SCX-4725F SCX-4725FN
© 2006 Samsung Electronics Co., Ltd. All rights reserved. This manual is provided for information purposes only. All information included herein is subject to change without notice. Samsung Electronics is not responsible for any direct or indirect damages, arising from or related to use of this manual. • SCX-4725F and SCX-4725FN are model names of Samsung Electronics Co., Ltd. • Samsung and Samsung logo are trademarks of Samsung Electronics Co., Ltd.
CONTACT SAMSUNG WORLDWIDE If you have any comments or questions regarding Samsung products, contact the Samsung customer care center. Country Customer Care Center Web Site Country Customer Care Center Web Site LITHUANIA 8-800-77777 www.samsung.com/lt ARGENTINE 0800-333-3733 www.samsung.com/ar LUXEMBURG 0035 (0)2 261 03 710 www.samsung.com/be AUSTRALIA 1300 362 603 www.samsung.com/au MALAYSIA 1800-88-9999 www.samsung.com/my AUSTRIA 0800-SAMSUNG (726-7864) www.samsung.
CONTENTS 1. Introduction Special features ...................................................................................................................................................... 1.1 Printer overview ...................................................................................................................................................... 1.2 Finding more information ......................................................................................................................
8. Scanning Scanning basics ...................................................................................................................................................... 8.1 Scanning to an application ...................................................................................................................................... 8.1 9. Faxing Setting the fax header .................................................................................................................................
14. Specifications General specifications ........................................................................................................................................... 14.1 Printer specifications ............................................................................................................................................. 14.1 Scanner and copier specifications ........................................................................................................................
Important Precautions and Safety Information 17 The Power cord supplied with your machine should be used for safe operation. If you are using a cord which is longer than 2 m with 110 V machine, then it should be 16 AWG1 or bigger. When using this machine, these basic safety precautions should always be followed to reduce risk of fire, electric shock and injury to people: 1 Read and understand all instructions. 18 Use only No.26 AWG* or larger telephone line cord.
Mercury Safety television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or experienced radio TV technician for help.
EC Certification WARNING: FCC Regulations state that changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. In the event that terminal equipment causes harm to the telephone network, the telephone company should notify the customer that service may be stopped.
iv
1 Introduction Print in various environments • You can print with Windows 98/Me/2000/XP(32/64bit)/ 2003(32/64bit). • Your machine is compatible with a variety of Linux systems. • Your machine is compatible with a variety of Macintosh systems (SCX-4725FN only). • Zoran IPS Emulation* compatible with PostScript 3 (PS) enables PS printing (SCX-4725FN only). Thank you for purchasing this Samsung multifunctional product. Your machine provides printing, copying, scanning, and faxing functions.
Printer overview These are the main components of your machine: Front view Rear view * The figure above shows an SCX-4725FN. * The figure above shows an SCX-4725FN.
Control panel overview 1 Darkness: Adjusts the document brightness for the current copy job. 11 Start: Starts a job. 2 No. of Copies: Enters the number of copies. 12 Stop/Clear: Stops an operation at any time. In Standby mode, clears/cancels the copy options, such as the darkness, the document type setting, the copy size, and the number of copies. 3 Original Type: Selects the document type for the current copy job. 13 Number keypad: Dials a number or enters alphanumeric characters.
Finding more information Selecting a location You can find information for setting up and using your machine from the following resources, either printed or onscreen. Select a level, stable place with adequate space for air circulation. Allow extra space for opening covers and trays. Quick Install Guide The area should be well-ventilated and away from direct sunlight or sources of heat, cold, and humidity. Do not set the machine close to the edge of your desk or table.
2 System setup This chapter gives you an overview of menus available on your machine and step-by-step instructions for setting up the machine’s systems.
Note Changing the display language The date format may differ from country to country. To change the language that appears on the control panel, follow these steps: 1 Press Menu until Machine Setup appears on the top line of the display. 2 Press the Scroll buttons until Language appears and press Enter. 3 Press the Scroll buttons until the language you want appears and press Enter. 4 You can also use the Scroll buttons to move the cursor under the digit you want to correct and enter a new number.
Speaker, ringer, key sound, and alarm sound 1 Press Menu until Sound/Volume appears on the top line of the display. 2 Press the Scroll buttons until the sound option you want appears and press Enter. 3 Press the Scroll buttons until the desired status or volume for the sound you have selected appears and press Enter. 4 If necessary, repeat steps 2 through 3 to set other sounds. 5 Press Stop/Clear to return to Standby mode. Keypad letters and numbers Key Speaker volume 1 Press On Hook Dial.
Power Save mode Power Save mode allows your machine to reduce power consumption when it is not in actual use. You can select a length of time for which the machine waits after a job is printed before it switches to a reduced power state. 1 Press Menu until Machine Setup appears on the top line of the display. 2 Press the Scroll buttons until Power Save appears and press Enter. 3 Press the Scroll buttons until the time setting you want appears and press Enter.
3 Software overview CD PostScript printer driver CD This chapter gives you an overview of the software that comes with your machine. Further details about installing and using the software are explained in the Software Section. Supplied software • Printer driver features • System requirements Supplied software You must install the printer and scanner software using the supplied CDs after you have set up your machine and connected it to your computer.
Printer driver features System requirements Your printer drivers support the following standard features: • Paper source selection Before you begin, ensure that your system meets the following requirements: • Paper size, orientation and media type Windows • Number of copies Item In addition, you can use various special printing features.
Linux Item Requirements Operating system • • • • Red Hat 8.0 ~ 9.0 Fedora Core 1 ~ 4 Mandrake 9.2 ~ 10.1 SuSE 8.2 ~ 9.2 CPU Pentium IV 1 GHz or higher RAM 256 MB or higher Free disk space 1 GB or higher Software • • • • Linux Kernel 2.4 or higher Glibc 2.2 or higher CUPS SANE (for MFP device only) Notes • It is necessary to claim swap partition of 300 MB or larger for working with large scanned images. • The Linux scanner driver supports the optical resolution at maximum.
4 Network setup Via the control panel (SCX-4725FN only) You can set up the following basic network parameters through the machine’s control panel: Connecting your machine to a network is available only on the SCX-4725FN. This chapter gives you step-by-step instructions for setting up your machine for network connections.
Static addressing 3 Press the Scroll buttons until EtherTalk appears and press Enter. To enter a TCP/IP address from your machine’s control panel, take the following steps: 4 Press the Scroll buttons until On appears and press Enter. 5 Press Stop/Clear to return to Standby mode. 1 Press Menu until Network Setup appears on the top line of the display. 2 Press the Scroll buttons until Config Network appears and press Enter. 3 Press Enter when TCP/IP appears. 4 Press Enter when Manual appears.
2 Start Windows Explorer and open the X drive. (X represents your CD-ROM drive.) 3 Double click Application > SetIP. 4 Open the language folder you want to use. 5 Double click Setup.exe to install this program. 6 From the Windows Start menu, select Programs > Samsung Network Printer Utilities > SetIP. 7 Select the name of your printer and click " ". Note If you cannot find your printer name click " list.
5 Loading originals and print 2 Place the original face down on the scanner glass and align it with the registration guide at the top left corner of the glass. 3 Close the scanner lid. media This chapter introduces you to how to load originals and print media into your machine.
To load an original into the ADF: 1 Selecting print media Load the original face up into the ADF. Make sure that the bottom of the original stack matches the paper size marked on the document input tray. You can print on a variety of print media, such as plain paper, envelopes, labels, and transparencies. Always use print media that meet the guidelines for use with your machine.
Supported print media types and sizes Type Plain paper Size Dimensions Weight1 Capacity2 • 60 to 90 g/m2 (16 to 24 lb bond) for the tray • 60 to 165 g/m2 (16 to 43 lb bond) for the manual tray • 250 sheets of 75 g/m2 (20 lb bond) paper for the tray • 1 sheet for the manual tray 75 to 90 g/m2 (20 lb to 24 lb bond) 1 sheet for the manual tray Letter 216 x 279 mm (8.5 x 11 inches) Legal 216 x 356 mm (8.5 x 14 inches) Folio 216 x 330.2 mm (8.5 x 13 inches) Oficio 216 x 343 mm (8.5 x 13.
Media sizes supported in each mode Mode Size Guidelines for special print media Media type Source Copy mode Letter, A4, Legal, Folio, Executive, ISO B5, JIS B5, A5, A6 • tray • manual tray Print mode All sizes supported by the machine • tray • manual tray Fax mode Letter, A4, Legal • tray • manual tray Envelopes Guidelines for selecting and storing print media When selecting or loading paper, envelopes, or other print materials, keep these guidelines in mind: • Always use print media that conf
Media type Guidelines Transparencies • To avoid damaging the machine, use only transparencies designed for use in laser printers. • Transparencies used in the machine must be able to withstand 180 °C, the machine’s fusing temperature. • Place them on a flat surface after removing them from the machine. • Do not leave them in the paper tray for long periods of time. Dust and dirt may accumulate on them, resulting in spotty printing. • To avoid smudging caused by fingerprints, handle them carefully.
3 Load the paper with the side to be printed on facing up. Notes • If you experience problems with paper feed, place one sheet at a time in the manual tray. • You can load previously printed paper. The printed side should be facing down with an uncurled edge at the front. If you experience problems with paper feed, turn the paper around. Note that print quality is not guaranteed.
3 After loading paper, set the paper type and size for the manual tray. See the next section for copying and faxing or the Software Section for PC-printing. Verifying an output location The machine has a paper output location which holds 100 sheets of paper. Note The settings made from the printer driver override the settings on the control panel. Tips on using the manual tray • Load only one sheet of print media at a time in the manual tray.
6 Copying Changing the settings for each copy Your machine provides default settings for copying so that you can quickly and easily make a copy. However, if you want to change the options for each copy, use the copy function buttons on the control panel. This chapter gives you step-by-step instructions for copying documents.
Reduced or enlarged copy Using special copy features By using the Reduce/Enlarge button, you can reduce or enlarge the size of a copied image from 25% to 400% when you copy original documents from the scanner glass, or from 25% to 100% from the ADF. You can use the following copy features: To select from the predefined copy sizes: Clone copying 1 Press Reduce/Enlarge. 2 Press Reduce/Enlarge or the Scroll buttons until the size setting you want appears and press Enter.
Auto fit A 3 Press Start to begin copying. Your machine begins scanning the front side and shows Set BackSide. Your machine can automatically reduce or enlarge the original image to fit on the paper currently loaded in the machine. 4 Open the scanner lid and turn the original over. This copy feature is available only when you place originals on the scanner glass.
Poster copying Your machine can print an image onto 9 sheets of paper (3x3). You can paste the printed pages together to make one poster-sized document. This copy feature is available only when you place originals on the scanner glass. 1 Place a single original face down on the scanner glass. For details about loading an original, see page 5.1. 2 Press Favorite Copy until Poster appears on the bottom line of the display and press Enter. 3 Press Start to begin copying.
7 Basic printing This chapter explains common printing tasks. Printing a document Your machine allows you to print from various Windows, Macintosh1, or Linux applications. The exact steps for printing a document may vary depending on the application you use. For details about printing, see the Software Section. Canceling a print job If the print job is waiting in a print queue or print spooler, such as the printer group in Windows, delete the job as follows: 1 Click the Windows Start menu.
8 Scanning Scanning with your machine lets you turn pictures and text into digital files that can be stored on your computer. Then you can fax or email the files, upload them to your website, or use them to create projects that you can print. Scanning basics Your machine offers the following ways to scan an image: • Via one of the preset imaging applications. Scanning an image launches the selected application, enabling you to control the scanning process. See the next section.
9 Faxing Sending a fax This chapter gives you information about using your machine as a fax machine. Setting the fax header This chapter includes: In some countries, you are required by law to indicate your fax number on any fax you send. The Machine ID, containing your telephone number and name or company name, will be printed at the top of each page sent from your machine.
Recommended resolution settings for different original document types are described in the table below: Mode Sending a fax automatically 1 Recommended for: Standard Originals with normal sized characters. Fine Originals containing small characters or thin lines or originals printed using a dot-matrix printer. Super Fine Originals containing extremely fine detail. Super Fine mode is enabled only if the machine with which you are communicating also supports the Super Fine resolution.
Receiving a fax Confirming a transmission When the last page of your original has been sent successfully, the machine beeps and returns to Standby mode. Changing receiving modes When something goes wrong while sending your fax, an error message appears on the display. For a list of error messages and their meanings, see page 13.3. If you receive an error message, press Stop/Clear to clear the message and try to send the fax again. 1 Press Menu until Fax Setup appears on the top line of the display.
The machine begins receiving a fax and returns to Standby mode when the reception is completed. fax machine. Unless you change it, this ringing pattern will continue to be recognized and answered as a fax call, and all other ringing patterns will be forwarded to the extension telephone or answering machine plugged into the EXT socket. You can easily suspend or change DRPD at any time.
2 Press the Scroll buttons until Secure Receive appears and press Enter. 3 Press the Scroll buttons until On appears and press Enter. 4 Enter a four-digit password you want to use and press Enter. Then, as soon as you finish copying or printing, the machine automatically prints the fax. Note You can activate secure receiving mode without setting a password, but cannot protect your faxes. 5 Re-enter the password to confirm it and press Enter. 6 Press Stop/Clear to return to Standby mode.
Other ways to fax Sending a fax to multiple destinations 3 Press Menu until Fax Feature appears on the top line of the display. 4 Press Enter when DelayFax appears. 5 Enter the number of the receiving machine using the number keypad and press Enter. You can use speed dial numbers, or group dial numbers. For details, see page 10.3. You can use the Broadcasting button, which allows you to send a fax to multiple locations. Originals are automatically stored in memory and sent to a remote station.
Canceling a delayed fax 1 Press Menu until Fax Feature appears on the top line of the display. 2 Press the Scroll buttons until Cancel Job appears and press Enter. 3 Press the Scroll buttons until the fax job you want appears and press Enter. 4 Press 1 to select Yes. The selected fax job is deleted from memory. Sending a priority fax Using the Priority Fax feature, a high priority fax can be sent ahead of reserved operations.
10 Fax setup Option This chapter gives you information on setting up your machine for receiving and sending faxes. This chapter includes: • Redials You can specify the number of redial attempts. If you enter 0, the machine will not redial. MSG Confirm You can set your machine to print a report showing whether a transmission was successful, how many pages were sent, and more. The available options are On, Off, and On-Err, which prints only when a transmission is not successful.
Using the advanced fax features Printing sent fax report automatically To use the advanced fax options: 1 You can set the machine to print a report with detailed information about the previous 50 communication operations, including time and dates. Press Menu until Advanced Fax appears on the top line of the display. 1 Press Menu until Fax Setup appears on the top line of the display. 2 Press the Scroll buttons until the menu item you want appears and press Enter.
Group dial numbers Setting up Phone Book If you frequently send the same document to several destinations, you can group these destinations and set them under a group dial number. You can then use a group dial number to send a document to all of the destinations within the group. You can set up to 199 group dial numbers using the destination’s existing speed dial numbers. You can set up Phone Book with the fax numbers you use most frequently.
Using group dial numbers When you are prompted to enter a destination number while sending a fax, enter the group dial number at which you stored the number you want. • For a one-digit (0-9) group dial number, press and hold the corresponding digit button on the number keypad. • For a two- or three-digit group dial number, press the first digit button(s) and then hold down the last digit button. Searching Phone Book for an entry You can search for a number in memory.
11 Ordering supplies and accessories This chapter provides information on purchasing toner cartridge available for your machine. Toner cartridges When the toner runs out, you can order the following types of toner cartridge for your machine: Type Average Yield1 Part number High yield 3,000 Standard pages SCX-D4725A 1. Declared yield value in accordance with ISO/IEC 19752.
12 Maintenance Printing a report This chapter provides information for maintaining your machine and the toner cartridge. 1 Press Menu until Reports appears on the top line of the display. 2 Press the Scroll buttons until the report or list you want to print appears and press Enter. This chapter includes: The selected information prints out.
Options Description Phone Book Cautions • To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Cover it with a piece of paper, if necessary. • Do not touch the green surface underside of the toner cartridge. Use the handle on the cartridge to avoid touching this area. Clears all of the fax numbers stored in memory. 4 Repeat step 3 to clear another item. 5 Press Stop/Clear to return to Standby mode. 3 Pull the manual tray out.
5 Locate the long strip of glass (LSU) inside the top of the cartridge compartment, and gently swab the glass to see if dirt turns the white cotton black. 3 Wipe the surface of the scanner glass and ADF glass until it is clean and dry. 1 3 2 4 6 Push the manual tray back into the machine. 1 2 3 4 7 Reinsert the toner cartridge and close the front cover. 8 Plug in the power cord and turn the machine on.
Redistributing toner 4 When the toner cartridge is near the end of its life: Hold the toner cartridge by the handle and slowly insert the cartridge into the opening in the machine. Tabs on the sides of the cartridge and corresponding grooves within the machine will guide the cartridge into the correct position until it locks into place completely. • White streaks or light printing occurs. • Toner Low appears on the display.
Cleaning the drum Note You can set the machine to disregard the Toner Empty Replace Toner message and to continue printing. See page 12.6. 1 Open the front cover. 2 Pull the toner cartridge out. If there are streaks or spots on your print, the OPC drum of the toner cartridge may require cleaning. 1 Before starting the cleaning procedure, make sure that paper is loaded in the machine. 2 Press Menu until Maintenance appears on the top line of the display. 3 Press Enter when Clean Drum appears.
Printing continuously when the Toner Empty Replace Toner message appears Maintenance parts To avoid print quality and paper feed problems resulting from worn parts and to maintain your printer in top working condition, the following items will need to be replaced at the specified number of pages or when the life span of each item has expired. When the toner cartridge is nearly empty, the machine shows the Toner Empty Replace Toner message and stops printing.
Managing your machine from the website (SCX-4725FN only) If you have connected your machine to a network and set up TCP/IP network parameters correctly, you can manage the machine via Samsung’s SyncThru™ Web Service, an embedded web server. Use SyncThru™ Web Service to: • View the machine’s device information and check its current status. • Change TCP/IP parameters and set up other network parameters. • Change the printer properties.
13 Troubleshooting Note If you do not see the paper in this area, refer to Exit Misfeed. See the next section. This chapter gives helpful information for what to do if you encounter an error. 4 This chapter includes: Close the ADF cover. Then load the removed pages, if any, back into the ADF.
In the fuser area or around the toner cartridge Caution To avoid tearing the paper, pull out the jammed paper gently and slowly. Follow the instructions in the following sections to clear the jam. Note The fuser area is hot. Take care when removing paper from the machine. In the tray 1 Open the front cover and pull the toner cartridge out. 1 2 If necessary, pull the manual tray out. 3 Remove the jammed paper by gently pulling it straight out.
3 Open the rear cover. Tips for avoiding paper jams By selecting the correct media types, most paper jams can be avoided. When a paper jam occurs, follow the steps outlined on page 13.1. • Follow the procedures on page 5.5. Ensure that the adjustable guides are positioned correctly. • Do not overload the tray. • Do not remove paper from the tray while your machine is printing. • Flex, fan, and straighten paper before loading. • Do not use creased, damp, or highly curled paper.
Message [Low Heat Error] Meaning Suggested solutions Message Meaning Suggested solutions Your machine’s memory has become full while trying to store an original into memory. To cancel the fax job, press 1 to select Yes. If you want to send those pages that have been successfully stored, press 2 to select No. You should send the remaining pages later, when memory is available. Document Jam The loaded original has jammed in the ADF. Clear the jam. See page 13.1.
Message Meaning Suggested solutions Message Meaning Suggested solutions Power has turned off then on and the machine’s memory has not been back up. The job which you were trying to do before the power failure must be completely re-done. The machine is waiting for a specified time interval to redial a previously busy station. You can press Enter to immediately redial, or Stop/Clear to cancel the redial operation. Scanner locked The scanner module is locked.
Condition Paper does not feed into the machine. The paper keeps jamming. Suggested solutions Printing problems • Remove any obstructions from inside the machine. • Paper has not been loaded correctly. Remove paper from the tray and reload it correctly. • There is too much paper in the tray. Remove excess paper from the tray. • The paper is too thick. Use only paper that meets the specifications required by the machine. See page 5.7.
Condition Possible cause Suggested solutions Condition Possible cause The machine prints, but the text is wrong, garbled, or incomplete. The printer cable is loose or defective. Disconnect the printer cable and reconnect. Try a print job that you have already printed successfully. If possible, attach the cable and the machine to another computer and try a print job that you know works. Finally, try a new printer cable. The wrong printer driver was selected.
Printing quality problems Condition If the inside of the machine is dirty or paper has been loaded improperly, you may notice a reduction in print quality. See the table below to clear the problem. Condition Light or faded print Vertical lines AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc Dropouts AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc If black vertical streaks appear on the page: • The drum inside the toner cartridge has probably been scratched. Remove the toner cartridge and install a new one. See page 12.4.
Condition Suggested solutions Condition Background scatter Background scatter results from bits of toner randomly distributed on the printed page. • The paper may be too damp. Try printing with a different batch of papers. Do not open packages of paper until necessary so that the paper does not absorb too much moisture. • If background scatter occurs on an envelope, change the printing layout to avoid printing over areas that have overlapping seams on the reverse side.
Condition Horizontal stripes AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc Curl Suggested solutions If horizontally aligned black streaks or smears appear: • The toner cartridge may be installed improperly. Remove the cartridge and reinsert it. • The toner cartridge may be defective. Remove the toner cartridge and install a new one. See page 12.4. • If the problem persists, the machine may require repair. Contact a service representative.
Scanning problems Condition The scanner does not work. The unit scans very slowly. Fax problems Suggested solutions Condition • Make sure that you place the original to be scanned face down on the scanner glass, or face up in the ADF. • There may not be enough available memory to hold the document you want to scan. Try the Prescan function to see if that works. Try lowering the scan resolution rate. • Check that the USB cable is connected properly. • Make sure that the USB cable is not defective.
Condition Suggested solutions Faxes do not store in memory. There may not be enough memory space to store the fax. If the display shows the Memory Full message, delete from memory any faxes you no longer need and then try again to store the fax. Blank areas appear at the bottom of each page or on other pages, with a small strip of text at the top. Common PostScript problems (SCX-4725FN only) The following situations are PS language specific and may occur when several printer languages are being used.
Common Linux problems Problem Possible cause and solutions The machine does not print. • Check if the printer driver is installed in your system. Open Unified Driver configurator and switch to the Printers tab in Printers configuration window to look at the list of available printers. Make sure that your machine is displayed on the list. If not, please, invoke Add new printer wizard to set up your device. • Check if the printer has started.
Problem Possible cause and solutions The machine does not scan. • Check if a document is loaded into the machine. • Check if your machine is connected to the computer. Make sure if it is connected properly if an I/O error is reported while scanning. • Check if the port is not busy. Since functional components of MFP (printer and scanner) share the same I/O interface (port), the situation of simultaneous access of different “consumer” application to the same port is possible.
14 Specifications Item This chapter includes: • General specifications • Printer specifications • Scanner and copier specifications • Facsimile specifications 11.2 Kg Package weight Paper: 1.3 Kg, Plastic: 0.5 Kg Duty cycle Monthly print: Up to 10,000 pages Printer specifications Description ADF Up to 30 sheets (75 g/m2) ADF document size Width: 142 to 216 mm Item Length: 148 to 356 mm Paper input capacity Weight (including consumables) 1. Sound Pressure Level, ISO 7779 2.
Scanner and copier specifications Item Facsimile specifications Description Item Description Compatibility TWAIN standard/WIA standard Compatibility ITU-T Group 3 Scanning method ADF and Flat-bed Color CIS (Contact Image Sensor) module Applicable line Public Switched Telephone Network (PSTN) or behind PABX Resolution Optical: 600 x 600 dpi (mono and color) Enhanced: 4,800 x 4,800 dpi Data coding MH/MR/MMR/JBIG/JPEG/ECM (Error Correction Mode) Effective scanning length Scanner glass: 297 mm
INDEX Numerics D J 2/4-up, special copy 6.3 date and time, set 2.2 delayed fax 9.6 display language, change 2.2 DRPD (Distinctive Ring Pattern Detection) mode, receiving mode 9.4 drum, clean automatically 12.5 manually 12.5 jam, clear document 13.1 paper 13.1 A accessories, order information 11.1 ADF 1.2 ADF rubber pad, replace 12.6 ADF, load 5.1 alarm sound 2.3 Ans/Fax mode, receiving mode 9.4 auto fit, special copy 6.3 broadcast faxes 9.6 C characters, enter 2.3 cleaning drum 12.5 inside 12.
O originals jam, clear 13.1 loading 5.1 output location 5.7 output tray 5.7 P paper guidelines 5.4 paper jam, clear fuser area or around toner cartridge 13.2 manual tray 13.2 paper exit area 13.2 tray 13.2 paper load manual tray 5.6 tray 5.5 paper size setting 5.7 specifications 5.3 paper type setting 5.7 specifications 5.3 Phone Book group dial numbers 10.3 speed dial numbers 10.3 poster, special copy 6.4 PostScript problems 13.12 power save mode 2.4 print quality problems, solve 13.
Samsung Printer Software section
SOFTWARE SECTION CONTENTS Chapter 1: INSTALLING PRINTER SOFTWARE IN WINDOWS Installing Printer Software ........................................................................................................ 4 Installing Software for Local Printing ................................................................................. 4 Installing Software for Network Printing ............................................................................. 7 Reinstalling Printer Software ......................
Editing a Watermark ..................................................................................................... 20 Deleting a Watermark ................................................................................................... 20 Using Overlays ...................................................................................................................... 21 What is an Overlay? ......................................................................................................
Chapter 8: USING YOUR PRINTER IN LINUX Getting Started ..................................................................................................................... 29 Installing the Unified Linux Driver ............................................................................................ 29 Installing the Unified Linux Driver ................................................................................... 29 Uninstalling the Unified Linux Driver .......................................
1 Typical Installation Installing Printer Software in Windows This is recommended for most users. All components necessary for printer operations will be installed. This chapter includes: • Installing Printer Software 1 Make sure that the printer is connected to your computer and powered on. 2 Insert the supplied CD-ROM into your CD-ROM drive. The CD-ROM should automatically run, and an installation window appears.
7 NOTE: If your printer is not already connected to the computer, the following window will appear. To register yourself as a user of Samsung Printers in order to receive information from Samsung, select the checkbox and click Finish. You are now sent to the Samsung web site. Otherwise, just click Finish. • After connecting the printer, click Next. • If you don’t want to connect the printer at this time, click Next, and No on the following screen.
3 Click Next. • If necessary, select a language from the drop-down list. NOTE: If your printer is not already connected to the computer, the following window will appear. • View User’s Guide: Allows you to view the User’s Guide. If your computer doesn’t have Adobe Acrobat, click on this option and it will automatically install Adobe Acrobat Reader for you. 4 5 Select Custom installation. Click Next. • After connecting the printer, click Next.
7 After the installation is finished, a window asking you to print a test page appears. If you choose to print a test page, select the checkbox and click Next. If the installation window does not appear, click Start and then Run. Type X:\Setup.exe, replacing “X” with the letter which represents your drive and click OK. Otherwise, just click Next and skip to step 9. 8 If the test page prints out correctly, click Yes. If not, click No to reprint it.
5 The list of printers available on the network appears. Select the printer you want to install from the list and then click Next. NOTE: After setup is complete, if your printer driver doesn’t work properly, reinstall the printer driver. See “Reinstalling Printer Software” on page 10. Custom Installation You can choose individual components to install and set a specific IP address. 1 Make sure that the printer is connected to your network and powered on.
4 Select Custom installation. Click Next. TIP: If you want to set a specific IP address on a specific network printer, click the Set IP Address button. The Set IP Address window appears. Do as follows: 5 The list of printers available on the network appears. Select the printer you want to install from the list and then click Next. a. Select a printer to be set with a specific IP address from the list. b.
7 After the installation is finished, a window appears asking you to print a test page and to register yourself as a user of Samsung Printers in order to receive information from Samsung. If you so desire, select the corresponding checkbox(es) and click Finish. Reinstalling Printer Software You can reinstall the software if installation fails. 1 Start Windows. Otherwise, just click Finish. 2 3 4 From the Start menu select Programs or All Programs → your printer driver name → Maintenance.
Removing Printer Software NOTE: If your printer is not already connected to the computer, the following window will appear. 1 2 3 4 5 6 Start Windows. From the Start menu select Programs or All Programs → your printer driver name → Maintenance. Select Remove and click Next. You will see a component list so that you can remove any item individually. Select the components you want to remove and then click Next. When your computer asks you to confirm your selection, click Yes.
2 1 2 Basic Printing This chapter explains the printing options and common printing tasks in Windows. Open the document you want to print. Select Print from the File menu. The Print window is displayed. It may look slightly different depending on your application. The basic print settings are selected within the Print window. These settings include the number of copies and print range.
Layout Tab Printer Settings The Layout tab provides options to adjust how the document appears on the printed page. The Layout Options includes Multiple Pages per Side and Poster Printing. See “Printing a Document” on page 12 for more information on accessing printer properties. You can use the printer properties window, which allows you to access all of the printer options you need when using your printer.
Paper Tab 3 Source Make sure that Source is set to the corresponding paper tray. Use Manual Feeder when printing on special materials like envelopes and transparencies. You have to load one sheet at a time into the Manual Tray or Multi-Purpose Tray. If the paper source is set to Auto Selection, the printer automatically picks up print material in the following tray order: Manual Tray or Multi-Purpose Tray, Tray n.
Graphics Tab Advanced Options Use the following Graphic options to adjust the print quality for your specific printing needs. See “Printing a Document” on page 12 for more information on accessing printer properties. You can set advanced settings by clicking the Advanced Options button. • TrueType Options: This option determines what the driver tells the printer about how to image the text in your document. Select the appropriate setting according to the status of your document.
Extras Tab About Tab You can select output options for your document. See “Printing a Document” on page 12 for more information about accessing the printer properties. Use the About tab to display the copyright notice and the version number of the driver. If you have an Internet browser, you can connect to the Internet by clicking on the web site icon. See “Printing a Document” on page 12 for more information about accessing printer properties.
Using a Favorite Setting The Favorites option, which is visible on each properties tab, allows you to save the current properties settings for future use. To save a Favorites item: 1 2 Change the settings as needed on each tab. 3 Click Save. Enter a name for the item in the Favorites input box. When you save Favorites, all current driver settings are saved. To use a saved setting, select the item from the Favorites drop down list.
3 Advanced Printing Printing Multiple Pages on One Sheet of Paper (N-Up Printing) This chapter explains printing options and advanced printing tasks. 1 2 3 4 NOTE: • Your printer driver Properties window that appears in this User’s Guide may differ depending on the printer in use. However the composition of the printer properties window is similar. • If you need to know the exact name of your printer, you can check the supplied CD-ROM.
Printing Posters Printing a Reduced or Enlarged Document This feature allows you to print a single-page document onto 4, 9, or 16 sheets of paper, for the purpose of pasting the sheets together to form one poster-size document. 1 2 3 You can change the size of a page’s content to appear larger or smaller on the printed page. To change the print settings from your software application, access printer properties. See “Printing a Document” on page 12.
Editing a Watermark Using Watermarks 1 The Watermark option allows you to print text over an existing document. For example, you may want to have large gray letters reading “DRAFT” or “CONFIDENTIAL” printed diagonally across the first page or all pages of a document. 2 There are several predefined watermarks that come with the printer, and they can be modified, or you can add new ones to the list.
Using a Page Overlay Using Overlays After an overlay has been created, it is ready to be printed with your document. To print an overlay with a document: 1 2 What is an Overlay? Dear ABC Regards WORLD BEST An overlay is text and/or images stored in the computer hard disk drive (HDD) as a special file format that can be printed on any document. Overlays are often used to take the place of preprinted forms and letterhead paper.
4 Advanced Using Windows PostScript Driver (SCX-4725FN only) You can use advanced settings by clicking the Advanced button. If you want to use the PostScript driver provided with your system CD-ROM to print a document. PPDs, in combination with the PostScript driver, access printer features and allow the computer to communicate with the printer. An installation program for the PPDs is provided on the supplied software CD-ROM.
5 Sharing the Printer Locally Setting Up a Host Computer 1 2 3 4 5 6 You can connect the printer directly to a selected computer, which is called “host computer,” on the network. The following procedure is for Windows XP. For other Windows OS, refer to the corresponding Windows User's Guide or online help. NOTES: • Check the Operating System(s) that are compatible with your printer. Please refer to the OS Compatibility section of Printer Specifications in your Printer User’s Guide.
6 The Smart Panel program displays the current status of the printer, various information, lets you change settings and the level of toner remaining in the toner cartridge(s). Using Smart Panel Smart Panel is a program that monitors and informs you of the status of the printer, and allows you to customize the printer’s settings. Smart Panel is installed automatically when you install the printer software. 2 3 NOTES: 1 • To use the this program, you need: - Windows 98 or higher (Windows NT 4.
Using Printer Settings Utility Changing the Smart Panel Program Settings Using the Printer Settings Utility, you can configure and check print settings. 1 2 3 Right-click the Smart Panel icon on the Windows task bar and select Options. Right-click the Smart Panel icon on the Windows task bar and select Printer Setting. Change the settings. The following window opens. To send the changes to the printer, click the Apply(or Send) button.
7 Scanning Scanning Using Samsung SmarThru Scanning with your machine lets you turn pictures and text into digital files on your computer. Then you can fax or e-mail the files, display them on your web site or use them to create projects that you can print using Samsung SmarThru software or the WIA driver. Samsung SmarThru is the accompanying software for your machine.
Using Samsung SmarThru 4 Follow these steps to start scanning using the SmarThru: 1 Make sure that your machine and computer are turned on and properly connected to each other. 2 Place your photograph or page on the document glass or ADF. 3 Once you have installed Samsung SmarThru, you will see the SmarThru 4 icon on your desktop. Double-click the SmarThru 4 icon. Click Scan To. The Scan To menu bar appears on the SmarThru 4 window. Scan To menu bar Adjust the scan settings.
•Settings Scanning Using the WIA Driver Customizing settings of Scan To basic functions. Allows you to customize settings for Application, E-mail, OCR, and Web functions. 5 Click the service icon according to your job. 6 SmarThru 4 opens for the selected service. Adjust the scan settings. 7 To start scanning, click Scan. Your machine also supports the Windows Image Acquisition (WIA) driver for scanning images.
8 Using Your Printer in Linux Installing the Unified Linux Driver You can use your machine in a Linux environment. Installing the Unified Linux Driver 1 This chapter includes: • Getting Started 2 • Installing the Unified Linux Driver Make sure that you connect your machine to your computer. Turn both the computer and the machine on. When the Administrator Login window appears, type in root in the Login field and enter the system password.
5 Uninstalling the Unified Linux Driver When the installation is complete, click Finish. 1 When the Administrator Login window appears, type in root in the Login field and enter the system password. NOTE: You must log in as a super user (root) to install the printer software. If you are not a super user, ask your system administrator. 2 Insert the printer software CD-ROM. The CD-ROM will automatically run. If the CD-ROM does not automatically run, click the icon at the bottom of the desktop.
Printers Configuration Using the Unified Driver Configurator Printers configuration has the two tabs: Printers and Classes. Printers Tab You can see the current system’s printer configuration by clicking on the printer icon button on the left side of the Unified Driver Configurator window. Unified Linux Driver Configurator is a tool primarily intended for configuring Printer or MFP devices.
Classes Tab Ports Configuration The Classes tab shows a list of available printer classes. In this window, you can view the list of available ports, check the status of each port and release a port that is stalled in busy state when its owner is terminated for any reason. Shows all of the printer classes. Switches to ports configuration. Shows the status of the class and the number of printers in the class. Shows all of the available ports.
Configuring Printer Properties Printing a Document Using the properties window provided by the Printers configuration, you can change the various properties for your machine as a printer. 1 Open the Unified Driver Configurator. Printing from Applications 2 3 There are a lot of Linux applications that you are allowed to print from using Common UNIX Printing System (CUPS). You can print on your machine from any such application. 1 From the application you are using, select Print from the File menu.
5 6 7 The following four tabs display at the top of the window. • General - allows you to change the paper size, the paper type, and the orientation of the documents, enables the duplex feature, adds start and end banners, and changes the number of pages per sheet. • Text - allows you to specify the page margins and set the text options, such as spacing or columns. • Graphics - allows you to set image options that are used when printing images/files, such as color options, image size, or image position.
10 When you are finished, click Save on the toolbar. 11 Select the file directory where you want to save the image The document is scanned and the image preview appears in the Preview Pane. and enter the file name. 12 Click Save. Adding Job Type Settings You can save your scan option settings to retrieve for a later scanning. To save a new Job Type setting: 1 Change the options from the Scanner Properties window. Drag the pointer to set the image area to be scanned. 2 3 4 Click Save As.
You can use the following tools to edit the image: Tools Function Saves the image. Cancels your last action. Restores the action you canceled. Allows you to scroll through the image. Crops the selected image area. Zooms the image out. Zooms the image in. Allows you to scale the image size; you can enter the size manually, or set the rate to scale proportionally, vertically, or horizontally. Allows you to rotate the image; you can select the number of degrees from the dropdown list.
9 Using Your Printer with a Macintosh (SCX-4725FN only) Installing Software for Macintosh The PostScript driver CD-ROM that came with your machine provides you with the PPD file to use the PS driver, Apple LaserWriter driver, for printing on a Macintosh computer. Your machine supports Macintosh systems with a built-in USB interface or a 10/100 Base-TX network interface card. When you print a file from a Macintosh computer, you can use the PostScript driver by installing the PPD file.
Install the Scan driver 1 2 3 Setting Up the Printer Make sure that you connect your printer to the computer. Turn on your computer and printer. Insert the CD-ROM which came with your printer into the CD-ROM drive. Double-click CD-ROM icon that appears on your Macintosh desktop. Double-click the MAC_Installer folder. Set up for your printer will be different depending on which cable you use to connect the printer to your computer—the network cable or the USB cable.
Changing Printer Settings Printing You can use advanced printing features when using your printer. From your Macintosh application, select Print from the File menu. The printer name which appears in the printer properties window may differ depending on the printer in use. Except for the name, the composition of the printer properties window is similar. NOTES: • The Macintosh printer’s properties window that appears in this User’s Guide may differ depending on the printer in use.
Printing Multiple Pages on One Sheet of Paper Printer Features Setting The Printer Features tab provides options for selecting the paper type and adjusting print quality. You can print more than one page on a single sheet of paper. This feature provides a cost-effective way to print draft pages. Select Printer Features from the Presets drop-down list to access the following features: 1 2 From your Macintosh application, select Print from the File menu. Select Layout. ▲ Mac OS 10.
Scanning If you want to scan documents using other software, you will need to use TWAIN-compliant software, such as Adobe PhotoDeluxe or Adobe Photoshop. The first time you scan with your machine, select it as your TWAIN source in the application you use. The basic scanning process involves a number of steps: • Place your photograph or page on the document glass or ADF. • Open an application, such as PhotoDeluxe or Photoshop. • Open the TWAIN window and set the scan options.
SOFTWARE SECTION INDEX A advanced printing, use 18 C canceling scan 28 Windows 13 Linux driver, install 29 printer properties 33 printing 33 scanning 34 M Extras properties, set 16 Macintosh driver install 37 uninstall 37 printing 39 scanning 41 setting up the printer 38 MFP driver, install Linux 29 F N favorites settings, use 17 n-up printing Macintosh 40 Windows 18 D document, print Macintosh 39 Windows 12 E G Graphics properties, set 15 H help, use 17, 22 I install printer driver Macintosh
Linux 34 SmarThru 26 TWAIN 28 WIA driver 28 scanning from Macintosh 41 setting darkness 15 favorites 17 image mode 15 resolution Macintosh 40 Windows 15 toner save 15 true-type option 15 software install Macintosh 37 Windows 4 reinstall Windows 10 system requirements Macintosh 37 uninstall Macintosh 37 Windows 11 status monitor, use 24 T toner save, set 15 TWAIN, scan 28 U uninstall, software Macintosh 37 Windows 11 uninstalling MFP driver Linux 30 W watermark create 20 delete 20 edit 20 print 20 WIA, sc
www.samsungprinter.com Rev. 2.
