High Resolution Varifocal Dome Camera SCD-2080E User Manual SCD-2080E
B T ■ ■ High Resolution Varifocal Dome Camera User Manual Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we’ll introduce our model description.
safety information 6 CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
e e 7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power source and contact the service center. continued use in such a condition may cause fire or electric shock. 9. If this product fails to operate normally, contact the nearest service center. never disassemble or modify this product in any way.
safety information im FCC STATEMENT 1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 2 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
o e t 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
contents in INTRODUCTION 9 INSTALLATION 12 CONNECTION 16 SETUP 18 TROUBLESHOOTING 9 10 11 Features What’s included Component names and functions F 12 15 Installation Adjust the panning and tilting while watching the monitor y y 16 16 17 Connecting to Monitor Connecting to Power Using Coaxial Communications 32 8_ contents y y 18 18 Menu Configration Menu Setup y 31 Troubleshooting y 31 SPECIFICATIONS y y 32 34 Specifications Dimension y y
s introduction FEATURES y Excellent Sensitivity The built-in high sensitivity COLOR CCD produces a clear image. - Color : 0.15Lux(50IRE, @F1.2), 0.0003LUX (SENS-UP, x512) y SSNR3 (Samsung Super Noise Reduction) Function The high-performance W-V DSP chip effectively removes low-light gain noise and afterimage to provide clear images even in dark environments. y Electrical Day & Night This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions.
introduction C WHAT’S INCLUDED Check if the following items are included in the product package.
COMPONENT NAMES AND FUNCTIONS FRONT ● INTRODUCTION ➌ ➒ ❶ ➎ ➑ ➋ ➍ ➏ ➐ ❶ Pan Base : Control panning angle of camera. ➋ Rotate Base : Control rotating angle of camera. ➌ x3.6 Vari-focal Lens Module 2.8 ~ 10.0mm (F1.2) ➍ Video Output Terminal to Monitor ➎ Function Setup switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item.
installation INSTALLATION 1. Separate the dome cover by turning anti-clockwise. 2. Separate the shield case by pulling from the camera body. Latch * To install the dome cover on the camera body, turn the latches in locking direction as shown in the [Figure-1].
WHEN USING THE CEILING BRACKET Ceiling bracket ● INSTALLATION An arrow for installing directions s r M4 tapping screw (provided) CAMERA Locking direction Unlocking direction Dome cover 1. Hold the ceiling bracket (located where the arrow points to) and separate it from the main body of the camera by rotating it anti-clockwise. (refer to the picture in 'Notes' on page 13) 2.
installation Pan Base fixation screw M4 tapping screw [Figure-2] If you want to install the camera with the ceiling bracket together, fix them using two M4 tapping screws at the side of the main body (refer to the [Figure-2] on page 14) 14_ installation A W
73˚ 174˚ 176˚ Rotate Base Tilt Base Pan Base 1. You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism. y Pan Base moves by 176˚ to each side direction and 352˚ on the whole. y Tilt Base covers total 73˚ angle(0˚ ~ 73˚). y Change to read, “Rotate Base moves by 174° to each side direction and 348° in total. 2.
connection CONNECTING TO MONITOR Connect the VIDEO-OUT jack to the VIDEO-IN jack of the monitor. U y y CCTV Camera Monitor y As the connecting method varies with the instruments, refer to the manual supplied with the instrument. y If necessary, you can connect the monitor to the REMOTE jack on the back of your camera. y Only connect the cable when the power is turned off. CONNECTING TO POWER Connect the adaptor to the power input terminal as shown in the figure below.
a. e y .
setup S u S MENU CONFIGRATION MAIN SETUP LENS ● DC EXPOSURE ● BRIGHTNESS ● SENS-UP ● SHUTTER ● RETURN ● AGC WHITE BAL ● ATW ● MANUAL ● OUTDOOR ● AWC→SET ● INDOOR SSDR ● OFF ● ON BACKLIGHT ● OFF ● BLC SSNR3 ● ON ● OFF DAY/NIGHT ● AUTO ● COLOR ● B/W SPECIAL ● IMAGE ADJ ● SYNC ● DIS ● MONITOR ● MOTION DET ● LANGUAGE ● CAM TITLE ● PRIVACY ● RETURN EXIT ● SAVE ● NOT SAVE ● RESET ● HLC MENU SETUP Use the Function Setup switch within the camera. Function Setup switch 1.
Select the function using the Function Setup switch. DC ATW OFF OFF ON AUTO Change the status using the Function Setup switch. ● SETUP MAIN SETUP 䯝 1.LENS 2.EXPOSURE 3.WHITE BAL 4.SSDR 5.BACKLIGHT 6.SSNR3 7.DAY/NIGHT 8.SPECIAL 9.EXIT SAVE 2. Select a desired function using the Function Setup switch. y Place the cursor over a desired item. 3. Set up a selected item by using the Function Setup switch. 4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
setup y BRIGHTNESS : Adjusts the video brightness. EXPOSURE SETUP y SHUTTER : You can select the shutter. 䯝 1.BRIGHTNESS IIIIIÂIIIIIIIIIIIIIIII 25 2.SHUTTER --- A.FLK : Select this when you 3.AGC HIGH experience picture flicker, which can 4.SENS-UP OFF happen when there is a clash with the 5.RETURN frequency of the installed lighting. - ESC : Select this to control the shutter speed automatically.
WHITE BAL (WHITE BALANCE) Use the White Balance function to adjust the screen color. y ay en 2. Select a desired mode using the Function Setup switch. MAIN SETUP 1.LENS 2.EXPOSURE 䯝 3.WHITE BAL 4.SSDR DC ATW OFF ※ Select one of the following 5 modes, as appropriate for your purpose. y ATW : Select this when the color temperature is between 1,700°K and 11,000°K. y OUTDOOR : Select this when the color temperature is between 1,700°K and 11,000°K.
setup SSDR (SAMSUNG SUPER DYNAMIC RANGE) SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas. 1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the Function Setup switch so that the arrow indicates ‘SSDR’. 2. Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas.
or n y BLC : Enables a user to directly select a desired area from a picture and to view the area more clearly. - LEVEL : Adjusts the brightness level of a monitoring area. y HLC (High Light Compensation) : This function masks any areas of peak white light, this minimizes whiteout due to over exposure and thus preserve much of the onscreen details that are within the camera view. - LEVEL : Adjusts the brightness level of a monitoring area. - LIMIT : Enable to change the operating condition.
setup SSNR3 This function reduces the background noise in a low luminance environment. 1. When the SETUP menu screen is displayed, select 'SSNR3' by using the Function Setup switch so that the arrow indicates 'SSNR3' . 2. Select a desired mode using the Function Setup switch. y OFF : Deactivates SSNR3. Noise is not reduced. y ON : Activates SSNR3 so that noise is reduced. 3. Set the SSNR3 mode to 'ON' and press the Function Setup switch. Then you can adjust the noise reduction level. MAIN SETUP 1.LENS 2.
y B/W : The picture is always displayed in black and white. You can turn on or off the burst signal on B/W mode. y AUTO : The mode is switched to ’Color ‘ in a normal environment, but switches to ’B/W‘ mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch. You can turn on or off the burst signal on B/W mode. - DURATION : You can select the day/night switching point. AUTO SETUP ▶ 1.BURST MODE 2.COLOR→B/W DURATION DWELL TIME 3.
setup SPECIAL 1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup switch so that the arrow indicates ‘SPECIAL’. 2. Select a desired mode using the Function Setup switch. y IMAGE ADJ : 1) When the SPECIAL menu screen is displayed, select ‘IMAGE ADJ’ by using the Function Setup switch so that the arrow indicates ’IMAGE ADJ‘. MAIN SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.SSDR 5.BACKLIGHT 6.SSNR3 7.DAY/NIGHT 䯝 8.SPECIAL 9.EXIT SPECIAL #䯝 1.IMAGE ADJ 2.MONITOR 3.CAM TITLE 4.
may appear. y Monitor : Please change the settings value of video appropriate to your monitor. - LCD : Please select this menu item when using an LCD monitor. You can change the gamma, PED level and color gain in the sub menus. - CRT : Please select this menu item when using a CRT monitor. LCD MONITOR ▶ GAMMA 0.55 IIIIIÂIIIIIIIIIIIIIIII 17 PED LEVEL IIIIIIIIIIIIIIIÂIIIIII COLOR GAIN 50 RESET Press SET to Return - USER : Please use this menu item when using a monitor other than standard ones.
setup When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one. English and Numbers are available in the mode. If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY. - SEL POS : Determines which of the 4 vertices of each MD area is to be used. - XPOS : Determines the coordinate of the horizontal axis for SEL POS. - YPOS : Determines the coordinate of the vertical axis for SEL POS. . n - FILL → SET : Fills in a selected MD area. The color of filling is sequentially selected as brown, orange, blue, cyan, yellowish green, yellow, magenta and red.
setup y LANGUAGE : You can select the menu language according to your requirements. y RETURN : Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu. EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose. y SAVE : Save the current settings and exit the MAIN SETUP menu. y NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu. y RESET: Resets the camera settings to the factory defaults.
s. troubleshooting TROUBLESHOOTING N If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. SOLUTION Nothing appears on the screen. ▶ Check that the power cord and line connection between the camera and monitor are fixed properly. ▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack. The image on the screen is dim.
specifications SPECIFICATIONS SCD-2080EN SCD-2080EP D G ELECTRICAL Input Voltage DC 12V / AC 24V W Power Consumption Max 3.5W S M VIDEO Imaging Device 1/3 inch, Diagonal 6mm Super HAD CCD P Total Pixels 811(H) x 508(V) 795(H) x 596(V) 3 Effective Pixels 768(H) x 494(V) 752(H) x 582(V) D Scanning System 2:1 Interlace Synchronization Internal / Line-Lock Frequency H : 15.734KHz V:59.94Hz D S H: 15.625KHz V: 50.00Hz C S Horizontal Resolution COLOR : 600TVL Min.
SCD-2080EN SCD-2080EP Day & Night COLOR / BW / AUTO (S/W Type) Gain Control Low / High / Off White Balance ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K) ● SPECIFICATIONS TROUBLESHOOTING SENS-UP (frame Integration) Auto / Off (Selectable x2 ~ x512) Motion Detection On / Off (8 Programmable zones) Privacy Masking On / Off (12 Programmable zones) 3D Noise Filter (SSNRIII) On / Off (Level adjustable) Digital Zoom On / Off (x1 ~ x16) Digital Image Stabilization(DIS) On / Off Camera
specifications DIMENSION A M Ø107.6 M E E 83.7mm E M 5 R4 B C W to M S F P P 81.
DECLARATION OF CONFORMITY Application of Council Directive(s) 2004 / 108 / EC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-716 European Representative Name European Representative Address Equipment Type/Environment CCTV Camera Model Name SCD-2080EP Beginning Serial NO.
MEMO
MEMO
MEMO
MEMO
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222, FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com SAMSUNG TECHWIN EUROPE LTD.
