PORTABLE CELLULAR TELEPHONE SCH-620 SERVICE PORTABLE CELLULAR TELEPHONE Manual CONTENTS 1. General Introduction 2. Specification 3. Installation 4. NAM Programming 5. Product Support Tools OK/ MENU CLR END/ 2 3 DEF SEND 1. ´ 4 GHI 7 PQRS ABC 5 JKL 6 MNO 8 9 WXYZ TUV 6. Troubleshooting 7. Exploded view and its Part List 0 OPER 8. Electrical Parts List 9. Block diagram 10. PCB diagrams 11.
1. General Description The SCH-620 cellular phone functions as both analog cellular phone working in AMPS (Advanced Mobile Phone Service) mode and digital cellular phone working in CDMA (Code Division Multiple Access) mode. CDMA type digital mode applies DSSS (Direct Sequential Spread spectrum) mode which first came to be used in the military.
2. Specification 2-1 General Frequency Range Transmitter Receiver Digital Mode : 824 ~ 849 MHz : 869 ~ 894 MHz Analog Mode 824 ~ 849 MHz 869 ~ 894 MHz Channel Spacing : 1.23 MHz 30 kHz Number of Channels : 20 FA 832 CHs Duplex Spacing : 45 MHz 45 MHz Frequency Stability : ±2.5 ppm (-30˚C ~ +60˚C, -4˚F ~ +140˚F) Operating Temperature : -30˚C~+60˚C (-4˚F ~ +140˚F) Operating Voltage HHP : 3.6V DC (±10%) Hands-free : 13.
Specification 2-2 Digital Mode Waveform Quality 0.944 or more Time Reference ±1uS or less Rx Sensitivity and Dynamic Range Tx Output Power -104 dBm, FER=0.5 % or less -25 dBm, FER=0.5 % or less 280 mW (24.5 dBm) Tx Frequency Deviation ±300 Hz or less Occupied Band Width 1.32 MHz Tx Conducted Spurious Emission Minimum Tx Power Control Open Loop Power Control Standby Output Power 900 kHz : -42 dBc / 30 kHz below 1.98 MHz: -54 dBc / 30 kHz below below -50 dBm -25 dBm: -57.0 dBm ~ -38.
Specification 2-3 ANALOG MODE TRANSMITTER 0.6W (+2/-4dB) RF output power Carrier ON/OFF conditions “ON” Condition “OFF” Condition Compressor Compression Rate Attack Time Recovery Time Reference Input within ±3dB of specification output (in 2mS) below-60dBm (in 2mS) 2:1 3mS 13.5mS Input level for producing a nominal ±2.9KHz peak freqency deviation of transmitted carrier 6dB/OCT within 0.
Specification RECEIVER -6dB / OCT within 0.3 ~3KHz De-Emphasis Expander Expander Rate Attack Time Recovery Time Reference Input 1:2 within 3mS within 13.5mS output level to a 1000Hz tone from a carrier within ±2.
Specification 2-4 CDMA Debug Display Information (menu 8) IN IDLE MODE 1 2 3 Sxxxx 4 SIx T-xx x Dxxx Pxxx -xx 6 CHxxx 8 7 5 IN CONVERSATION MODE 9 10 TEx T-xx Pxxx REx 11 xx Dxxx x -xx 3 CHxxxx 1 : Sxxxxx : SID (System ldentification) toggle Nxxxxx : NID (Network Identification) toggle 2 : SIx : Slot cycle index (lowest between the system and the phone will be used) 3 : Handset Status : 0 - Acquisition 1 - Synchronization 2 - Paging (Idle) 3 - Traffic Initialization 4 - Traffic Mode 5
3. Installation 3-1 Installing a Battery Pack 1. To attach the battery pack after charging, align it with the phone about 1cm (1/2 inch away from its place so that the two arrows on the phone are seen, the battery charge contacts pointing downward. 2. Slide the battery pack upwards until it clicks firmly into position. The phone is now ready to be turned on. 3. To remove the battery pack, release it by pressing the button on the rear of the phone. 4.
Installation 3-2 For Desk Top Use 1. Choose a proper location to install the charger for Desk Top use. 2. Plug the power cord of the charger into an appropriate wall socket. When the power is connected correctly, the lamps turn on briefly. 3. To charge the battery pack, insert the battery pack into the rear slot of the charger. The lamp marked BAT on the front panel of the charger lights up red. 4.
Installation 3-3 For Mobile Mount 3-3-1 Cradle 1. Choose a location where it is easy to reach and does not interfere with the driver’s safe operation of the car. 2. Separate the two halves of the clamshell by removing the two large slotted screws. See the figure 3-2. 3. Drill holes and mount the lower half of the clamshell by using the screws. 4. Place the cradle onto the remaining half of the clamshell and assemble them by using the screws. 5. Reassemble the two halves of the clamshell together.
Installation 3-3-3 Hands-Free Microphone 1. It is recommended to install the microphone where it is 30-45 cm (12-18inch away from the driver. Choose the location where is least susceptible to interference caused by external noise sources, ie, adjacent windows, radio speakers, etc. Normal place is the sun visor. 2. Once the microphone has been correctly positioned, connect the microphone wire to the MIC jack on the hands-free box.
Installation 3-3-4 Cables 1. Connect the cradle and the hands-free box with the data cable. See the figure 3-4. 2. Connect the antenna cable to the RF jack of the cradle. 3. Connect the power cable as follows: Connect the red wire to the battery (+) terminal, black wire to the vehicle chassis. Then connect the battery (-) terminal to the vehicle chassis. Connect the yellow wire to the switched side of the ignition switch, and then connect the white to the stereo mute wire from your vehicle stereo. 4.
4. NAM Programming NAM features can be programmed as follows: Notes: - If you enter the NAM program mode, each item shows the currenly stored data. Go to the next item by pressing OK. - You can modify the data by entering a new data. - If you enter a wrong digit, press CLR to delete the last digit. Press and hold CLR to delete all digits. - To scroll items backwards or forwards, press the VOLUME button on the left side of the phone.
NAM Programming LCD Display Key in Pref NAM2... Digital pref OK Function -Preferred system selection for NAM2 changes the system. -stores it. 4-2 Setting Up NAM1 LCD Display Key in Function NAM Program 1:General 2:Setup NAM1 3:Setup NAM2 2 Choose ‘Setup NAM1.’ Setup NAM1 1:Phone # 2.FM 2:CDMA 1 Choose ‘Phone #’ phone number Phone number currently used. - to change, enter new one. - store it. Phone # 1234567890 OK Mobile ID # 3003003000 Setup NAM1 1:Phone # 2.
NAM Programming LCD Display FM Acq SID3 0 FM Acq SID4 0 FM Acq SID5 0 FM Acq SID6 0 FM LockSID 1 0 FM LockSID 2 0 FM LockSID 3 0 FM LockSID 4 0 FM LockSID 5 0 FM LockSID 6 0 Auto Reg Yes Key in Function ID number OK Acquisition system ID 3, Current status is displayed. - to change, enter new one. - store it. ID number OK Acquisition system ID 4, Current status is displayed. - to change, enter new one. - store it. ID number OK Acquisition system ID 5, Current status is displayed.
NAM Programming LCD Display FM ACCOLC 0 Setup NAM1 1:Phone # 2.FM 2:CDMA Key in * or # OK Current Access Overload Class. - change the status. - store it. 3 - Choose ‘CDMA’ number OK IMSI Moble Country Code, current code is displayed. - to change, enter new one. - stores it. number OK IMSI Mobile Network Code, current code is displayed. - to change, enter new one. - stores it. * or # OK Preferred system selection, current system is displayed. - changes the system. - stores it.
NAM Programming LCD Display CD Acq SID 3 0 CD Acq SID 4 0 CD Acq SID 5 0 CD Acq SID 6 0 CD lockSID 1 0 CD lockSID 2 0 CD lockSID 3 0 CD lockSID 4 0 CD lockSID 5 0 CD lockSID 6 0 CDMA HomeSID Yes CDMA fSID Yes CDMA fNID Yes Key in Function ID number OK 3rd Acquisition system ID, current status is displayed. - to change, enter new one. - stores it. ID number OK 4th Acquisition system ID, current status is displayed. - to change, enter new one. - stores it.
NAM Programming LCD Display SID #1 2222 NID #1 1 SID #2 2222 NID #2 2 SID #3 2222 NID #3 3 SID #4 2222 NID #4 3 Key in Function number OK first SID written in the list, current status is displayed. - to change, enter new one. - stores it. number OK first NID written in the list, current status is displayed. - to change, enter new one. - stores it. number OK 2nd SID written in the list, current status is displayed. - to change, enter new one. - stores it.
NAM Programming Austria Only 1. Setting Up NAM1 LCD Display NAM Program 1:Setup NAM1 2:Setup NAM2 NAM1 Phone # 1234567890 NAM1 Directory # 1234567890 NAM1 Activate PRL Yes NAM1 Anlg HomeSID **** NAM1 Dgti HomeSID **** NAM1 More Prog ? Yes Key in Function MEMU40654321 -select NAM programming 1 -choose ‘Setup NAM1’ Phone number OK -Phone number. -to change, enter new one. -store it. Directory number OK -Directory number. -to change, enter new one. -store it.
NAM Programming 3. Setting up General LCD Display NAM Program 1:General 2:Setup NAM1 3:Setup NAM2 General ESN F1000000 General CAI version Key in Function 1 -Choose ‘GENERAL’. Volume -Electronic Serial Number of the phone is displayed. Volume -Common Air interface version is displayed. * or # OK -Vocoder data rate. Volume -Station Class Mark displays the power class, transmission, slotted class, dual mode.
NAM Programming 4. Setting up NAM1 LCD Display NAM Program 1:General 2:Setup NAM1 3:Setup NAM2 Key in Function 2 -Choose ‘Setup NAM1’. *** 3-digit number OK IMSI Moble Country Code, current code is displayed. -to change, enter new one. -stores it. ** 2-digit number OK IMSI Mobile Network Code, current code is displayed. -to change, enter new one. -stores it. Phone number OK -Phone number. -to change, enter new one. -stores it. Directory number OK -Directory number. -to change, enter new one.
NAM Programming LCD Display Key in NAM1 Digital CDMA fNID Yes * or # OK CDMA foreign NID, current status is displayed -change the system. -store it. class number OK CDMA Access Overload Class, current status is diplayed. -to change, enter new one. -store it. Phone number OK -Phone number. -to change, enter new one. -store it. SID number OK Analog Home System ID, current status displayed -to change, enter new one. -store it. * or # OK Analog Registration, current status is displayed.
5. Product Support Tools 5-1 General IMPORTANT INFORMATION Purpose The Product Support Tool (PST) offers you the ability to interface with the SAMSUNG CDMA telephone using a PC. With this tool you can program the phones network system requirements and functionality, swap phone data, and download software upgrades. This document supports UniPST version 1.xx. NOTE: This software must be executed in the Windows95/98 mode. EQUIPMENT REQUIRED Make sure you have the following equipment setup: 1.
Product Support Tools 5-2. PST (Product Support Tool) 5-2-1 Getting Started MAIN MENU SCREEN 1. At the Windows95/98, Double Click “UniPst.exe”. 2. The Main Menu Screen will be displayed. The Main Menu Screen shows the basic tasks that are available. CAUTION: DO NOT attempt to program phone with a low battery. PST SETUP UniPst supports SAMSUNG CDMA portable telephone. You can select serial port COM1 or COM2.
Product Support Tools Save Data to File Click this icon to save the current parameters to a file. Once you enter a filename, Click button to write all current parameters to that file. This way the same information can be downloaded into multiple phones. Write to Phone Click this icon to write the selected parameter values to the phone. Writing the selected values to the phone may take up to a minute.
Product Support Tools 5-3 TEST PROCEDURE 5-3-1 Configuration of Test Spectrum Analyzer RF In HP8924C RF In/Out Audio Audio Out In Directional Coupler To A-Out Test Jig To A-In DC Power Supply (+3.93V) ❈ CAUTION : Because there is the loss (0.33V at Max Power) of the test jig and Data cable, you’d better input 3.93V to the DC Power Supply to use 3.
Product Support Tools 5-3-2 List of Equipment - DC Power Supply - Test Jig - Test Cable - CDMA Mobile Station Test Set - Spectrum Analyzer(include CDMA Test Mode) HP8924C, HP83236A, CMD-80, etc HP8596E TEST JIG DC POWER INPUT PORT CHANGE VOLTAGE LEVEL BY MODEL (3.8VDC) RED: + BLACK: GND AUDIO SELECT LEFT: AUDIO IN RIGHT: AUDIONOFF UP: AUTO POWER ON DOWN: NOT USE AUTO DB25 CONNECTOR CPMMECT TO DB25 CONNECTOR OF TEST CABLE A-IN - DC3.
Product Support Tools TEST CABLE CONNECTIONS 1 MHC 172 2 RF CABLE (1.4 dB Loss) 3 BNC CONNECTOR (RF) 4 PLUG CONNECT TO SCH-611 5 DATA CABLE 6 Dsub 25PIN CONNECTOR (DATA) Dsub 25 PIN CONNECTOR PIN DESCRIPTION (TEST CABLE 1, BACK SIDE) DATA DESCRIPTION Dsub CONN. PIN NO. DATA DESCRIPTION Dsub CONN. PIN NO.
Product Support Tools 5-4. CONVERSION TABLE OF FREQUENCY vs CHANNEL TYPE CHANNEL CONVERSION EQUATION REMARK TX 1 ≤ N≤ 799 F=0.03 ✕ N + 825.00 FREQUENCY 990 ≤N≤1023 F=0.03 ✕ (N-1023) + 825.00 N ; CH NUMBER RX 1 ≤N≤ 799 F=0.03 ✕ N + 870.00 F ; FREQUENCY FREQUENCY 990 ≤N≤1023 F=0.03 ✕ (N-1023) + 870.00 Change to Test Mode A. To change the phone’s state from Normal Mode to Test Mode, You should enter the following keys. “*759#813580“ B. The command “0 1” is Suspend. C.
Product Support Tools 5-5 TEST COMMAND TABLE Command No. Signal.
Product Support Tools Command No. Signal. Name Description 45 COMPANDOROFF turn off compandor 47 FM_AUD_GAIN FM audio gain 48 VIBRATOR_ON activate a vibrator 49 VIBRATOR_OFF inactivate a vibrator 50 BATT_TYPE Battery Type 51 BBA BBASIC supplier 52 HW_VERSION HW version hmk_96.12.
Product Support Tools Command No. Signal.
6. Troubleshooting 6-1 Logic Section 6-1-1 No Power Press END/ button U208 pin 1=3.6V? No Check the signal from the battery terminal to Q203 pin 4. No Check U210 and its neighboring circuits. No Check U210 and its neighboring circuits. No Check U206 and its neighboring circuits. Yes U210 pin 1 input =3.6V? Yes U210 pin 5 output =3.0V? Yes U206 pin 5 output =3.
Troubleshooting 6-1-2 Abnormal Initial Operation (Normal +3.0V voltage source) Press END/ button TCXO CLK applied to U406 pin 35? No Check TCXO output, R460 and C467. Replace if required. No Check U304 and its neighboring circuit. Replace if required. No Check U202, pin 2 Replace if required. No Check ‘H’ level input U304 pin 38. No Check the LED and its neighboring circuit. Replace if required. No Check the LCD pins and its neighboring circuit. Replace if required.
Troubleshooting 6-1-3 Abnormal Backlight Operation Press and button on the phone ‘H’ level output from U104 pin 7L? No Check U104 pin7L. Replace if required. No Check U209 and its neighboring circuits. Replace if required No Check Q206, L202 and its neighboring circuits.
Troubleshooting 6-1-4 Abnormal Key Data input Check initial status Scanning signals output from U104, pins 5C, 48, 5D, 4A, 6C, 5A, 6D? No Check U104 pins 5C, 48, 5D, 4A, 6C, 5A, 6D No Replace the keypad assembly Yes Check U104 pins 2A, 4C, and 3B Yes Check CON102-24.
Troubleshooting 6-1-5 Abnormal Key tone Abnormal Keytone CLK Waveform output from U204 pin 17? No Check U204 pin 17. Replace if required. No Check U204, pin 15. Replace if required. No Check Q201,Q202,R227,R220, and D206.Replace if required.
Troubleshooting 6-2 Transmitter Section Power Level : +10dBm DC Power Supply : 3.95V CH:363 Abormal transmitter section No Check Tx PLL OK? No Check U406 Tx IF level OK? SPAN 5MHz Tx VCO:270.76MHz IF:130.38MHz Yes CDMA: -15dBm Check U406 local Input level CDMA: -8dBm Yes Yes Check Tx Power level. OK? No Check U404 Out level. OK? CDMA: -12dBm Yes Check U306 Out level CDMA: +8.63dBm No SAMSUNG Proprietary-Contents may change without notice 6-6 969.
Troubleshooting 6-3 FM Receiver Section Power Level : -50dBm DC Power Supply : 3.95V CH:363 RX part No Check FM 12dB SINAD OK? Check LNA in/output OK? No Check Duplexer & LNA power Gain: +20dB Yes Yes Yes Check 1st local & mixer power OK? Check mixer in/output OK? Gain(FM): -8dB No Check PLL (U504) & VCO output local: -2.
Troubleshooting 6-4 CDMA Receiver Section Start CDMA mode Normal CDMA SVC & ROAM OK? No Check CDMA RX path Setup CDMA call.
Troubleshooting 6-5 Desk-Top Rapid Charger Plug_in Check LED state (RED>GRN>YEL) Check BAT-Contact. Check Voltage of C3, C2. (about 330V) Check F1, BD1, U1 Check Battery. Check component the secondary D30, D20, U22, U23, U24, U25, U26. Blank of Front. Check BAT-Contact. Check Battery. Check C30 Blank of Rear Check BAT-Contact. Check Battery. Check C40. Check Voltage of C41.(5V) Check U25. LED blink? (Yellow) Check Voltage of C22. (about 4.5V) Check U26. Check Voltage of C22. (about 4.
Troubleshooting 6-6 Hands-Free Kit 1 Start Ignition Check Phone Power ON/OFF Check Charger Circuit Auto Power ON Handset Hook ON/OFF Check Handset Mode Battery Check Hands Free Mode Charging current and voltage check according to battery type Full Charging check Charging LED Check In conversation mode, volume adijustment, mute on/off, calibration check Auto power off according to lgnition status Handsfree off with the phone powered off or removed SAMSUNG Proprietary-Contents may change with
7.
Exploded view and its Part List 7-2 Cellular phone Exploded List Location No. 1 Description SEC Code Remark FLIP COVER ASS’Y GH75-00428A LOGO BADGE GH68-20008A FRONT ASS’Y GH75-00426A 2-1 LCD WINDOW GH72-00180A SNA 2-2 LCD BOHO SPONGE GH74-00492A SNA 2-3 EAR JACK HOLDER GH72-00148A SNA 2-4 HINGE ASS’Y GH75-00046A SNA 2-5 ANTENNA CAP GH73-00094A 3 SIDE KEY ASS’Y GH75-00088A 4 KEY PAD GH72-00588A 5 KEY SHIELD CAN GH72-00554A 6 MIC.
Exploded view and its Part List 7-3 Desk-Top Rapid charger Exploded View 1 A TYPE 2 4 B SEC. CODE Remark A GH44-00063A Israel B GH44-00063B Hong Kong 6 3 5 7 8 No Description Q’TY 1 Case. upper 1 2 Hook-plate 2 9 3 SCREW 4 4 Battery housing 1 10 5 SCREW 1 6 Power cord 1 7 PCB 1 8 Case.
Exploded view and its Part List 7-4 Hands-free Kit 1 Exploded View 1 2 3 4 5 6 No 7 Description Q’TY 1 Case. upper 1 2 SCREW 3✕5Y 1 3 PCB 1 4 Case.
Exploded view and its Part List 7-5 Speaker Exploded View 6 7 4 9 3 8 5 2 1 No Description Q’TY 1 Case. Front 1 2 Speaker 1 3 Case. Rear 1 4 Bolt 2 5 HEX.
Exploded view and its Part List 7-6 Cradle Exploded View No Description Q’TY 1 Cover Top 1 2 Holder Socket 1 3 Spring Lock 2 4 Locker 1 5 Locker 1 6 Eject-A 1 7 Eject Spring 2 8 Frame 1 9 Eject-B 1 10 Screw 6 11 PCB 1 12 SCREW 4 13 Cover Bottom 1 14 Screw 2 15 Label 1 16 I/F coil cord 1 17 Data coil cord 1 1 2 4 3 6 5 7 9 8 7 10 11 12 16 13 14 15 17 SAMSUNG Proprietary-Contents may change without notice 7-6
8. Electrical Parts List 8-1 Main parts List Level Design LOC ITEMS DESCRIPTIONS 0 SEC CODE SCH-620B/TRJ 1 SCREW-MACHINE “BH,*,M2,L5,ZPC(BLK),SM20C,FDP” 6001-001148 1 SCREW-MACHINE “PH,+,M1.7,L5,ZPC(BLK),SWRCH18A,FP” 6001-001204 1 ANTENNA-SCH620 “SCH-620,824~895MHz,-,50ohm” GH42-00036A 1 “BATTERY-1000M,BLK,POT “3.6V,1000mAh,-,2CmA,4.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 ZD104 DIODE-ARRAY “DA221,20V,100mA,C2-3,EM3,TR” 0407-001006 2 ZD202 DIODE-ARRAY “DA221,20V,100mA,C2-3,EM3,TR” 0407-001006 2 ZD203 DIODE-ARRAY “DA221,20V,100mA,C2-3,EM3,TR” 0407-001006 2 D301 DIODE-PIN “BAR63-02W,50V,100mA,SCD-80,TP” 0409-001016 2 Q301 TR-SMALL SIGNAL “2SC4081,NPN,200mW,UMT,TP,180-3” 0501-000218 2 Q205 TR-SMALL SIGNAL “2SC4617,NPN,200mW,EM3,TP,120-5” 0501-000225 2 Q207 TR-SMALL SIGNAL “
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 U407 IC-SWITCH VOL. REG. “5205,SOT-23,5P,150MIL,PLASTIC,” 1203-001285 2 U210 IC-VOLTAGE REGULATOR “5219,SOT-23,5P,63MIL,PLASTIC,2.91/3.09V 1203-001720 2 U206 IC-RESET “3470,SOT23,5P,-,PLASTIC,0.99/1.01V,300mW 1203-001835 2 U204 IC-ENCODER/DECODER “ST5092TQFPTR,QFP,44P,-,PLASTIC” 1204-001375 2 U304 IC-IF CIRCUIT “IFR3000,TQFP,48P,-,PLASTIC,3.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 R568 R-CHIP “5.1Kohm,5%,1/16W,DA,TP,1005” 2007-000144 2 R452 R-CHIP “6.2Kohm,5%,1/16W,DA,TP,1005” 2007-000145 2 R143 R-CHIP “6.8Kohm,5%,1/16W,DA,TP,1005” 2007-000146 2 R239 R-CHIP “6.8Kohm,5%,1/16W,DA,TP,1005” 2007-000146 2 R454 R-CHIP “8.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 R152 R-CHIP “100Kohm,5%,1/16W,DA,TP,1005” 2007-000162 2 R170 R-CHIP “100Kohm,5%,1/16W,DA,TP,1005” 2007-000162 2 R173 R-CHIP “100Kohm,5%,1/16W,DA,TP,1005” 2007-000162 2 R208 R-CHIP “100Kohm,5%,1/16W,DA,TP,1005” 2007-000162 2 R235 R-CHIP “100Kohm,5%,1/16W,DA,TP,1005” 2007-000162 2 R245 R-CHIP “100Kohm,5%,1/16W,DA,TP,1005” 2007-000162 2 R247 R-CHIP “100Kohm,5%,1/16W,DA,TP,1005” 2007-000162 2 R249 R-CH
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 R180 R-CHIP “330ohm,5%,1/16W,DA,TP,1005” 2007-001313 2 R181 R-CHIP “330ohm,5%,1/16W,DA,TP,1005” 2007-001313 2 R182 R-CHIP “330ohm,5%,1/16W,DA,TP,1005” 2007-001313 2 R183 R-CHIP “330ohm,5%,1/16W,DA,TP,1005” 2007-001313 2 R184 R-CHIP “330ohm,5%,1/16W,DA,TP,1005” 2007-001313 2 R185 R-CHIP “330ohm,5%,1/16W,DA,TP,1005” 2007-001313 2 R186 R-CHIP “330ohm,5%,1/16W,DA,TP,1005” 2007-001313 2 R187 R-CHIP “33
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 R564 R-CHIP “68Kohm,1%,1/16W,DA,TP,1005” 2007-007589 2 R438 R-CHIP “2KOHM,1%,1/16W,DA,TP,1005” 2007-007766 2 L350 R-CHIP “0OHM,5%,1/16W,DA,TP,1005” 2007-007771 2 R174 R-CHIP “0OHM,5%,1/16W,DA,TP,1005” 2007-007771 2 R203 R-CHIP “0OHM,5%,1/16W,DA,TP,1005” 2007-007771 2 R207 R-CHIP “0OHM,5%,1/16W,DA,TP,1005” 2007-007771 2 R223 R-CHIP “0OHM,5%,1/16W,DA,TP,1005” 2007-007771 2 R321 R-CHIP “0OHM,5%,1/16W
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 C472 “C-CERAMIC,CHIP” “0.1nF,5%,50V,NP0,TP,1005” 2203-000233 2 C474 “C-CERAMIC,CHIP” “0.1nF,5%,50V,NP0,TP,1005” 2203-000233 2 C477 “C-CERAMIC,CHIP” “0.1nF,5%,50V,NP0,TP,1005” 2203-000233 2 C479 “C-CERAMIC,CHIP” “0.1nF,5%,50V,NP0,TP,1005” 2203-000233 2 C483 “C-CERAMIC,CHIP” “0.1nF,5%,50V,NP0,TP,1005” 2203-000233 2 C485 “C-CERAMIC,CHIP” “0.1nF,5%,50V,NP0,TP,1005” 2203-000233 2 C487 “C-CERAMIC,CHIP” “0.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 C414 “C-CERAMIC,CHIP” “10nF,10%,16V,X7R,TP,1005,-” 2203-000254 2 C420 “C-CERAMIC,CHIP” “10nF,10%,16V,X7R,TP,1005,-” 2203-000254 2 C423 “C-CERAMIC,CHIP” “10nF,10%,16V,X7R,TP,1005,-” 2203-000254 2 C425 “C-CERAMIC,CHIP” “10nF,10%,16V,X7R,TP,1005,-” 2203-000254 2 C460 “C-CERAMIC,CHIP” “10nF,10%,16V,X7R,TP,1005,-” 2203-000254 2 C461 “C-CERAMIC,CHIP” “10nF,10%,16V,X7R,TP,1005,-” 2203-000254 2 C463 “C-CERAMIC,
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 C432 “C-CERAMIC,CHIP” “1nF,10%,50V,X7R,TP,1005,-” 2203-000438 2 C434 “C-CERAMIC,CHIP” “1nF,10%,50V,X7R,TP,1005,-” 2203-000438 2 C442 “C-CERAMIC,CHIP” “1nF,10%,50V,X7R,TP,1005,-” 2203-000438 2 C443 “C-CERAMIC,CHIP” “1nF,10%,50V,X7R,TP,1005,-” 2203-000438 2 C451 “C-CERAMIC,CHIP” “1nF,10%,50V,X7R,TP,1005,-” 2203-000438 2 C457 “C-CERAMIC,CHIP” “1nF,10%,50V,X7R,TP,1005,-” 2203-000438 2 C453 “C-CERAMIC,CHIP”
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 C231 “C-CERAMIC,CHIP” “6.8nF,10%,25V,X7R,TP,1005,-” 2203-001101 2 C232 “C-CERAMIC,CHIP” “6.8nF,10%,25V,X7R,TP,1005,-” 2203-001101 2 C248 “C-CERAMIC,CHIP” “6.8nF,10%,25V,X7R,TP,1005,-” 2203-001101 2 C551 “C-CERAMIC,CHIP” “6.8nF,10%,25V,X7R,TP,1005,-” 2203-001101 2 C119 “C-CERAMIC,CHIP” “8.2nF,10%,16V,X7R,TP,1005,-” 2203-001210 2 C413 “C-CERAMIC,CHIP” “8.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 C321 “C-CERAMIC,CHIP” “100nF,+80-20%,16V,Y5V,TP,1005” 2203-005061 2 C333 “C-CERAMIC,CHIP” “100nF,+80-20%,16V,Y5V,TP,1005” 2203-005061 2 C334 “C-CERAMIC,CHIP” “100nF,+80-20%,16V,Y5V,TP,1005” 2203-005061 2 C352 “C-CERAMIC,CHIP” “100nF,+80-20%,16V,Y5V,TP,1005” 2203-005061 2 C353 “C-CERAMIC,CHIP” “100nF,+80-20%,16V,Y5V,TP,1005” 2203-005061 2 C355 “C-CERAMIC,CHIP” “100nF,+80-20%,16V,Y5V,TP,1005” 2203-005061 2
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 L307 “C-CERAMIC,CHIP” “0.005nF,0.1pF,50V,NP0,TP,1005” 2203-005393 2 C426 “C-CERAMIC,CHIP” “0.0047nF,0.1pF,50V,NP0,TP,1005” 2203-005395 2 C325 “C-CERAMIC,CHIP” “0.003nF,0.1pF,50V,NP0,TP,1005” 2203-005444 2 C344 “C-CERAMIC,CHIP” “0.003nF,0.1pF,50V,NP0,TP,1005” 2203-005444 2 C343 “C-CERAMIC,CHIP” “0.0056nF,0.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 C502 “C-TA,CHIP” “10UF,20%,6.3V,GP,TP,2012” 2404-001105 2 L411 INDUCTOR-SMD “180nH,10%,0.8x1.6x0.8mm” 2703-000143 2 L412 INDUCTOR-SMD “180nH,10%,0.8x1.6x0.8mm” 2703-000143 2 L312 INDUCTOR-SMD “470nH,10%,0.8x1.6x0.8mm” 2703-000213 2 L323 INDUCTOR-SMD “470nH,10%,0.8x1.6x0.8mm” 2703-000213 2 R140 INDUCTOR-SMD “220nH,10%,1.25x2x0.85mm” 2703-000266 2 L414 INDUCTOR-SMD “220nH,5%,2.29x1.73x1.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 2 SPK SPEAKER “0.075W,32ohm,104dB,-” 3001-001138 2 L403 CORE-FERRITE BEAD “AB,120OHM,1X0.5X0.5MM,150MA,TP,M 3301-001341 2 L405 CORE-FERRITE BEAD “AB,120OHM,1X0.5X0.5MM,150MA,TP,M 3301-001341 2 L409 CORE-FERRITE BEAD “AB,120OHM,1X0.5X0.5MM,150MA,TP,M 3301-001341 2 L440 CORE-FERRITE BEAD “AB,120OHM,1X0.5X0.5MM,150MA,TP,M 3301-001341 2 L443 CORE-FERRITE BEAD “AB,120OHM,1X0.5X0.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 4 PMO-HOUSING CAP “SPH-8000,POM,BLK,-,-” GH72-00059A 4 PMO-HINGE CAM “SPH-8000,POM,BLK,-,-” GH72-00060A 4 PMO-HINGE SHAFT “SPH-8000,POM,BLK,-,-” GH72-00061A 4 PMO-HINGE HOUSING “SPH-8000,POM,BLK,-,-” GH72-00064A MEC-SUA. FLIP “SCH-620,TELEFONICA,BLK” GH75-00428A 4 LABEL(R)-FLIP(BLK) “SCH-900,PC EMBO,30X4,T0.125,BLK” GH68-00278A 4 LABEL(M)-LOGO BADGE “SCH-500,NI,20.0X4.4,T0.
Electrical Parts List Level Design LOC ITEMS DESCRIPTIONS SEC CODE 3 PMO-REAR COVER “SCH-620,PC,BLK,-,K2261” GH72-00902A 3 MPR-REAR GASKET LEFT “SCH-611,BUJICPO,17X4.7,BLK,-” GH74-00360A 3 MPR-REAR GASKET RIGHT “SCH-611,BUJICPO,18.4X7.3,BLK,-” GH74-00361A 1 PAA MAIN-SCH620(BRAZ) “SCH-620,GLOBAL-TELECOM,BRAZ,-,-,-,-” GH99-02226A 2 LABEL(P)-SEAL “SP-R912,CRP,65.0x95.
Electrical Parts List No. 32 33 34 35 35 36 37 38 39 40 41 Design LOC LF1 L22 L21 C25 C4, C23, C24 C44 C34 C5, C7 C28, C30, C33, C42, C43, C45 C26 DESCRIPTIONS R-METAL FILM S/W TRANS LINE-FILTER COILCHOKE(TROIDAL) COIL-CHOKE (DRUM) CAP-CHIP CAP-CHIP CAP-CHIP CAP-CHIP CAP-CHIP CHT09, 0.
Electrical Parts List No. 80 Design LOC (U1) DESCRIPTIONS 81 82 PWR-CORD HEAT-SINK(U1) SCREW-TAP)U1) ADHESIVE-SEALANT 83 84 VINIL SACK SOLDER-WIRE 85 ALCOHL FLUX-SOLDER SEC CODE PH+, M3x6 DC739, 40RTV 0201-001029 0201-000303 170x350x0.05, WHITE KR-19, S60A, D1.0 0202-000178 0202-000193 0204-000429 MF02-00020A 0202-000226 ML74-00113A (CH3)2CHOM 920-CFX REMARKS D3, 0, Sn60% SOLDER-WIRE 8-3 Hands-Free Kit Part List No.
Electrical Parts List No. 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 Design LOC LABEL BAR CODE LABEL BAR CODE MANUAL POLYBAG POLYBAG CABLE TIE POWER LOG SCREW SCREW BOX ACCESSORY UNIT BOX PACKING PAD OUTER BOX CASE FRONT CASE REAR HANDLE SPEAKER BOLT HEX.
Electrical Parts List No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Design LOC DESCRIPTIONS R119, R268 R275 R57, R233, R248 R5, R10, R17, R20, R23,R27 R30, R33, R41, R44 R45, R46, R55, R56, R100.
Electrical Parts List No.
Electrical Parts List Design LOC No. 1 2 3 DESCRIPTIONS REMARKS SEC CODE REMARKS SEC CODE REMARKS CMP-68 4 ohm 5W 4 PIN POWER CABLE ASS'Y MIC ASS'Y SPEAKER ASS'Y POWER CABLE Design LOC No. SEC CODE DESCRIPTIONS 1 2 3 RESISTOR RESISTOR RESISTOR CH 2012 330 ohm-J 5% CH 2012 2.2K-J 5% CH 2012 1K-J 5% 4 5 6 7 8 9 10 11 CONNECTOR WAFER CONNECTOR WAFER PHOTO INT. THERMOSTOR LED (LED TACK) COILD CORD CABLE DATA CABLE P.C.
Electrical Parts List Design LOC No. DESCRIPTIONS 22 C8 CE. CAP 23 24 25 26 27 28 29 30 31 C3 C6 TH F1 SK2 Q7 R2 R14, 15, 16 JP1, 2, 3 CE. CAP MY. CAP THERMISTOR MICRO FUSE CONN. HEADER S.S. TR CHIP RESI CHIP RESI CHIP RESI 32 R66, 67 CHIP RESI 33 34 JP4, 5 R57 CHIP RESI CHIP RESI 35 R58 CHIP RESI 36 R17 CHIP RESI 37 R1 CHIP RESI 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 R59 C23 C5 C25, 26, 27, 28, 29, 30 U3 MICOM IC P.C.
Electrical Parts List 8-5 CLA Parts List No.
Electrical Parts List No. 54 55 56 57 Design LOC HANISHELLL OUT BOX CURRUGATED PAD CLA SPONGE DESCRIPTIONS SEC CODE +PH (2.
9.
Block Dirgrams 9-2 CLC BLOCK DIRGRAM SAMSUNG Proprietary-Contents may change without notice 9-2
MEMO SAMSUNG Proprietary-Contents may change without notice 9-3
10.
PCB diagrams 10-2 Main PCB Bottom Diagram Samsung Electronics 10-2
PCB diagrams 10-3 CLC PCB Top Diagram 10-4 CLC PCB Bottom Diagram Samsung Electronics 10-3
PCB diagrams 10-5 Hands-free Kit PCB Top Diagram Samsung Electronics 10-4
11. Circuit Diagrams 11-1 Logic & Audio & Power Circuit Diagram 2 1 4 3 6 5 7 9 8 11 10 12 +3.0V +3.0V +3.0V 6D C102 4 7 0 PF +3.
Circuit diagrams 11-2 TX & RX & LOCAL Circuit Diagram 3 2 1 5 4 6 8 7 9 10 12 11 +3.0V C3 8 4 1 0 NF R5 5 8 F3 0 3 C3 5 1 C3 5 2 100P F 100NF R306 1K C324 1 0 0 PF R300 NC C306 1 8 PF C312 1 NF B Q3 0 2 L 304 1 5nH C307 1 NF L 307 5 PF L 350 0 I N C308 1 0 0 PF 2 L 313 8 . 2nH 5 GND L 308 NC +3.0RL L 305 8 2nH L 303 NC R305 3 . 3M R314 2 20 R304 82 1 CN5 0 1 3 1 L 516 8 . 2nH C522 1 0 0 PF 3 T X_ 1 S T _ L O C525 1 0 0 PF 4 3 6 L 511 6 .
Circuit diagrams 11-3 CLC Circuit Diagram Samsung Electronics 11-3
ELECTRONICS ©Samsung Electronics Co.,Ltd. APRIL. 2000 Printed in Korea. Code No.: GH68-00669A BASIC.
