CDMA PORTABLE PCS TELEPHONE SCH-1000 SERVICE CDMA PORTABLE PCS TELEPHONE Manual CONTENTS 1. Specification 2. Installation 3. NAM Programming 4. Circuit Description 5. Test Procedure 6. Troubleshooting 7. Exploded Views and Parts List 8. PCB Diagrams 9. Electrical Parts List 10.
Samsung Electronics Co.,Ltd. GH68-60563A Printed in Korea.
1. Specification 1-1 General Frequency Range Transmitter Receiver : 1850 ° ≠1910 MHz : 1930 ° ≠1990 MHz Channel Bandwidth : 1.23 MHz Channel Spacing : 50 KHz Number of Channels : 1200 Duplex Separation : 80 MHz Type of Emission : G7W Input/Output Impedance : 50 ohms Intermediate Frequency Transmitter Receiver : 130.38 MHz : 85.38 MHz Local Frequency Transmitter Receiver : 1st(FTX-130.38), 2nd(260.76MHz) : 1st(FRX+85.38), 2nd(170.76MHz) TCXO Frequency : 19.
Specification 1-2 Transmitter Waveform Quality : 0.944 or more Open Loop Power Control Range -25 dBm -65 dBm -104dBm : -60.5dBm ° ≠-41.5dBm : -20.5dBm ° ≠-1.5dBm : +15.0dBm ° ≠+30.0dBm Minimum Tx Power Control : -50dBm below Closed Loop Power Control Range : °æ24dB Maximum RF Output Power : 200mW(+23dBm) Occupied Bandwidth : 1.23MHz Conducted Spurious Emissions @1.25MHz : -42 dBc/30KHz 1-3 Receiver Rx Sensitivity and Dynamic Range (Rate Set 1) : -104dBm, FER=0.5% or less : -25 dBm, FER=0.
2. Installation 2-1 Installing a Battery Pack 1. 2. To attach the battery pack after charging, align it with the phone about 1cm (1/2") away from its place so that the two arrows on the phone are seen, the battery charge contacts pointing downwards. 3. To remove the battery pack, release it by pressing the button on the rear of the phone. 4. Slide the battery pack downwards about 1cm (1/2") and lift it away from the phone. Slide the battery pack upwards until it clicks firmly into position.
Installation 2-3 For Mobile Mount 2-3-1 Antenna 2-3-2 Cradle 1. Choose a proper location to install the antenna. ¶UThe center of the roof top provides the best performance. ¶UThe edge of the rear trunk also provides a good performance. However, the antenna should be higher than the roof of the car. ¶UIn case of on-glass antenna, you should align the antenna base with the round plate to connect the cables correctly. 1.
Installation 2-3-3 Hands-Free Box 2-3-4 Hands-Free Microphone 1. Drill holes in a proper location for the handsfree box, attach the mounting bracket by using the screws. See the figure 2-3. 1. 2. Install the hands-free box into the bracket. It is recommended to install the microphone where it is 30-45 cm (12-18") away from the driver. Choose the location where is least susceptible to interference caused by external noise sources, ie, adjacent windows, radio speakers, etc.
Installation 2-3-5 Cables 1. Connect the cradle and the hands-free box with the data cable. See the figure 2-4. 2. Connect the antenna cable to the RF jack of the cradle. 3. Connect one end of the power cable to the battery or ignition terminal. Connect the red wire to the battery (+) terminal, black wire to the vehicle chassis. Then connect the battery (-) terminal to the vehicle chassis. 4. Connect the other end of the power cable to the PWR jack of the hands-free box.
3. NAM Programming NAM features can be programmed as follows: Notes: -If you enter the NAM program mode, each item shows the currently stored data. Go to the next item by pressing STO. -You can modify the data by entering a new data. -If you enter a wrong digit, press CLR to delete the last digit. Press and hold CLR to delete all digits. -To scroll items backwards or forwards, press the VOLUME button on the left side of the phone.
NAM Programming 3-2 Setting Up NAM LCD Display Key in Function SVC Menu°Ë°È 1:PCS Phone # 2:General Volume °„ -NAM Programming Menu is displayed SVC Menu°Ë°È 3:NAM 3 -choose 'Setup NAM' IMSI_MCC 310 number STO IMSI Mobile Country Code, current code is displayed. -to change, enter new one. -stores it. 00 number STO IMSI Mobile Network Code, current code is displayed. -to change, enter new one. -stores it. IMSI_MNC class number STO CDMA Access Over load Class, current status is displayed.
4. Circuit Description 4-1 Logic Section 4-1-1 Power Supply With the battery installed on the phone and by pressing the PWR key, the VBATT and ON_SW signals will be connected. This will turn on Q108(2SC4081). This in turn will be supplied to pin 6 of regulators U110 and U111, thus releasing them from the shut-down state to output regulated 3.3V. And then Reset Generator (U109) stays High.
Circuit Description 4-1-3 Base Band MOBILE SYSTEM MODEM (MSM) The MSM equipped with the INTEL 80186 CPU core is an important component of the CDMA cellular phone. The MSM comes in a 176 pins TQFP package. The interface block diagram is shown on page4-3. ADC Interface MICROPROCESSOR INTERFACE Data Port Interface The interface circuitry consists of reset circuit, address bus (A0-A19), data bus (AD0-AD15), and memory controls (ALE,DT-R,HWR/,LWR/, RAM_CS/,ROM_CS). Includes the UART.
Circuit Description Figure 4-1 Baseband Block Diagram 4-1-4 Audio Section 4-1-5 Buzzer Driving Circuitry TX AUDIO PATH Buzzer generates alert tone. When the buzzer receives the timer signal from the MSM, it generates alert tone. The buzzer level is adjusted by the alert signal's period generated from the MSM timer. The voice signal output from microphone is filtered and amplified by the internal OP-AMP and is converted to PCM data by the CODEC(U102).
Circuit Description 4-2 Receiver Section LOW NOISE AMPLIFIER (LNA) BUFFER The low noise amplifier featuring 1.6dB Noise Figure and 19dB gain amplifies a weak signal received from the base station to obtain the optimum signal level. Buffer (Q311) amplifies the signal from the VCO (U305) to be applied to the local input of the down converter (U302) when a phase is locked between U304 and U305. DOWN CONVERTER (MIXER) First local signal is applied to this down converter.
Circuit Description 4-3 Transmitter Section POWER AMP MMIC ANTENNA Power Amp MMIC (U407) amplifies signal to be sent out to the base station through the antenna. ANT1 allows signals to send and to receive to from the base station. DRIVER AMP RF BAND PASS FILTER (BPF) The driver amp (Q411,Q413) allows the input signal to the power amp MMIC(U407) to be within a specified level. The RF BPF (F402) accepts only a specific frequency (1880°æ30MHz) to send it out to power amp MMIC. The bandwidth is 60MHz.
Circuit Description 4-4 Hands-Free Kit Hands free board is largely composed of car adapter circuit and Hands free circuit. 4-4-1 Car Adapter Circuit POWER SUPPLY Input power switching circuit : This circuit includes Short protection circuit, and Power switching control circuit. It supplies power for HHP and hands free kit. +13.5V switching circuit (Q801, 802) : This circuit switches power for power amplifier using MPU mute signal. HHP power circuit : This circuit is Switching regulator.
Circuit Description 4-5 Desk-Top Rapid Charger 4-5-1 Description The following document will provide the specifications for SAMSUNG-SPRINT's battery charger unit, system #PCS, which be sold as an accessory to cellular telephone, model SCH1000/RC. The bettery charger sequentially charges two NiMH batteries that are to be used with the cellular telephone. The first slot will be able to accommodate a battery attached to the cellular telephone. The second slot can be used a spare battery.
Circuit Description BATTERY CHARGING CURRENT LED INDICATION • EXTENDED BATTERY : 900mA °æ 10% • STANDARD BATTERY : 630mA °æ 10% • DC POWER ON : Instantaneous YELLOW flickering of both LED. • SLOT INDENTIFICATION LED 'LEFT' : FRONT SLOT (PHONE) LED 'RIGHT' : REAR SLOT (BATT) • CHARGING STATUS RED : CHARGING GREEN : CHARGING TERMINATION (Full Charge) YELLOW : LOW BATTERY (WAIT) FLASHING YELLOW : DISCHARGING FLASHING R °Ê G °Ê Y, FLASHING RED : Hardware Error. OFF : BATTERY UNLODED, etc...
Circuit Description PROTECTION CIRCUIT FOR EXCESSIVE VOLTAGE The norminal voltage of Zener diode D2 is 22V and the reverse voltage by leakage current is about 14.5V. If the input voltage is under 22V, the Q1 stays off and the gate of FET Q2 becomes low level and turns on main path. If the voltage is higher than 22V or excessive impulsive voltage is supplied, D2 becomes breakdown and turns on Q1 and turns off Q2 by raising the gate voltage to high level.
Circuit Description CHARGE MAIN PATH BATTERY TEMPERATURE DETECTION MPU turns on Q8 or Q9 with high level output from pin 2 for front port and pin 1 for rear port. Q8 and Q9 pull down the base voltage level of PNP TRQ3 and Q4. It turns on main path, then charging is started. The temperature of the battery pack in the front port and rear port is detected by R36/R37 and R34/R35, respectively, and measured as A/D value at MPU pin 15.
Circuit Description WATCH DOG DISCHARGE CIRCUIT It is possible that battery is overcharged if charger stops operation by keeping on charging port by external impact. To avoid it, timer (U3-B) is prepared and MPU is forced to be reset if MPU dosen't clear timer until a specified time is elapsed. Discharging battery is available in the rear port and initiated once pin 22 of MPU acknowledges the depression of discharge switch.
Circuit Description 4-6 Cigarette Lighter Adapter 4-6-1 Funtional Specification SUMMARY FUNCTIONS OF CLA This standard describes on the specifications of CLA(Cigarette Lighter Adaptor) for the SCH-1000 of SAMSUNG. CLA AS ADAPTOR AND CHARGER ¶UAdaptor directly supplies power in order to operate cellular phone independent of the battery pack. ¶UCharger for the NiMH battery pack ELECTRICAL SPECIFICATION ¶UInput Voltage : 11V to 16.5V DC (normal voltage : 13.
Circuit Description 4-6-2 Schematic Description DC-DC CONTROLLER PREVENT CHARGE CIRCUIT IN THE CASE OF MOBILE PHONE CARRIER-ON KA7500B(U1) is DC-DC Controller. It reads the voltage difference between E1I+ Port and E1I- Port and controls time to turn on Q1. E2I+ and E2Iturn on Q1 in the same way. U1 also supplies +5V of Reference Voltage(Vref). In the case of Mobile Phone carrier-on, the voltage loaded on PIN-13 of U3D is lower than that of PIN-12. So PIN-14 ouputs HIGH and Q3 is TURN ON again.
Circuit Description 4-7 Travel Charger 4-7-1 Description This document defines the functional requirements of SCH-110TC, SCH-1000TC, designed as a Ni-MH battery charger for SCH-110, SCH-1000. This charger can be used with indoor AC input directly. One LED indicates charging status of battery. Charging current mode is constant current mode controled. 4-7-2 Scope This specification is applied to every unit of model no. SCH-110TC, SCH-1000TC, revision level 0. - EFFICIENCY : 50% min.
Circuit Description 4-7-5 Mechanical Specification - CASE SIZE : 140.8mm°ø54.4mm°ø23.9mm - CASE MATERIAL : PC (LEXAN 940) - COLOR : BLACK - WEIGHT : 110g 4-7-6 Explanation Of Operating BASIC CIRCUIT CONFIGURATION Ttavel charger is consisted with power supply and charging controller, And this charger is also specified to input filter, rectifier, transformer, secondary filter, feed-back circuit, battery charging control circuit and LED display.
Circuit Description Supplied current is converted to voltage by R21. U22A compares this to the reference, which is divided voltage by r30, r31 and r28, and transfers difference to PWM control circuit by U21 and OP1. so this charger offers constant current to battery. U23B compares the voltage of Term. #6 to it of Term. #5, this is reference and that is sampling voltage of battery. U23B makes U24A to ON state by decreased the voltage of U24A Term.
5.
Test Procedure 5-3 Test Procedure 5-3-1 Change to Test Mode 1. To change the phone from Normal Mode to test Mode, You should enter the following keys. "47*869#1235" 2. The command° ∞ 0 1"(Suspend) is entered to start test. 3. To finish the Test Mode, You should enter the command "0 2". 5-3-2 Channel Selection and Tx Power Output level Control 1. You should change the phone from Normal Mode to Test mode 2. The command° ∞ 0 1"(Suspend) is entered to start test. 5-2 3. You should enter the following keys.
Test Procedure 5-4 Test Command Table Command No.
Test Procedure Command No. (OP, AB, RB) Signal. Name Description 68(C8, 0, 3) T_VBATT1_I Set the low battery position in the standby. 69(C9, 0, 3) T_VBATT2_I Set the low battery position in the talking. 70(CA, 3, 0) T_WRITE_BATT_I Write low battery level value to NVM. 71(D1, 3, 0) T_CDMA_TXADJ_I Change PDM TX AGC in CDMA. 72(D2, 3, 0) T_FM_TXADJ_I Change PDM TX AGC in FM. 73(D3, 1, 0) T_SET_PA_R_I Set PA R1, R0 in CDMA. 74(D4, 3, 0) T_TXADJ_0DBM_I Set TX AGC ADJ for 0dBm power.
6.
Troubleshooting 6-1-2 Abnormal Initial Operation (Normal +3.
Troubleshooting 6-1-3 Abnormal Backlight Operation Samsung Electronics 6-3
Troubleshooting 6-1-4 Abnormal Key Data Input 6-4 Samsung Electronics
Troubleshooting 6-1-5 Abnormal Keytone Samsung Electronics 6-5
Troubleshooting 6-1-6 Abnormal Alert Tone 6-6 Samsung Electronics
Troubleshooting 6-2 Transmitter Section Samsung Electronics 6-7
Troubleshooting 6-8 Samsung Electronics
Troubleshooting 6-3 Receiver Section Samsung Electronics 6-9
Troubleshooting 6-10 Samsung Electronics
Troubleshooting Samsung Electronics 6-11
Troubleshooting 6-4 Hands-Free Car Kit 6-4-1 Abnormal Battery Charging A: 2.47V °¬ V at U703 pin 1 < 2.98V B: 1.53V °¬ V at U703 pin 1 < 2.
Troubleshooting 6-4-2 No Power (HHP PWR +5.8V, +13.
Troubleshooting 6-4-3 Hands-Free RX Path 6-14 Samsung Electronics
Troubleshooting 6-4-4 Hands-Free TX Path Samsung Electronics 6-15
Troubleshooting 6-5 Desk-Top Rapid Charger 6-16 Samsung Electronics
Troubleshooting 6-6 Cigarette Lighter Adapter 6-6-1 Power Fault Samsung Electronics 6-17
Troubleshooting 6-6-2 LED-On Fault 6-18 Samsung Electronics
Troubleshooting 6-6-3 Charge Fault Samsung Electronics 6-19
Troubleshooting 6-7 Travel Charger 6-20 Samsung Electronics
7.
Exploded View and its Parts List 7-1 Main Set Exploded View 7-2 Samsung Electronics
Exploded View and its Parts List 7-2 Main Set Parts List NO DESCRIPTION SEC.
Exploded View and its Parts List 7-3 Hands-Free Kit Exploded View 7-4 Samsung Electronics
Exploded View and its Parts List 7-4 Hands-Free Kit Parts List NO DESCRIPTION SEC.
Exploded View and its Parts List 7-5 Hands-Free Kit Cradle Exploded View 7-6 Samsung Electronics
Exploded View and its Parts List 7-6 Hands-Free Kit Cradle Parts List NO DESCRIPTION SEC. CODE 1 UPPER HOUSING-C/D GH72-40014A 1 2 SOCKET PLATE-C/D GH70-10526A 1 3 TORSION SPRING-C/D GH70-40002A 2 4 EJECTOR SPRING-C/D GH70-10520A 2 5 LOCKER-C/D GH72-40013A 2 6 FRAME-C/D GH72-40011A 1 7 SCREW, TAPTITE, B, BH, M2.6, L6 6003-000107 4 8 SCREW, TAPTITE, BH, M2.
Exploded View and its Parts List 7-7 Desk-Top Rapid Charger Exploded View 7-8 Samsung Electronics
Exploded View and its Parts List 7-8 Desk-Top Rapid Charger Parts List NO DESCRIPTION 1 CASE TOP 1 2 LABEL-LOGO DTC 1 3 HOOK PLATE (L) 1 4 HOOK PLATE (R) 1 5 HOUSING BATT 1 6 TAPPING SCREW 4 7 TAPPING SCREW 8 MAIN PBA 1 9 INSULATION PAPER 1 10 KNOB 1 11 CASE BOTTOM 1 12 TAPPING SCREW 4 13 FOOT RUBBER 4 14 LABEL-DTC 1 Samsung Electronics SEC.
Exploded View and its Parts List 7-9 Cigarette Lighter Adapter CIGARETTE LIGHTER ADAPTER ASS'Y : GH44-40012A 7-10 Samsung Electronics
Exploded View and its Parts List 7-10 Travel Charger TRAVEL CHARGER ASS'Y : GH44-40011A Samsung Electronics 7-11
Exploded View and its Parts List 7-11 Main Set Packing Layout 7-12 Samsung Electronics
Exploded View and its Parts List 7-12 Main Set Packing Parts List NO DESCRIPTION SEC. CODE 1 GIFT BOX MAIN GH69-10884A 1 2 CUSHION CASE-MAIN GH69-20558A 1 3 GIFT BOX-DTC GH69-10885A 1 4 GIFT BOX-ADAPTER GH69-10886A 1 5 MAIN SET 6 DESK TOP CHARGER GH90-00611A 1 7 AC ADAPTER GH44-30526A 1 8 STD BATT.
Exploded View and its Parts List 7-13 Hands-Free Kit Packing Layout 7-14 Samsung Electronics
Exploded View and its Parts List 7-14 Hands-Free Kit Packing Parts List NO DESCRIPTION SEC.
Exploded View and its Parts List 7-16 Samsung Electronics
9. Electrical Parts List 9-1 Handset NO DESCRIPTION SEC. CODE REMARK - Capacitors C101 Ceramic, Chip, 47nF 2203-001432 C102 Ceramic, Chip, 33nF 2203-001416 C104 Ceramic, Chip, 100nF 2203-000178 C105 Ceramic, Chip, 8.2nF 2203-001210 C106, C107 Ceramic, Chip, 100nF 2203-000178 C108 Ceramic, Chip, 680F 2203-001124 C109 Ceramic, Chip, 390pF 2203-000836 C110 Ceramic, Chip, 3.
Electrical Parts List NO DESCRIPTION SEC.
Electrical Parts List NO DESCRIPTION SEC. CODE C333, C334 Ceramic, Chip, 10nF 2203-000254 C335, C336 Tantalum, Chip, 10uF 2404-000139 C337, C338 Ceramic, Chip, 10nF 2203-000254 C339 Ceramic, Chip, 100nF 2203-000178 C340-C342 Ceramic, Chip, 100pF 2203-000233 C343 Ceramic, Chip, 10nF 2203-000254 C344 Ceramic, Chip, 100pF 2203-000233 C345 Ceramic, Chip, 10pF 2203-000278 C346 Ceramic, Chip, 1nF 2203-000438 C347 Ceramic, Chip, 100pF 2203-000233 C348 Tantalum, Chip, 1.
Electrical Parts List NO DESCRIPTION SEC. CODE C431 Ceramic, Chip, 100nF 2203-000178 C432 Ceramic, Chip, 100pF 2203-000233 C433 Ceramic, Chip, 100nF 2203-000178 C434 Tantalum, Chip, 1.5uF 2404-000274 C435 Ceramic, Chip, 2.2nF 2203-000489 C436, C437 Ceramic, Chip, 10pF 2203-000278 C439 Ceramic, Chip, 100nF 2203-000178 C440 Ceramic, Chip, 1.
Electrical Parts List NO DESCRIPTION SEC.
Electrical Parts List NO DESCRIPTION SEC. CODE REMARK - Diodes D101, D102 Diode, Array, KDS2 0407-000122 D103 Diode, Array, DAN202 0407-000115 D104 LED, Chip, RED, 2.0 0601-000355 D105 Diode, Array, DAN202 0407-000115 D106, D107 Diode, Array, KDS2 0407-000122 D108, D109 Diode, MMBZ5234 0403-000283 D401 ~ D403 Diode, ISV229 0405-000107 D406 Diode, ISV229 0405-000107 - Filters F301 Filter, Duplexer 2909-001037 F302 Filter, SAW, 1960MHz 2904-001021 F303 Filter, SAW, 85.
Electrical Parts List NO DESCRIPTION SEC. CODE L403 Inductor, SMD, 1uH 2703-000300 L405 Inductor, SMD, 100nH 2703-001049 L407 Inductor, SMD, 4.7nH 2703-001165 L408 Chip, 0ohm, 5% 2007-000171 L410 Inductor, SMD, 680nH 2703-000296 L412, L413 Inductor, SMD, 2.7uH 2703-000301 L414, L415 Inductor, SMD, 1uH 2703-000300 L416 Inductor, SMD, 2.2nH 2703-001288 L421 Inductor, SMD, 750nH 2703-000237 L422 Inductor, SMD, 2.2nH 2703-001205 L423, L424 Inductor, SMD, 2.
Electrical Parts List NO DESCRIPTION SEC. CODE REMARK - Resistors R101 Chip, 470ohm, 5% 2007-000932 R102 Chip, 10Kohm, 5% 2007-000148 R103 Chip, 0ohm, 5% 2007-000171 R104 Chip, 47K, 5% 2007-000157 R105 Chip, 22Kohm, 5% 2007-000153 R106 Chip, 1Kohm, 5% 2007-000140 R107 Chip, 22Kohm, 5% 2007-000153 R108 Chip, 47K, 5% 2007-000157 R109 Chip, 82Kohm, 5% 2007-000161 R110 Chip, 47K, 5% 2007-000157 R111 Chip, 4.
Electrical Parts List NO DESCRIPTION SEC. CODE R147, R148 Chip, 100Kohm, 5% 2007-000162 R149-R152 Chip, 20K, 5% 2007-000152 R154 Chip, 10Kohm, 5% 2007-000148 R155 Chip, 91Kohm, 5% 2007-001244 R156 Chip, 1Kohm, 5% 2007-000140 R157, R158 Chip, 10ohm, 5% 2007-000172 R159 Chip, 22Kohm, 5% 2007-000153 R160 Chip, 3.
Electrical Parts List NO DESCRIPTION SEC. CODE R314 Chip, 390ohm, 5% 2007-007095 R315 Chip, 47K, 5% 2007-000157 R316 Chip, 100ohm, 5% 2007-000138 R317 Chip, 1Kohm, 5% 2007-000140 R318 Chip, 100ohm, 5% 2007-000138 R319 Chip, 1.5Kohm, 5% 2007-000242 R330 Chip, 56Kohm, 5% 2007-000159 R333, R334 Chip, 8.2Kohm, 5% 2007-000147 R335 Chip, 15Kohm, 5% 2007-000151 R401 Chip, 10Kohm, 5% 2007-000148 R402 Chip, 1.
Electrical Parts List NO DESCRIPTION SEC. CODE R443 Chip, 22Kohm, 5% 2007-000153 R444 Chip, 8.2Kohm, 5% 2007-000147 R445 Chip, 12K, 5% 2007-000149 R446 Chip, 1Kohm, 5% 2007-000140 R447 Chip, 470ohm, 5% 2007-000932 R448 Chip, 4.7Kohm, 5% 2007-000143 R449 Chip, 180ohm, 5% 2007-001307 R450 Chip, 4.7Kohm, 5% 2007-000143 R451 Chip, 24ohm, 5% 2007-000618 R452 Chip, 4.7Kohm, 5% 2007-000143 R453 Chip, 10, 5% 2007-000172 R454 Chip, 10Kohm, 5% 2007-000148 R455 Chip, 4.
Electrical Parts List NO DESCRIPTION SEC. CODE REMARK - IC's U101 IC, Data COMM.
Electrical Parts List 9-2 Hands-free Car Kit 9-2-1 SCH-1000 HFK NO DESCRIPTION SEC. CODE REMARK - Capacitors C701, C702 Chip, 0.1U 2203-000204 C703, C704 Chip, 3P 2203-000874 C705, C706 0.01U 2203-000260 C713 Chip, 0.1U 2203-000204 C714 Tantalum, 10U, 10V 2404-000120 C721, C722 Tantalum, 2.2U, 35V 2404-000292 C723 0.01U 2203-000260 C730, C731 1000U, 16V 2401-000039 C732 Chip, 0.
Electrical Parts List NO DESCRIPTION SEC. CODE C833, C834 0.01U 2203-000260 C835, C836 Chip, 0.1U 2203-000204 C837 470U, 25V 2401-001781 C838 Chip, 0.1U 2203-000204 C839 0.01U 2203-000260 C840 100U, 16V 2401-000042 C841 Chip, 0.1U 2203-000204 C842 1000U, 16V 2401-000135 C845 Chip, 0.1U 2203-000204 C856 Chip, 0.1U 2203-000204 C861-C863 Chip, 0.1U 2203-000204 C864, C865 Tantalum, 10U, 10V 2404-000120 C866 Chip, 0.
Electrical Parts List NO DESCRIPTION SEC.
Electrical Parts List NO DESCRIPTION SEC. CODE R767 Chip, 22K 2007-000094 R768, R769 Chip, Inductor, 1M 2007-000109 R770 Chip, 10K 2007-000090 R771 Chip, 100K 2007-000102 R772 Chip, 100K 2007-000102 R781, R782 Chip, 22K 2007-000094 R787 Chip, 100K 2007-000102 R788 Chip, 10K 2007-000090 R789 Chip, Inductor, 1M 2007-000109 R790 Chip, 10K 2007-000090 R791 Chip, 4.
Electrical Parts List NO DESCRIPTION SEC. CODE R830 Chip, 10K 2007-000090 R832 Chip, 330K 2007-000133 R833 Chip, 120K 2007-000103 R834 Chip, 3.3 2007-000695 R842 Chip, 180K 2007-000132 R843 Chip, 120K 2007-000103 R844 Chip, 82K 2007-000101 R845 Chip, 56K 2007-000098 R846 Chip, 33K 2007-000134 R847 Chip, 15K 2007-000092 R848 Chip, 5.
Electrical Parts List 9-2-2 SCH-1000 Cradle NO DESCRIPTION SEC.
Electrical Parts List 9-3 Desk-Top Rapid Charger NO DESCRIPTION SEC. CODE REMARK - Capacitors C1 Electrolytic, 100ßfi, 25V C2, C3 Chip, 0805, 0.1uF, K (104) C4 Electrolytic, 100ßfi, 16V C5 Electrolytic, 470ßfi, 25V C6 Chip, 0805, 0.1uF, K (104) C8, C9 Electrolytic, 10ßfi, 16V C10, C11 Chip, 0805, 220pF, J (221) C13 Chip, 0805, 0.1uF, K (104) C14 Chip, 0805, 220pF, J (221) C15, C16 Chip, 0805, 0.
Electrical Parts List NO DESCRIPTION SEC. CODE REMARK - Coil L1 Coil, Choke, 220uH - Transistors - Q1 PNP, SOT-23, -50V, -100mA, 200mW, KSR2102 PNP, SOT-23, -50V, -100mA, 200mW, KRA102S Q2 FET, P-Channel, D-Pack, -50V, -9.9A, 0.
Electrical Parts List NO DESCRIPTION R15 Chip, 0805, 4.7Kߟ, J R16-R19 Chip, 0805, 30ߟ, J R20 1/4W, 470ߟ, F R21 2W, 75ߟ, F R22, R23 Chip, 0805, 2.2Kߟ, J R24 Chip, 0805, 12Kߟ, J R25 Chip, 0805, 22Kߟ, J R26 Chip, 0805, 12Kߟ, J R27-R29 Chip, 0805, 22Kߟ, J R30, R31 Chip, 0805, 2.2Kߟ, J R32, R33 Chip, 0805, 12Kߟ, J R34 Chip, 0805, 4.7Kߟ, F R35 Chip, 0805, 12Kߟ, F R36 Chip, 0805, 4.
Electrical Parts List NO DESCRIPTION SEC. CODE REMARK - Miscellaneous SW1 Switch, KPT1105S TH1 Thermist.or, 10Kߟ/25°…, NTH300XQ103E01 Thermist.or, 10Kߟ/25°…, TG310H37 X1 X-Tal, 4MHz, 18PF, 49S-4MHz-18pF X-Tal, 4MHz, 18PF, HC491S/4M-18P DC, Jack Case, Top, PCS_GA1 Case, Bottom, PCS_GA2 Battery, Housing, PCS_GA3 S/W, KNOB, PCS_GA4 Contact, Base, PCS_GA5 Terminal, PCS_GB1 Hook, Ass'y, Right, PCS_GB2 Hook, Ass'y, Left, PCS_GB3 Label, PCS_GC1 Bumpon, 10°ø1.6t, PCS_GC2 Label, 8°ø8°ø0.
Electrical Parts List 9-4 Cigarette Lighter Adapter NO DESCRIPTION SEC. CODE REMARK - Capacitors C1 Electrolytic, 100u, 25V, CESSL1E101M0611AB C2 Chip, 1000P, CL10B102KBNCA C3 Electrolytic, 200u, 16V, CESSL1C221M0812AB C4 Chip, 0.1u, CL21B104KNER C6, C7 Tantalum, Chip, 4.7u, 6.3V, TCSCS0J475MAAR C9, C10 Tantalum, Chip, 4.7u, 6.3V, TCSCS0J475MAAR C11 Chip, 0.1u, CL21B104KNER C12 Tantalum, Chip, 4.7u, 16V, TCSCS1C476MBAR C13 Tantalum, Chip, 4.7u, 6.
Electrical Parts List NO DESCRIPTION SEC. CODE REMARK - Resistors R1 Chip, 47K, RC1608J473CS R2, R3 Chip, 1.8K, RC1608J182CS R4 0.5, 5%, 1/4W, CR1/4W, 0.5, J, TB R5 Chip, 51K, RC1608J513CS R6 Chip, 150K, RC1608J154CS R7 Chip, 200K, RC1608J204CS R8 Chip, 47K, RC1608J473CS R9 Chip, 1M, RC1608J105CS R10, R11 Chip, 39K, RC1608J393CS R12 Chip, 13K, RC1608J133CS R13 Chip, 330, RC1608J331CS R14 Chip, 3.
Electrical Parts List NO DESCRIPTION SEC.
Electrical Parts List 9-5 Travel Charger NO DESCRIPTION SEC. CODE - Capacitors C1 X, 100nF, 250V, KNB15300-104 2305-000139 X, 100nF, 250V, PCX2-335-104 61267-10424ME Electrical, 4.7uF, 250V, 8.5°…, 10°ø12.5mm, CESSL2E4R7M 2401-001233 Electrical, 4.7uF, 250V, 8.5°…, 10°ø12.5mm, SMS2E4R7M 2401-002413 Film, 15nF, 20%, 630V, 400°ø15.5°ø4.5°ø9.5mm, MMD153M630V-12.5P 2305-000199 Film, 15nF, 20%, 630V, 400°ø15.5°ø4.5°ø9.5mm, MMD153M630V-12.
Electrical Parts List NO DESCRIPTION SEC. CODE - Diodes D1 Diode, Bridge, 600V, 1A, S1VB, A60 0402-000524 D2 Diode, FR, 1000V, 1A, BYV38 0402-000495 Diode, FR, 1000V, 1A, UF4007 0402-000012 Diode, Ultra, High, Speed, SOT-23, 85V, 100mA, 0.92V, KDS181 (A3) 60222-00181KA Diode, Ultra, High, Speed, SOT-23, 85V, 100mA, 0.
Electrical Parts List NO DESCRIPTION SEC. CODE R3-R7 Chip, 2012, 39K•ÿ, 1%, RC2012F3902CS 2007-000827 R8, R9 Chip, 2012, 300•ÿ, 5%, RC2012J301CS 2007-000728 R10 Chip, 2012, 1K•ÿ, 1%, RC2012F1001CS 2007-000465 R12 Surage, 1/2W, 4.7M, 5%, RCR50+T524.7MJ 2009-001039 R20 Surage, 1/2W, 4.7M, 5%, RCR50+T524.7MJ 2009-001039 R21 Wire Wound, 1/2W, 0.5•ÿ, 1%, ARW1/2N, 0.
Electrical Parts List NO DESCRIPTION SEC. CODE R57 Chip, 2012, 200•ÿ, 5%, RC2012J201CS 2007-000026 R60 Chip, 2012, 2K•ÿ, 5%, RC2012J202CS 2007-000671 R61 Chip, 2012, 1.
Electrical Parts List 9-30 Samsung Electronics
