NOTE: You can use SmarThru 4 in Windows 98 or higher.
Using Samsung SmarThru 4 Follow these steps to start scanning using the SmarThru: 1 Make sure that your machine and computer are turned on and properly connected to each other. 2 Place your photograph or page on the document glass or ADF. 3 Once you have installed Samsung SmarThru, you will see the SmarThru 4 icon on your desktop. Double-click the SmarThru 4 icon. Click Scan To. The Scan To menu bar appears on the SmarThru 4 window. Scan To menu bar Adjust the scan settings.
•Settings Scanning Using the WIA Driver Customizing settings of Scan To basic functions. Allows you to customize settings for Application, E-mail, OCR, and Web functions. 5 Click the service icon according to your job. 6 SmarThru 4 opens for the selected service. Adjust the scan settings. 7 To start scanning, click Scan. Your machine also supports the Windows Image Acquisition (WIA) driver for scanning images.
9 Using Your Printer in Linux Installing the Unified Linux Driver You can use your machine in a Linux environment. Installing the Unified Linux Driver 1 This chapter includes: • Getting Started 2 • Installing the Unified Linux Driver Make sure that you connect your machine to your computer. Turn both the computer and the machine on. When the Administrator Login window appears, type in root in the Login field and enter the system password.
5 Uninstalling the Unified Linux Driver When the installation is complete, click Finish. 1 When the Administrator Login window appears, type in root in the Login field and enter the system password. NOTE: You must log in as a super user (root) to install the printer software. If you are not a super user, ask your system administrator. 2 Insert the printer software CD-ROM. The CD-ROM will automatically run. If the CD-ROM does not automatically run, click the icon at the bottom of the desktop.
Printers Configuration Using the Unified Driver Configurator Printers configuration has the two tabs; Printers and Classes. Printers Tab You can see the current system’s printer configuration by clicking on the printer icon button on the left side of the Unified Driver Configurator window. Unified Linux Driver Configurator is a tool primarily intended for configuring Printer or MFP devices.
Classes Tab Ports Configuration The Classes tab shows a list of available printer classes. In this window, you can view the list of available ports, check the status of each port and release a port that is stalled in busy state when its owner is terminated for any reason. Shows all of the printer classes. Switches to ports configuration. Shows the status of the class and the number of printers in the class. Shows all of the available ports.
Configuring Printer Properties Printing a Document Using the properties window provided by the Printers configuration, you can change the various properties for your machine as a printer. 1 Open the Unified Driver Configurator. Printing from Applications 2 3 There are a lot of Linux applications that you are allowed to print from using Common UNIX Printing System (CUPS). You can print on your machine from any such application. 1 From the application you are using, select Print from the File menu.
5 6 7 The following four tabs display at the top of the window. •General - allows you to change the paper size, the paper type, and the orientation of the documents, enables the duplex feature, adds start and end banners, and changes the number of pages per sheet. •Text - allows you to specify the page margins and set the text options, such as spacing or columns. •Graphics - allows you to set image options that are used when printing images/files, such as color options, image size, or image position.
10 When you are finished, click Save on the toolbar. 11 Select the file directory where you want to save the image The document is scanned and the image preview appears in the Preview Pane. and enter the file name. 12 Click Save. Adding Job Type Settings You can save your scan option settings to retrieve for a later scanning. To save a new Job Type setting: 1 Change the options from the Scanner Properties window. Drag the pointer to set the image area to be scanned. 2 3 4 Click Save As.
You can use the following tools to edit the image: Tools Function Saves the image. Cancels your last action. Restores the action you canceled. Allows you to scroll through the image. Crops the selected image area. Zooms the image out. Zooms the image in. Allows you to scale the image size; you can enter the size manually, or set the rate to scale proportionally, vertically, or horizontally. Allows you to rotate the image; you can select the number of degrees from the dropdown list.
1 0 Using Your Printer with a Macintosh (SCX-5530FN only) Installing Software for Macintosh The PostScript driver CD-ROM that came with your machine provides you with the PPD file to use the PS driver, Apple LaserWriter driver, for printing on a Macintosh computer. Your machine supports Macintosh systems with a built-in USB interface or a 10/100 Base-TX network interface card. When you print a file from a Macintosh computer, you can use the PostScript driver by installing the PPD file.
Install the Scan driver 1 2 3 Setting Up the Printer Make sure that you connect your printer to the computer. Turn on your computer and printer. Insert the CD-ROM which came with your printer into the CD-ROM drive. Double-click CD-ROM icon that appears on your Macintosh desktop. Double-click the MAC_Installer folder. Set up for your printer will be different depending on which cable you use to connect the printer to your computer—the network cable or the USB cable. 4 5 Double-click the Twain folder.
Changing Printer Settings Printing You can use advanced printing features when using your printer. From your Macintosh application, select Print from the File menu. The printer name which appears in the printer properties window may differ depending on the printer in use. Except for the name, the composition of the printer properties window is similar. NOTES: • The Macintosh printer’s properties window that appears in this User’s Guide may differ depending on the printer in use.
Printing Multiple Pages on One Sheet of Paper Printer Features Setting The Printer Features tab provides options for selecting the paper type and adjusting print quality. You can print more than one page on a single sheet of paper. This feature provides a cost-effective way to print draft pages. Select Printer Features from the Presets drop-down list to access the following features: 1 2 From your Macintosh application, select Print from the File menu. Select Layout. ▲ Mac OS 10.
Duplex Printing Scanning You can print on both sides of the paper. Before printing in the duplex mode, decide on which edge you will be binding your finished document. The binding options are: If you want to scan documents using other software, you will need to use TWAIN-compliant software, such as Adobe PhotoDeluxe or Adobe Photoshop. The first time you scan with your machine, select it as your TWAIN source in the application you use.
SOFTWARE SECTION INDEX A L advanced printing, use 19 Layout properties, set Macintosh 42 Windows 14 Linux driver, install 32 printer properties 36 printing 36 scanning 37 B booklet printing 20 C canceling scan 31 D document, print Macintosh 42 Windows 13 double-sided printing 21 M Macintosh driver install 40 printing 42 scanning 44 setting up the printer 41 MFP driver, install Linux 32 E Extras properties, set 17 N F n-up printing Macintosh 43 Windows 19 favorites settings, use 18 G O help,
R resolution printing 37 S scanning Linux 37 SmarThru 29 TWAIN 31 WIA driver 31 scanning from Macintosh 44 setting darkness 16 favorites 18 image mode 16 resolution Macintosh 43 Windows 16 toner save 16 true-type option 16 software install Macintosh 40 Windows 5 reinstall Windows 11 system requirements Macintosh 40 uninstall Windows 12 status monitor, use 27 T toner save, set 16 TWAIN, scan 31 U uninstall, software Windows 12 uninstalling MFP driver Linux 33 W watermark create 22 delete 22 edit 22 print
