User Guide

5-4
Samsung Electronics
Test Procedure
Command No. Signal. Name Description
(OP, AB, RB)
68(C8, 0, 3) T_VBATT1_I Set the low battery position in the standby.
69(C9, 0, 3) T_VBATT2_I Set the low battery position in the talking.
70(CA, 3, 0) T_WRITE_BATT_I Write low battery level value to NVM.
71(D1, 3, 0) T_CDMA_TXADJ_I Change PDM TX AGC in CDMA.
72(D2, 3, 0) T_FM_TXADJ_I Change PDM TX AGC in FM.
73(D3, 1, 0) T_SET_PA_R_I Set PA R1, R0 in CDMA.
74(D4, 3, 0) T_TXADJ_0DBM_I Set TX AGC ADJ for 0dBm power.
75(D5, 0, 3) T_READ_RSSI_I Read a RSSI.
76(D6, 3, 0) T_WRITE_RSSI_I Writes RSSI.
77(D7, 0, 3) T_READ_TEMP_I Read Temp.
79(D9, 1, 0) T_BUZZER_ON_I Buzzer On at DTMF 0 key.
80(DA, 0, 0) T_BUZZER_OFF_I Buzzer off.
81(E3, 0, 0) T_VOC_PCMLPON_I Play a PCM LOOP BACK.
82(E4, 0, 0) T_VOC_PCMLPOFF_I Play off a PCM LOOP BACK.
84(E6, 3, 0) T_CD_MAX_LIMIT_I CDMA MAX limit.
85(E7, 0, 0) T_SPEAKER_ON_I Turn on the speaker path.
86(E8, 0, 0) T_SPEAKER_OFF_I Turn off the speaker path.
87(E9, 0, 0) T_FM_LOOP-TEST_I Play a PCM FM loopback.
88(EA, 3, 0) T_TRK_ADK_I TRK LOCAL ADJUST.
89(EB, 3, 0) T_CD_TRK_ADJ_I CDMA TRK LOCAL ADJUST.
90(F0, 3, 0) T_CDMA_LOW_CH_HIPWR_I Setting the volume for LOW CH highpwr. (+18dBm)
91(F1, 3, 0) T_CDMA_LOWMID_CH_HIPWR_I Setting the volume for LOWMID CH highpwr. (+18dBm)
92(F2, 3, 0) T_CDMA_MIDDLE_CH_HIPWR_I Setting the volume for MIDDLE CH highpwr. (+18dBm)
93(F3, 3, 0) T_CDMA_LOW_CH_LOPWR_I Setting the volume for LOW CH lowpwr. (-41dBm)
94(F4, 3, 0) T_CDMA_LOWMID_CH_LOPWR_I Setting the volume for LOWMID CH lowpwr. (-41dBm)
95(F5, 3, 0) T_CDMA_MIDDLE_CH_LOPWR_I Setting the volume for MIDDLE CH lowpwr. (-41dBm)
96(F6, 3, 0) T_CDMA_HIGHMID_CH_LOPWR_I Setting the volume for HIGHMID CH lowpwr. (-41dBm)
97(F7, 3, 0) T_CDMA_HIGH_CH_LOPWR_I Setting the volume for HIGH CH lowpwr. (-41dBm)
98(F8, 3, 0) T_CDMA_HIGHMID_CH_HIPWR_I Setting the volume for HIGHMID CH highpwr. (+18dBm)
99(F9, 3, 0) T_CDMA_HIGH_CH_HIPWR_I Setting the volume for HIGH CH highpwr. (+18dBm)
¶S
OP: Operation Command Number
AB: Input Argument Byte Number
RB: Return Byte Number